Y22 日用玻璃制品 标准查询与下载

EN 16290-1:2014 玻璃封装.用螺丝封口的压力胶囊.第1部分:可回收玻璃MAC 7,5 R完成

This European Standard specifies the dimensions of the 28 mm screw finish for glass containers designated MCA 7,5 R finish for returnable glass.

Glass packaging - Screw finishes for pressure capsules - Part 1: Returnable glass MCA 7@5 R finish

EN 16287-2:2014 玻璃封装.用螺丝封口的压力胶囊.第2部分:单向MAC 1完成

This European Standard specifies the dimensions of the 28 mm screw finish for glass containers designated MCA 1 for one way glass.

Glass packaging - Screw finishes for pressure capsules - Part 2: One way glass MCA 1 finish

JIS S 2350:2014 带有容量指示的玻璃容器

Glass container with content volume indicated

DB34/T 1686-2012 婴幼儿用玻璃奶瓶

本标准规定了婴幼儿用玻璃奶瓶的产品分类、要求、试验方法、检验规则、包装、标志、运输和贮存。 本标准适用于婴幼儿用玻璃奶瓶。

baby glass feeding bottle

DB32/ 2153-2012 日用玻璃单位产品能耗限额及计算方法

Energy consumption limit and calculation method per unit product of glass for daily use

ASTM C148-12 玻璃容器偏振检验的标准试验方法

These two test methods are provided for evaluating the quality of annealing. These test methods can be used in the quality control of glass containers or other products made of similar glass compositions, where the degree of annealing must be verified to ensure quality products. These test methods apply to glass containers manufactured from commercial soda-lime-silica glass compositions.1.1 These test methods describe the determination of relative optical retardation associated with the state of anneal of glass containers. Two alternative test methods are covered as follows: Sections Test Method AComparison with Reference Standards Using a Polariscope6 to 9 Test Method BDetermination with Polarimeter10 to 12 1.2 Test Method A is useful in determining retardations less than 150 nm, while Test Method B is useful in determining retardations less than 565 nm. Note 18212;The apparent temper number as determined by these test methods depends primarily on (1) the magnitude and distribution of the residual stress in the glass, (2) the thickness of the glass (optical path length at the point of grading), and ( 3) the composition of the glass. For all usual soda-lime silica bottle glass compositions, the effect of the composition is negligible. In an examination of the bottom of a container, the thickness of glass may be taken into account by use of the following formula, which defines a real temper number, TR, in terms of the apparent temper number, TA, and the bottom thickness, t: TR = TA (0.160/t) where t is in inches, or TR = TA (4.06/t) where t is in millimetres. This thickness should be measured at the location of the maximum apparent retardation. Interpretation of either real or apparent temper number requires practical experience with the particular ware being evaluated. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Polariscopic Examination of Glass Containers

QB/T 4162-2011 玻璃杯

本标准规定了玻璃杯的术语和定义、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于钠钙硅玻璃制造的玻璃杯，包括压制玻璃杯和吹制玻璃杯。 本标准不适用于有柄玻璃杯、高脚玻璃杯和钢化玻璃杯。

Glass Tumblers

DB34/T 1409-2011 钾钡水晶玻璃

本标准规定了钾钡水晶玻璃的技术要求、试验方法、检验规则和标志、包装、运输、储存。本标准适用于钾钡水晶玻璃板材及其制品。

Rock crystal glass

DB34/T 1410-2011 玻璃饮料壶

本标准规定了玻璃饮料壶的要求、试验方法、检验规则和标志、包装、运输、储存。本标准适用于压制和吹制玻璃饮料壶。

Glass jug

QB/T 1997-2010 照相明胶

本标准规定了照相明胶的分类、要求、试验方法、检验规则和包装、运输、贮存。 本标准适用于以动物的皮、骨等为原料所生产的用于感光材料的明胶。

Photographic gelatin

QB/T 4064-2010 餐饮用钢化玻璃器皿

本标准规定了餐饮用钢化玻璃器皿产品系列的术语和定义、分类、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于餐饮用钠钙玻璃钢化器皿系列和热弯钢化玻璃器皿。本标准不适用于未经本标准定义的钢化工艺处理的普通玻璃器皿，也不适用于口部钢化或半钢化玻璃杯和其他强化玻璃器皿。

Tempered glassware for eating and drinking

IWA 8-2009 餐具,礼品,珠宝,灯具.玻璃透明度.分类和试验方法

Tableware, giftware, jewellery, luminaries - Glass clarity - Classification and test method

SN/T 2116-2008 进出口玻璃器皿检验规程

Rules for the inspection of glassware for import and export

SANS 1003:2006 家用精致磁器和玻化餐具

covers the requirements for fine china and vitrified tableware for domestic use.

Fine china and vitrified tableware for domestic use

ASTM C1648-06 选用一种方法测定玻璃折射和色散系数的标准指南

1.1 This guide identifies and describes seven test methods for measuring the index of refraction of glass, with comments relevant to their uses such that an appropriate choice of method can be made. Four additional methods are mentioned by name, and brief descriptive information is given in Annex A1. The choice of a test method will depend upon the accuracy required, the nature of the test specimen that can be provided, the instrumentation available, and (perhaps) the time required for, or the cost of, the analysis. Refractive index is a function of the wavelength of light; therefore, its measurement is made with narrow-bandwidth light. Dispersion is the physical phenomenon of the variation of refractive index with wavelength. The nature of the test-specimen refers to its size, form, and quality of finish, as described in each of the methods herein. The test methods described are mostly for the visible range of wavelengths (approximately 400 to 780m); however, some methods can be extended to the ultraviolet and near infrared, using radiation detectors other than the human eye.1.1.1 List of test methods included in this guide:Becke line (method of central illumination),Apparent depth of microscope focus (the method of the Duc de Chaulnes),Critical Angle Refractometers (Abbe type and Pulfrich type),Metricon system,Vee-block refractometers,Prism spectrometer, andSpecular reflectance.1.1.2 Test methods presented by name only (see Annex A1):Immersion refractometers,Interferometry,Ellipsometry, andMethod of oblique illumination.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.2 Warning-Refractive index liquids are used in several of the following test methods. Cleaning with organic liquid solvents also is specified. Degrees of hazard associated with the use of these materials vary with the chemical nature, volatility, and quantity used. See manufacturer's literature and general information on hazardous chemicals.

Standard Guide for Choosing a Method for Determining the Index of Refraction and Dispersion of Glass

SANS 1236:2005 一般用途镀银玻璃镜

Covers two classes (based on the type of glass used) of silvered glass mirrors for general use. Specifies requirements for general appearance, optical quality, silver, copper and organic coatings, and resistance to salt fog.

Silvered glass mirrors for general use

ISO 9100-7:2005 玻璃容器.真空凸缘瓶口.第7部分:深度为58

This document specifies the dimensions of vacuum lug finish with nominal size of 58 mm deep for wide-mouth glass containers.

Glass containers - Vacuum lug finishes - Part 7: 58 deep

ISO 9100-8:2005 玻璃容器.真空凸缘瓶口.第8部分:普通规格63、66和70

This document specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm regular for wide-mouth glass containers.

Glass containers - Vacuum lug finishes - Part 8: 63, 66 and 70 regular

ISO 9100-6:2005 玻璃容器.真空凸缘瓶口.第6部分:普通规格53和58

This document specifies the dimensions of vacuum lug finishes with nominal sizes of 53 mm and 58 mm regular for wide-mouth glass containers.

Glass containers - Vacuum lug finishes - Part 6: 53 and 58 regular

ISO 9100-5:2005 玻璃容器.真空凸缘瓶口.第5部分:普通规格43和48

This document specifies the dimensions of vacuum lug finishes with a nominal size of 43 mm and 48 mm regular for wide-mouth glass containers.

Glass containers - Vacuum lug finishes - Part 5: 43 and 48 regular