R 49-2009

Standard Practice for Determination of Low- Temperature Performance Grade (PG) of Asphalt Binders

R 49-2009 发布历史

This standard practice covers the determination of low-temperature properties of asphalt binders using data from the bending beam rheometer (T 313) and the direct tension tester (T 314). This standard practice can be used on data from unaged material or from material aged using T 240 (RTFOT)@ R 28 (PAV)@ or T 240 (RTFOT) and R 28 (PAV). This standard practice can be used on data generated within the temperature range from +6 to ?C36?? This standard practice is only valid for data on materials that fall within the scope of suitability for both test methods T 313 and T 314. This standard practice can be used to determine the following: PG Grade Determination of an Asphalt Binder??The determination of a low-temperature grade or grades that are satisfied by an asphalt binder. The determination of the temperature corresponds to the specification parameter@ Tcr@ the critical cracking temperature. Prequalification of an Asphalt Binder??The procedure required to qualify an asphalt binder for supply. Verification of an Asphalt Binder Grade??The testing required to certify that a binder complies with an existing prequalified binder. While this standard practice determines the critical cracking temperature for typical hot mix asphalt (HMA)@ the intent of this standard practice is grading of asphalt binder according to M 320@ not performance prediction for asphalt pavement. This standard practice should not be used in lieu of T 322. This standard practice may involve hazardous materials@ operations@ and equipment. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this procedure to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. Note 1??The algorithms contained in this standard require implementation by a person trained in the subject of numerical methods and viscoelasticity. However@ due to the complexity of the calculations they must@ of necessity@ be performed on a computer. Software to perform the calculations may be written or purchased as a spreadsheet or as a stand-alone program.2

R 49-2009由AASHTO - American Association of State Highway and Transportation Officials 发布于 2009-01-01，并于 2018-09-10 实施。

R 49-2009的历代版本如下：

• 2009年01月01日 R 49-2009

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 R 49-2009 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

R 49-2009

发布日期

2009年01月01日

实施日期

2018年09月10日

废止日期

无

中国标准分类号

/

国际标准分类号

/

发布单位

AASHTO - American Association of State Highway and Transportation Officials

引用标准

19

适用范围

This standard practice covers the determination of low-temperature properties of asphalt binders using data from the bending beam rheometer (T 313) and the direct tension tester (T 314). This standard practice can be used on data from unaged material or from material aged using T 240 (RTFOT)@ R 28 (PAV)@ or T 240 (RTFOT) and R 28 (PAV). This standard practice can be used on data generated within the temperature range from +6 to ?C36?? This standard practice is only valid for data on materials that fall within the scope of suitability for both test methods T 313 and T 314. This standard practice can be used to determine the following: PG Grade Determination of an Asphalt Binder??The determination of a low-temperature grade or grades that are satisfied by an asphalt binder. The determination of the temperature corresponds to the specification parameter@ Tcr@ the critical cracking temperature. Prequalification of an Asphalt Binder??The procedure required to qualify an asphalt binder for supply. Verification of an Asphalt Binder Grade??The testing required to certify that a binder complies with an existing prequalified binder. While this standard practice determines the critical cracking temperature for typical hot mix asphalt (HMA)@ the intent of this standard practice is grading of asphalt binder according to M 320@ not performance prediction for asphalt pavement. This standard practice should not be used in lieu of T 322. This standard practice may involve hazardous materials@ operations@ and equipment. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this procedure to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. Note 1??The algorithms contained in this standard require implementation by a person trained in the subject of numerical methods and viscoelasticity. However@ due to the complexity of the calculations they must@ of necessity@ be performed on a computer. Software to perform the calculations may be written or purchased as a spreadsheet or as a stand-alone program.2