W55 纺织制品综合 标准查询与下载

EN ISO 13934-1:2013 纺织品.织物拉伸特性.第1部分:用条样法测定断裂强力和断裂伸长率

Dieser Teil von ISO 13934 legt ein Verfahren zur Bestimmung der Hochstzugkraft und Hochstzugkraft-Dehnung an textilen Flachengebilden mit dem Streifen-Zugversuch fest. ANMERKUNG In ISO 13934-2 wird das als Grab-Zugversuch bekannte Verfahren beschrieben. Zu informativen Verweisungen siehe die Literaturhinweise. Die Prufung gilt hauptsachlich fur gewebte Textilien, einschlieslich Flachengebilde, die durch Vorhandensein von Elastomerfasern oder durch mechanische oder chemische Behandlung elastische Eigenschaften aufweisen. Sie kann auch auf Flachengebilde angewendet werden, die nach anderen Techniken hergestellt wurden. Ublicherweise ist sie nicht anwendbar auf Geotextilien, Vliesstoffe, beschichtete Flachengebilde, Glasfasergewebe und textile Flachengebilde aus Kohlenstofffasern oder Polyolefinbandchengarnen (siehe Literaturhinweise). Das Verfahren legt die Bestimmung der Hochstzugkraft und Hochstzugkraft-Dehnung sowohl an Messproben im Normalklima zum Prufen als auch im nassen Zustand fest. Fur dieses Verfahren sind nur Zugprufmaschinen mit konstanter Prufgeschwindigkeit (CRE) einsetzbar.

Textiles - Tensile properties of fabrics - Part 1: Determination of maximum force and elongation at maximum force using the strip method

ISO 13934-1:2013 纺织品.织物拉伸特性.第1部分:使用条样法测定最大受力和最大受力时的伸长率

This part of ISO 13934 specifies a procedure to determine the maximum force and elongation at maximum force oftextile fabrics using a strip method. NOTE ISO 13934-2 describes the method known as the grab method，For informative references，see Bibliography. The method is mainly applicable to woven textile fabrics，including fabrics which exhibit stretch characteristics imparted by the presence of an elastomeric fibre, mechanical or chemical treatment. LI can be applicable to fabrics produced by other technidqdues. It is not normally applicable to geotextiles， nonwovens, Coated fapbrics,textile-glass woven fabrics, and fabrics made from carpbon fibres or polyolefin tapeyarns (See Bibliography). The method specifies the determination of the maximum force and elongation at maximum force of test specimens in equilibrium with the standard atmosphere fortesting,and oftestspecimens in the wet State. The method is restricted to the use of constant rate of extension (CRE)] testing machines.

Textiles - Tensile properties of fabrics - Part 1: Determination of maximum force and elongation at maximum force using the strip method

BS EN ISO 105-E02:2013 纺织品.色牢度试验.对海水的色牢度

Textiles. Tests for colour fastness. Colour fastness to sea water

EN ISO 105-E01:2013 纺织品.色牢度试验.第E01部分:耐水浸色牢度

Dieser Teil von ISO 105 legt ein Verfahren zur Bestimmung der Widerstandsfahigkeit der Farben von Textilien aller Art und in allen Verarbeitungszustanden gegen das Eintauchen in Wasser fest.

Textiles - Tests for colour fastness - Part E01: Colour fastness to water

EN ISO 105-E04:2013 纺织品.色牢度试验.第E04部分:耐汗渍色牢度

Dieser Teil der ISO 105 legt ein Verfahren zur Bestimmung der Widerstandskraft der Farbe von Textilien aller Art und in allen Verarbeitungszustanden gegen die Einwirkung von menschlichem Schweis fest.

Textiles - Tests for colour fastness - Part E04: Colour fastness to perspiration

SN/T 3582-2013 进出口纺织品 纤维定性分析 麻类纤维

本标准规定了鉴别麻类纤维的旋转方向法、灼烧法、显微镜法、显色法4种试验方法。本标准适用于苎麻纤维、亚麻纤维、大麻纤维、黄麻纤维、剑麻纤维、蕉麻纤维的定性鉴别。

Textile for import and export.Method for identification of fiber.Fibrilia

SN/T 1058.2-2013 进出口纺织品色牢度试验方法 第2部分：耐氯漂和非氯漂色牢度快速检测法

SN/T 1058的本部分规定了一种纺织品在日常洗涤护理条件下耐氯漂和非氯漂色牢度的快速检测试验方法。本部分适用于纺织品耐漂白色牢度的快速检测试验。其中，方法1不适用于含有蛋白质纤维的纺织品耐漂白色牢度的检测。

Test method of colour fastness of textile for import and export.Part 2:Quick determination for colorfastness to chlorine and non-chlorine bleach

SN/T 3508-2013 进出口纺织品中六溴环十二烷的测定 液相色谱-质谱/质谱法

本标准规定了进出口纺织品中六溴环十二烷(参见附录A)的液相色谱-质谱/质谱测定方法。本标准适用于进出口纺织品中alpha-六溴环十二烷、beta-六溴环十二烷、gamma-六溴环十二烷的测定。

Determination of hexabromocyclododecane in import and export textiles.Liquid chromatography tandem mass spectrometry method

SN/T 0464-2013 进出口纺织品 纤维定量分析 氨纶混纺产品

本标准规定了用手工分离法和溶解法测定纺织品中氨纶的定量分析方法。本标准适用于含氨纶的二组分、三组分纺织产品的含量分析。

Textile for import and export.Method for quantitative analysis of fiber.Polyurethane fiber mixture textiles

SN/T 3471.1-2013 进出口纺织品质量符合性评价方法 服装 梭织服装

SN/T 3471的本部分规定了进出口梭织服装符合性评价的要求、程序、结果判定和报告方式。本部分适用于各类进出口梭织服装质量是否符合法规性要求和非法规性要求的符合性评价。

The quality conformity evaluation method of textile for import and export.Clothing.Woven garments

SN/T 2558.5-2013 进出口功能性纺织品检验方法 第5部分：消臭率的测定 检知管法

SN/T 2558的本部分规定了采用检知管测定纺织品消臭率的试验方法。本部分适用于机织物、针织物和非织造布等纺织品。

Testing method for import and export funct ional teotiles.Part 5:Dertermination of deodorant rate.Detector tube

SN/T 1058.1-2013 进出口纺织品色牢度试验方法 第1部分：耐唾液色牢度试验方法

SN/T 1058的本部分规定了纺织品耐唾液色牢度的试验方法。本部分适用于纺织品耐唾液色牢度的检测。

Test method of colour fastness of textile for import and export.Part 1:Test method of colour fastness to saliva

DIN CEN/TR 16422:2013 温度调节性能分类.德文版本CEN/TR 16422-2012

Classification of thermoregulatory properties; German version CEN/TR 16422:2012

ASTM D3511/D3511M-13 纺织纤维的抗起球性和其他相关表面变化的标准试验方法:毛刷式起球试验仪

5.1 Acceptance Testing???This method of testing fabrics for resistance to pilling is not recommended for acceptance testing. If it is used for acceptance testing, it should be used with caution because interlaboratory data are not available. In some cases the purchaser and the supplier may have to test a commercial shipment of one or more specific materials by the best available method, even though the method has not been recommended for acceptance testing. 5.1.1 If there are differences or practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, drawn from the material from which the disparate test results were obtained, and randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias. 5.2 The pilling of textile fabrics is a very complex property because it is affected by many factors which may include type of fiber or blends, fiber dimensions, yarn and fabric construction, fabric finishing treatments and refurbishing method. Testing before refurbishing may be adviseable. The pilling resistance of a specific fabric in actual wear varies more with general conditions of use and individual wearers than in replicate fabric specimens subjected to controlled laboratory tests. This experience should be borne in mind when adopting levels of acceptability for any series of standards. 5.3 Pills vary appreciably in size and appearance and depend on the presence of lint and degree of color contrast. These factors are not evaluated when pilling is rated solely on the number of pills. The development of pills may be accompanied by other surface phenomena such as loss of cover, color change, or the development of fuzz. Since the overall acceptability of a specific fabric is dependent on both the characteristics of the pills and the other factors affecting surface appearance, it is suggested that fabrics tested in the laboratory be evaluated subjectively with regard to their acceptability and not rated solely on the number of pills developed. A series of standards, based on graduated degrees of surface change of the fabric type being tested, may be set up to provide a basis for subjective ratings. The visual standards are most advantageous when the laboratory test specimens correlate closely in appearance with worn fabrics and show a similar ratio of pills to fuzz. Counting the pills and weighing their number with respect to their size and contrast, as a combined measure of pilling resistance, is not recommended because of the excessive time required for counting, sizing, and calculation. 5.4 The degree of fabric pilling is evaluated by comparing the tested specimens with visual standards, which may be actual fabrics or photographs of fabrics, showing a range of pilling resistance. The observed resistance to pilling is reported on an arbitrary scale ranging from 5 (no pilling) to 1 (very severe pilling). 5.5 This test method is applica......

Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Brush Pilling Tester

ASTM D2261-13 用舌(单瑞普)程序(恒速扩展拉力试验机)测定织物撕裂强度的标准试验方法

5.1 This test method is considered satisfactory for acceptance testing of commercial shipments since current estimates of between-laboratory precision are acceptable, and the test method is used extensively in the trade for acceptance testing. 5.1.1 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of fabric of the type in question. Test specimens then should be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using the appropriate statistical analysis and an acceptable probability level chosen by the two parties before testing is begun. If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias. 5.2 The force registered in a tear test is irregular, and as a consequence, empirical methods have had to be developed to obtain usable values related to tear strength. In spite of the empirical nature of the reported values, the values are considered to reflect comparative performance of similar fabrics tested and measured in the same way. No known procedure is available that can be used with all fabrics to determine the minimum tearing strength. 5.3 Depending on the nature of the specimen, the data recording devices will show the tearing force in the form of a peak or peaks. The highest peaks appear to reflect the strength of the yarn components, fiber bonds, or fiber interlocks, individually or in combination, needed to stop a tear in a fabric of the same construction. The valleys recorded between the peaks have no specific significance. The minimum tearing force, however, is indicated to be above the lowest valleys. 5.4 Most textile fabrics can be tested by this test method. Some modification of clamping techniques may be necessary for a given fabric due to its structure. Strong fabrics or fabrics made from glass fibers usually require special adaptation to prevent them from slipping in the clamps or being damaged as a result of being gripped in the clamps. 5.5 The CRE-type tensile testing machine has become the preferred test apparatus for determining tongue tearing strength. It is recognized that some constant-rate-of-traverse-type (CRT) tensile testing machines continue to be used. Consequently, these test instruments may be used when agreed upon between the purchaser and the supplier. The conditions for use of the CRT-type tester are included in Appendix X1. 1.1 This test method covers the measurement of the tearing strength of textile fabrics by the tongue (single rip) procedure using a recording constant-rate-of-extension-type (CRE) tensile testing machine. 1.1.1 The CRE-type tensile testing machine has become the preferred test apparatus for determining tongue tearing ......

Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine)

ASTM D5430-13 织物目视检验分级的标准试验方法

5.1 Test Method D5430 is considered satisfactory for acceptance testing a commercial shipments since the method has been used extensively in the trade for grading of fabric and fabric acceptance determination. 5.2 The penalty points obtained in grading the same rolls or bolts of fabric may vary considerably when using each of the three options listed herein. For this reason, the same point assignment option should be used in cases of disagreement arising from differences of values reported by the purchaser and the supplier. 5.3 If there are differences of practical significance between reported test results for two laboratories (or more), comparative test should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, ensure the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results ere obtained, and are randomly assigned in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias. 1.1 These test methods describe a procedure to establish a numerical designation for grading of fabrics from a visual inspection. 1.2 These test methods may be used for the delivery and acceptance of fabrics with requirements mutually agreed upon by the purchaser and the supplier. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Visually Inspecting and Grading Fabrics

ASTM D3786/D3786M-13 织物破裂强度的标准试验方法.薄膜破裂强度试验器法

5.1 This method for the determination of diaphragm bursting strength of knitted, nonwoven and woven fabrics is being used by the textile industry for the evaluation of a wide variety of end uses. 5.2 In cases where test results obtained using the procedures in Test Method D3786 have not been correlated with actual performance, Test Method D3786 is considered satisfactory for acceptance testing of commercial shipments of textile fabrics for bursting strength since the method has been used extensively in the trade for acceptance testing. In cases where disagreement arising from differences in values reported by the purchaser and the supplier when using Test Method D3786 for acceptance testing, the statistical bias, if any, between the laboratory of the purchaser and the laboratory of the supplier should be determined with comparison based on testing specimens randomly drawn from one sample of material of the type being evaluated.Note 2???The kind of load transfer and stretch that occur when knitted goods and nonwoven fabrics are worn are prevented by clamping them as described in this method. 1.1 This test method describes the measurement of the resistance of textile fabrics to bursting using a hydraulic or pneumatic diaphragm bursting tester. This test method is generally applicable to a wide variety of textile products. 1.2 This test method may also be applicable for stretch woven and woven industrial fabrics such as inflatable restraints. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.Note 1???For the measurement of the bursting strength by means of a ball burst mechanism, refer to Test Method D3787. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Bursting Strength of Textile Fabricsmdash;Diaphragm Bursting Strength Tester Method

ASTM D3939/D3939M-13 织物防钩丝性的标准试验方法(钉锤法)

5.1 This test method is not considered satisfactory for acceptance testing of commercial shipments of fabrics because the between-laboratory precision of the test method is poor (see 15.1). 5.1.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative test should be performed to determine if there is a statistical significant difference between them, using competent statistical assistance. As a minimum, use the samples for such a comparative test that are as homogeneous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing and randomly assigned in equal numbers to each laboratory. The test results from the laboratories involved should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If bias is found, either its cause must be found and corrected or future testing for that material must be adjusted in consideration of the statistically significant differences. 5.2 This test method may be used for quality control testing of fabrics during manufacturing and product comparisons of different fabrics by manufacturers, retailers, and users. This test method may also be used by researchers to examine the effect of new fibers, yarns, fabric constructions, and finishes on the snagging resistance of fabrics. 5.3 This test method may be used to test the snagging resistance of most apparel and home furnishings fabrics. However, a different test method may be needed for different types of fabrics and different end-uses (such as towels, pants, and upholstery) (see 5.3.1). 5.3.1 Some fabrics that may not be suitable for this test method are described in 1.2. Many open construction fabrics can be tested for snagging resistance using AATCC Test Method 65. The snagging resistance of many pile floor coverings can be tested by Test Method D1335. Test Method D5362 (Bean Bag) may also be considered as an alternative for testing the snagging resistance of fabrics. This test method does not apply to the ABC Snag Tester. 5.4 Since fabric snagging can be affected by laundering or drycleaning, it may be advisable to test the snagging resistance of a fabric before and after laundering or drycleaning. 5.5 The snagging resistance of a specific fabric varies with individual wearers and general conditions of use. Therefore, it can be expected that garments of the same fabric will show a fairly wide snagging resistance spectrum after wear and much greater variation in wear than in replicate fabric specimens subjected to controlled laboratory tests. This factor should be considered when adopting levels of acceptability for any specification that includes snagging resistance. 5.6 Snags observed in worn garments vary appreciably in number a..........

Standard Test Method for Snagging Resistance of Fabrics (Mace)

ASTM D7811-13(2017) 使用工具测量弓纬和纬斜的标准试验方法

5.1 This test method provides a standard procedure for obtaining data for research and development, quality control, acceptance and rejection under specifications, and for special purposes. 5.2 The data obtained by this test method is applicable to the material under the conditions of this particular test and is not necessarily the same as obtained under other environments in use. 5.3 This test method is considered satisfactory for acceptance testing of commercial shipments. 5.4 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. Other fabrics with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. 5.5 Bow or skew can be induced during fabric manufacturing, dyeing, tentering, finishing, or other operations where a potential exists for uneven distribution of tensions across the fabric width. Bow and skew are more visually displeasing in colored, patterned fabrics such as plaids and horizontal stripes rather than in solid colors because the contrast makes the distortion more prominent. These defects may cause sewing problems in such fabrics and draping problems in finished products. Wavy or sharp breaks in the bow line are more detrimental to the appearance of small specimens of a sewn assembly. 1.1 This test method is used to determine the bow and skew of woven and knitted fabrics over a fixed distance, using a measuring tool. 1.2 This test method is useful when a small specimen or cut parts need to be evaluated for bow and skew, provided a warp or fill, or both, reference line is available, to aid in aligning the tool. 1.3 Test Method D3882 may be used when measuring bow and skew in fabric in rolls. However, results obtained with D3882 may not be comparable with results obtained by this test method. 1.4 There is no known ISO equivalent standard. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standar......

Standard Test Method for Bow and Skew Using a Measuring Tool

KS M 7710-2012 冲洗毛巾

이 표준은 수세용으로 사용하는 종이 타월(이하 타월이라 한다.)에 대하여 규정한다.

Hand towel