A5.4/A5.4M-2006

Specification for Stainless Steel Electrodes for Shielded Metal Arc Welding

A5.4/A5.4M-2006 发布历史

This specification prescribes requirements for the classification of covered stainless steel electrodes for shielded metal arc welding.1@2 The chromium content of weld metal deposited by these electrodes is not less than 10.5 percent and the iron content exceeds that of any other element. For purposes of classification@ the iron content shall be derived as the balance element when all other elements are considered to be at their minimum specified values.Note: No attempt has been made to classify all grades of filler metals within the limits of the above scope; only the more commonly used grades have been included.Safety and health issues and concerns are beyond the scope of this standard and@ therefore@ are not fully addressed herein. Some safety and health information can be found in Annex Clauses A5 and A11. Safety and health information is available from other sources@ including@ but not limited to ANSI Z49.1@ Safety in Welding@ Cutting@ and Allied Processes@ and applicable state and federal regulations.This specification makes use of both U.S. Customary Units and the International System of Units [SI]. The measurements are not exact equivalents; therefore@ each system must be used independently of the other without combining in any way when referring to material properties. The specification with the designation A5.4 uses U.S. Customary Units. The specification A5.4M uses SI Units. The latter are shown in brackets [ ] or in appropriate columns in tables and figures. Standard dimensions based on either system may be used for sizing of filler metal or packaging or both under A5.4 or A5.4M specifications.1 Due to possible differences in composition@ core wire from covered electrodes should not be used as bare filler wire.2 Classifications E502@ E505@ and E7Cr are no longer specified by this document. They are specified in AWS A5.5/ A5.5M:2006@ designated as follows: E502 as E801X-B6 and E801X-B6L@ E505 as E801X-B8 and E801X-B8L@ and E7Cr as E801X-B7 and E801X-B7L.

A5.4/A5.4M-2006由AWS - American Welding Society 发布于 2006-01-01，并于 2006-05-15 实施。

A5.4/A5.4M-2006的历代版本如下：

• 2006年01月01日 A5.4/A5.4M-2006
• 2012年01月01日 A5.4/A5.4M-2012

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 A5.4/A5.4M-2006 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

A5.4/A5.4M-2006

发布日期

2006年01月01日

实施日期

2006年05月15日

废止日期

无

中国标准分类号

/

国际标准分类号

/

发布单位

AWS - American Welding Society

引用标准

54

适用范围

This specification prescribes requirements for the classification of covered stainless steel electrodes for shielded metal arc welding.1@2 The chromium content of weld metal deposited by these electrodes is not less than 10.5 percent and the iron content exceeds that of any other element. For purposes of classification@ the iron content shall be derived as the balance element when all other elements are considered to be at their minimum specified values.Note: No attempt has been made to classify all grades of filler metals within the limits of the above scope; only the more commonly used grades have been included.Safety and health issues and concerns are beyond the scope of this standard and@ therefore@ are not fully addressed herein. Some safety and health information can be found in Annex Clauses A5 and A11. Safety and health information is available from other sources@ including@ but not limited to ANSI Z49.1@ Safety in Welding@ Cutting@ and Allied Processes@ and applicable state and federal regulations.This specification makes use of both U.S. Customary Units and the International System of Units [SI]. The measurements are not exact equivalents; therefore@ each system must be used independently of the other without combining in any way when referring to material properties. The specification with the designation A5.4 uses U.S. Customary Units. The specification A5.4M uses SI Units. The latter are shown in brackets [ ] or in appropriate columns in tables and figures. Standard dimensions based on either system may be used for sizing of filler metal or packaging or both under A5.4 or A5.4M specifications.1 Due to possible differences in composition@ core wire from covered electrodes should not be used as bare filler wire.2 Classifications E502@ E505@ and E7Cr are no longer specified by this document. They are specified in AWS A5.5/ A5.5M:2006@ designated as follows: E502 as E801X-B6 and E801X-B6L@ E505 as E801X-B8 and E801X-B8L@ and E7Cr as E801X-B7 and E801X-B7L.