B4.0M-2000 发布历史

This standard covers the common tests for the mechanical testing of welds. They are defined and illustrated in five parts related to testing of groove welds@ fillet welds@ and stud welds. The tests include: bend tests@ tension tests@ fracture toughness tests@ soundness tests@ shear tests@ nick-break test@ hardness tests@ stud weld tests@ and selected weldability tests. This document extensively uses American Society for Testing and Materials (ASTM) Standard Methods and specifies how to use these methods when testing weldments. It takes into consideration the variations in properties that can occur between different regions (base metal@ heat-affected zone@ and weld metal) of a weldment. Methods of hardness testing and mechanical property tests for base metals are covered by ASTM standards or the individual material specification. The joint tests for brazements are covered in AWS C3.2@ Standard Methods for Evaluating the Strength of Brazed Joints in Shear. This Foreword applies to all five parts. Additional information on the mechanical testing of welded joints may be obtained from the AWS Welding Handbook@ Volume 1. The values stated in SI Units and used throughout this document are to be regarded as standard. Recommendation for style and usage of SI Units may be found in AWS A1.1@ Metric Practice Guide for the Welding Industry. An expanded section on weldability testing is included in this edition of B4.0M. Selected weldability test methods are described. Safety Precautions. Safety precautions shall conform to the latest edition of ANSI 249.1@ Safety in Welding@ Cutting@ and Allied Processes@ published by the American Welding Society. Note: This standard may involve hazardous materials@ operations@ and equipment. The standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user to establish appropriate safety and health practices. The user should determine the applicability of any regulatory limitations prior to use. Comments or inquiries on this standard are welcome. They should be sent to the Secretary@ AWS B4 Committee on Mechanical Testing of Welds@ American Welding Society@ 550 N.W. LeJeune Road@ Miami@ FL 33126. Official interpretations of any of the technical requirements of this standard may be obtained by sending a request@ in writing@ to the Managing Director@ Technical Services@ American Welding Society@ 550 N.W. LeJeune Road@ Miami@ FL 33126. A formal reply will be issued after review by the appropriate personnel following established procedures.

B4.0M-2000由AWS - American Welding Society 发布于 2000-01-01，并于 2010-08-25 实施。

B4.0M-2000 发布之时，引用了标准

115 *， 2014-01-01 更新

* 在 B4.0M-2000 发布之后有更新，请注意新发布标准的变化。

B4.0M-2000的历代版本如下：

2000年01月01日 B4.0M-2000

非常抱歉，我们暂时无法提供预览，您可以试试：免费下载 B4.0M-2000 前三页，或者稍后再访问。

注意：点击下载后，生成下载文件时间比较长，请耐心等待......

标准号: B4.0M-2000
发布日期: 2000年01月01日
实施日期: 2010年08月25日
废止日期: 无
中国标准分类号: /
国际标准分类号: /
发布单位: AWS - American Welding Society
引用标准: 115

适用范围: This standard covers the common tests for the mechanical testing of welds. They are defined and illustrated in five parts related to testing of groove welds@ fillet welds@ and stud welds. The tests include: bend tests@ tension tests@ fracture toughness tests@ soundness tests@ shear tests@ nick-break test@ hardness tests@ stud weld tests@ and selected weldability tests. This document extensively uses American Society for Testing and Materials (ASTM) Standard Methods and specifies how to use these methods when testing weldments. It takes into consideration the variations in properties that can occur between different regions (base metal@ heat-affected zone@ and weld metal) of a weldment. Methods of hardness testing and mechanical property tests for base metals are covered by ASTM standards or the individual material specification. The joint tests for brazements are covered in AWS C3.2@ Standard Methods for Evaluating the Strength of Brazed Joints in Shear. This Foreword applies to all five parts. Additional information on the mechanical testing of welded joints may be obtained from the AWS Welding Handbook@ Volume 1. The values stated in SI Units and used throughout this document are to be regarded as standard. Recommendation for style and usage of SI Units may be found in AWS A1.1@ Metric Practice Guide for the Welding Industry. An expanded section on weldability testing is included in this edition of B4.0M. Selected weldability test methods are described. Safety Precautions. Safety precautions shall conform to the latest edition of ANSI 249.1@ Safety in Welding@ Cutting@ and Allied Processes@ published by the American Welding Society. Note: This standard may involve hazardous materials@ operations@ and equipment. The standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user to establish appropriate safety and health practices. The user should determine the applicability of any regulatory limitations prior to use. Comments or inquiries on this standard are welcome. They should be sent to the Secretary@ AWS B4 Committee on Mechanical Testing of Welds@ American Welding Society@ 550 N.W. LeJeune Road@ Miami@ FL 33126. Official interpretations of any of the technical requirements of this standard may be obtained by sending a request@ in writing@ to the Managing Director@ Technical Services@ American Welding Society@ 550 N.W. LeJeune Road@ Miami@ FL 33126. A formal reply will be issued after review by the appropriate personnel following established procedures.

B4.0M-2000

Standard Methods for Mechanical Testing of Welds