CSA/ANSI NGV 2-2023由SCC 发布于 2023-07-01。
CSA/ANSI NGV 2-2023在国际标准分类中归属于: 75.160.30 气体燃料。
CSA/ANSI NGV 2-2023 的最新版本是哪一版？
最新版本是 CSA/ANSI NGV 2-2023 。
CSA/ANSI NGV 2-2023 由 ANSI NGV 2-2007 天然气汽车集装箱 变更而来。
1 Scope 1.1 General This Standard concerns high-pressure containers for the on-board storage of natural gas as a fuel for automotive vehicles. This Standard contains requirements for the material, design, manufacture, and testing of serially produced, refillable Type NGV 2 containers intended for the storage of compressed natural gas (CNG) for vehicle operation. These containers are to be permanently attached to the vehicle. This Standard applies to containers up to and including 1000 L (35.4 ft3) water capacity. Note: In Canada, the use of gas containers is governed by the Act. In the United States, the use of gas containers is governed by the U.S. Department of Transportation 1.2 Container types 1.2.1 Cylindrical containers Type NGV 2 containers are designated as follows: a) Type 1: metal; b) Type 2: hoop-wrapped container with resin-impregnated continuous filaments and a metal liner with a minimum burst pressure of 125% of service pressure; c) Type 3: fully wrapped container with resin-impregnated continuous filaments and with a metal liner; and d) Type 4: fully wrapped container with resin-impregnated continuous filaments and with a nonmetallic liner. 1.2.2 Conformable containers Conformable container types are designated as follows: a) CT1: container or assembly of a non-cylindrical or non-spherical (i.e., irregular) shape without a protective shell (i.e., outside wall containing gas pressure); b) CT2: container or assembly of possibly irregular shape within a conformable protective shell that is acting as a shield and not directly assisting the inner container with containing gas pressure; and c) CT3: container or assembly of possibly irregular shape within a conformable protective shell that is acting as a shield and directly assisting the inner container with containing gas pressure. The conformable container types are an additional identifier that is used in combination with the container type. A conformable container is designated based on the design as a Type 1 (metal) to Type 4 (resin-impregnated continuous filament with a nonmetallic liner) with the additional conformable type identifier. For example, a Type 4 CT2 container would be required to meet the criteria for a Type 4 container as well as the criteria specified for a CT2 container. 1.3 Welded containers This Standard does not cover welded metal containers or liners. 1.4 Precedence of requirements Where a clause in this Standard conflicts with codes or standards referenced in this Standard, the requirements of this Standard take precedence. 1.5 Requalification of containers Type 1 steel containers may be requalified for further service in accordance with the procedure described in Annex E. 1.6 Canadian specific requirements Annex Acontains requirements that are applicable only to Canada. 1.7 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.8 Units of measure The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. See also Annex D.
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证：京ICP证110310号