V42 起飞着陆装置 标准查询与下载

AC-25.733-1-1997 国产轮胎在进口运输类飞机上装机批准技术要求

Technical requirements for the approval of domestic tires installed on imported transport aircraft

SAE AIR5052-1997 裂纹开裂及针对带有重点在AerMet 100着陆齿轮钢的增长考虑

This document identifies several avallable materials.It compares properties of selected low-alloy steels to the higher alloyed steels.It also compares failure modes,maintenance,and inspection techniques.Although cost should be a fator when considering the material selection for landing gear applicaton,this document will only focus on the technical aspects.

Crack Initiation and Growth Considerations for Landing Gear Steel with Emphasis on AerMet 100

SAE ARP1595A-1997 飞机前轮转向系统

This document provides recommended practices for the design, development, and verification testing of aircraft nosewheel steering (NWS) systems.

Aircraft Nosewheel Steering Systems

SAE ARP1598A-1997 起落架系统发展计划

This Aerospace Recommended Practice (ARP) is therefore intended to document the process of landing gear system development. Some of the steps covered are mandatory and others are elective, or dependent upon customer requirements or desires. Economics is a very significant factor and for each analysis or test performed, more confidence and assurance of success is gained, but at a price. Some of the steps are performed as a matter of "good engineering practice" and without special recognition. Others are unique to the particular landing gear system and all together comprise a complete development.

Landing Gear System Development Plan

SAE AIR1494A-1997 起落架设计强度的确认

Verification of landing gear design strength is accomplished by dynamic and static test programs. This is essentially a verification of the analytical procedures used to design the gear. An industry survey was recently conducted to determine just what analysis and testing are currently being applied to landing gear. Timing in relation to first flight of new aircraft was also questioned. Opinions were solicited from designers of the following categories and/or types of aircraft: a. military - large land based (bomber); b. mililtary - small land based (fighter); c. military - carrier based (Navy); d. military - helicopter (large); e. military - helicopter (small-attack); f. commercial - large (airliner); g. commercial - small (business); and h. USAF (WPAFB) - recommendations. It is the objective of this AIR to present a summary of these responses. It is hoped that this summary will be useful to designers as a guide and/or check list in establishing criteria for landing gear analysis and test.

Verification of Landing Gear Design Strength

HB 7283-1996 民用航空器磁阻式电动转速表最低性能要求

本标准规定了活塞式发动机作动力源的民用航空器电动转速表（包括指示器和传感器，以下简称仪表）最低性能要求。 　　本标准适用于带或不带表内同步指示器的磁阻式仪表。

Minimum performance requirements for reluctance electric tachometers of civil aircraft

SAE AIR4905-1996 止轮块

The purpose of this document is to present general considerations for the design and use of aircraft wheel chocks. The design and use of aircraft wheel chocks is a good deal more complicated than it may appear at first glance.

Wheel Chocks

HB 7230-1995 飞机前轮转弯系统通用规范

本标准规定了飞机前轮转弯系统的通用要求。 　　本标准适用于新研制的飞机前轮转弯系统。对改进、改型的飞机前轮转弯系统也可参照执行。

General specification for aircraft nose wheel steering system

SAE ARP4834-1995 飞行器轮胎翻新操作规程.斜交和辐条

This SAE Aerospace Recommended Practice (ARP) sets forth criteria for the selection, inspection, retread and repair of worn civil aircraft tires, and the means to verify that the retreaded tire is suitable for continued service. This document is applicable to both bias ply and radial aircraft tires qualified subsequent to the adoption of this document. This document sets for the minimum recommended requirements for retreaded tires used on civil aircraft. It also provides criteria for the escalation of retread level of tires used on civil aircraft. The combined recommendations contained in this document form, an acceptable practice, but not the only practice, for retreaded aircraft tires.

Aircraft Tire Retreading Practice - Bias and Radial

SAE AS4833-1995 航空器新型轮胎标准.偏差和半径

This SAE Aerospace Standard (AS) sets forth criteria for the selection and verification processes to be followed in providing tires that will be suitable for intended use on civil aircraft. This document encompasses new and requalified radial and bias aircraft tires. This document establishes the minimum recommended performance standards for new tires to be used on civil aircraft. All new or requalified tires shall meet these standards.

Aircraft New Tire Standard - Bias and Radial

SAE AIR4894-1995 起落架稳定性

This SAE Aerospace Information Report (AIR) discusses the nature of landing gear stability, describes many common landing gear stability problems, and suggests approaches and methods for solving or avoiding them.

Landing Gear Stability

KS W 2011-1995 航空器木配件的运行方法

? ??? ??? ??? ?? ??? ?? ? ??? ?? ?? ??? ??? ????.

Standard practice for wooden parts of aircraft working

HB 6761-1993 飞机机轮刹车系统设计要求

本标准规定了飞机机轮刹车系统的设计要求。 　　本标准适用于新设计的飞机机轮刹车系统。对改进改型的飞机机轮刹车系统，可根据战术技术要求参照执行。

Aircraft wheel braking system design requirements

HB 6870-1993 飞机地板滑轨型式及尺寸

本标准规定了飞机地板滑轨的基本型式和几何尺寸。 　　本标准适用于飞机、直升机的座椅、床铺，厨房、盥洗室，担架等设备的固定和货物在机上的限动或系留。

Type and size of aircraft floor slide rail

AC-25.735-1-1994 刹车磨损限制要求

Brake Wear Limit Requirements

SAE AS586B-1993 航空器用轮子和制动(砂型和硬模)铸件最低要求

This specification has been declared "NONCURRENT" as of January 2005. It is recommended, therefore, that this document not be specified for new designs. Each of these "NONCURRENT" documents is available from SAE. AS586 is inactive for use in new designs. This document will be retained for historical record only. For the inspection and classification of castings used in aircraft wheel and braking systems, refer to AMS 2175 - Castings, Classification and Inspection of. The design authority shall specify the class and grade of casting in accordance with AMS 2175. To establish minimum quality and inspection requirements for magnesium and aluminum wheel and brake (sand and permanent mold) castings for use on aircraft.

Wheel and Brake (Sand and Permanent Mold) Castings Minimum Requirements for Aircraft Applications

HB 6648-1992 飞机拦阻钩装置

本规范规定了飞机拦阻钩装置的设计、研究、制造、分析、试验和文件编写要求。 　　本规范适用于海军舰基飞机，也适用于陆基飞机。

Aircraft Arresting Hook Device

HB 6645-1992 飞机起落架缓冲器落震试验方法和要求

本标准适用于军用飞机和直升起落架油气式缓冲器和液压弹簧（全油液）缓冲器的落震试验。

Aircraft landing gear buffer drop test method and requirements

HB 6550-1991 民用航空器机轮及机轮—刹车装置最低性能要求

本标准规定了民用航空器（以下称航空器）用机轮及机轮—刹车装置设计和构造、技术指标及鉴定试验的要求。 　　本标准适用于民用航空器的机轮及机轮—刹车装置。

Wheels and wheels of civil aircraft—Minimum performance requirements for braking devices

NAVY MIL-L-22589 D-1991 飞机前起落架型发射系统 飞机噪音

This specification covers the design, development, construction, analysis, test and documentation requirements for a i r c r a f t nose gear launching systems on carrier-type a i r c r a f t for which d e t a i l specifications or other pertinent contractual documents require nose gear launching systems on a i r c r a f t .

LAUNCHING SYSTEM, NOSE GEAR TYPE, AIRCRAFT