共找到 122 条与 发动机零部件 相关的标准,共 9 页
Aircraft Configuration Management with LSAP
Aircraft Configuration Management with LSAP
This amendment forms a art of Military Specification MIL-E-50796 dated 12 June 1973 and is approved for use by all Departments and Agencies of the Department of Defense.
EXPANDING SHIELDED MILD DETONATING CORD ASSEMBLY
This specification is approved for use by all Departments and Agencies of the Department of Defense.
DIE, RETHREADING: AXLE
This specification covers the general requirements for the design, development and preproduction testing of Expanding Shielded Mild Detonating Cord Assembly (ESMDC) to be utilized for aircrew escape systems.This assembly is used in separation systems to remove fastenings between two units and impart a thrust to separate the seunits without contamination of the adj acent area.
EXPANDING SHIELDED MILD DETONATING CORD ASSEMBLY
To provide a standard Adapter Interface and establish accuracies for different sizes of blade classification instruments to permit moment weighing of two blades which when placed 180 degrees apart in a perfect disc, will produce no appreciable static unbalance. The standard Adapter Interface will provide interchangability of adapters between instruments of different manufacturers. The moment weighing scales sizes covered by this document are intended to cover the full range of blades in common use and to detect moment variations from blade to blade when it is positioned at the same radius as in its associated wheel. To provide a standard interface adapter flange on any blade classification instrument capable of meeting the sensitivity requirements for the specific class.
Adapter Interface- Turbine Engine Blade Moment Weighing Scale
This specification covers one grade of silicone compound with a corrosion inhibitor for application to unpainted threaded or nonthreaded mating surfaces of ferrous components between -65' Fahrenheit (F) and 160' F, It is also approprIate for use as alubricant for components fabricated from rubber.
COMPOUND, SILICONE, SOFT FILM
The quality assurance tests of 4.7.3.2.2 and 4.7.3.2.4 shall . Not be performed during vibration."
FIRE CONTROL ASSEMBLY LD 546992 (FOR GUIDANCE CONTROL TEST SET MK 443 MOD 0 AND MOD 1)
This amendment forms a part of Military Specification M T L - s - ~ ~ ~ ~o~f (1o2 SS)ep tember i968 and has been approved by the Naval Ordnance Systems Command, Deptment of the Nayy.
SPEED CONTROL ASSEMBLY LD 546993 (FOR GUIDANCE CONTROL TEST SET MK 443 MOD 0 AND MOD 1)
This amendment forms a part of Military Specification MIL-C-l8164A(OS) dated 11 June 1968, and has been approved by the Naval Ordnance Systems Command, Department of the Navy.
COMPOSITION D-2
This recommended practice defines a method for measuring worn fillet roadside fit involute splines. This concept for measuring worn splines provides a direct wear depth dimension by utilizing the unworn involute surface as a contact point from which to measure the depth of wear on the spline tooth at the pitch diameter. Fig. 1 shows spline wear patterns and pitch diameter gaging points. Gages encompassing this concept would basically consist of fixed and movable probes which contact the unworn involute surface known as the form clearance and the worn surface at the pitch diameter thus providing a direct wear reading which is reflected on a dial indicator. Refer to paragraphs 4 and 5 in Fig. 2.
Inspection of Worn Involute Splines
This specification covers the requirements for the procurement of the Fire Control Assembly, LD546992, and BuWeps Dwg 2452630, herein referred to as "assembly. ' 1 (See 6.1 for description and intended use.)
FIRE CONTROL ASSEMBLY LD 546992 (FOR GUIDANCE CONTROL TEST SET MK 443 MOD 0 AND MOD 1)
This specification covers the requirements for the procurement of the Speed Control Assembly, LD546993, and BuWeps Dwg 2452640, herein referred to as 'lassembly. 11 (See 6.1 for description and intended use.)
SPEED CONTROL ASSEMBLY LD 546993 (FOR GUIDANCE CONTROL TEST SET MK 443 MOD 0 AND MOD 1)
This specification covers a composition used to emulsify and densensitize explosives.
COMPOSITION D-2
This amendment forms a p,at of Military Specification MiL-S-81256(OS), 4 March 1965, and has been approved by the Naval Ordnance Systems Command, Department of the Navy.
SILICA FABRIC, PHENOLIC IMPREGNATED
This specification covers one type of choppedsilica fabric impregnated with a phenolic resin containing silica reinforcement, and supplied in approximate 1/2 -inch squares.
SILICA FABRIC, PHENOLIC IMPREGNATED
This amendment forms a part of Military Specificetion MIL-T-l9U(S&A),18 November 1955.
TRUCK, HAND, 2-WHEEL, COMBINATION TRUCK AND DRAIN RACK
This specification covers the requirements applicable to the design and construction of electric motor driven centrifugal pumps (series type only) for trim and drain service aboard Naval submarines.
PUMPS, CENTRIFUGAL, SUBMARINE TRIM AND DRAIN (SERIES TYPE ONLY)
This specification covers combination barrel or drum trucks and drain racks, equipped with steel wheels and removable double handles,
TRUCK, HAND, 2-WHEEL, COMBINATION TRUCK AND DRAIN RACK
Forming process specification for inner and outer wall parts of converging section and diffusing section of liquid rocket engine
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号