SAE J1199-2013
SAE J 1199-2013

Mechanical and Material Requirements for Metric Externally Threaded Steel Fasteners

SAE J1199-2013 发布历史

This SAE Standard covers the mechanical and material requirements for eight property classes of steel@ externally threaded metric fasteners in sizes M1.6 through M36@ inclusive@ and suitable for use in automotive and related applications. Products included are bolts@ screws@ studs@ U-bolts@ preassembled screw and washer assemblies (sems)@ and products manufactured the same as sems except without washer. Products not covered are tapping screws@ thread-rolling screws@ and self-drilling screws@ Mechanical and material requirements for these products are covered in other SAE documents. The term stud as referred to herein@ applies to a cylindrical rod of moderate length@ threaded on either one or both ends or through its entire length. It does not apply to headed@ collard@ or similar products which are more closely characterized by requirements shown herein for bolts. For specification purpose@ this document treats U-bolts as studs. Thus@ wherever the word studs appear@ U-bolts is also implied. U-bolts covered by this documents are those used primarily in the suspension and related areas of vehicles@ (Designers should recognize that the U configuration may not sustain a load equivalent to two bolts ro studs of the same size and grade@ thus actual load-carrying capacity of U-bolts should be determined by saddle load tests.)

SAE J1199-2013由SAE - SAE International 发布于 2013-02-01，并于 2013-09-13 实施。

SAE J1199-2013 发布之时，引用了标准

• ASTM A307-2012 抗拉强度为60000 PSI的碳钢螺栓、螺柱和螺杆的标准规格*， 2022-12-17 更新
• ASTM A354-2011 淬火与回火合金钢螺栓螺柱及其他外螺纹紧固件的标准规格*， 2022-12-17 更新
• ASTM A449-2010 通用最低拉伸强度为120/105/90 ksi的热处理钢制六角头螺钉,螺栓和螺柱用标准规格*， 2022-12-17 更新
• ASTM F606-2011 测定外螺纹和内螺纹紧固件,垫圈,直接拉力指示器和铆钉的机械性能的标准试验方法*， 2022-12-17 更新
• SAE J 121M-1997 淬火和回火米制螺纹紧固件的脱碳

* 在 SAE J1199-2013 发布之后有更新，请注意新发布标准的变化。

SAE J1199-2013的历代版本如下：

• 1978年02月01日 SAE J1199-1978 SAE J 1199-1978
• 1983年09月01日 SAE J1199-1983 SAE J 1199-1983
• 1996年12月01日 SAE J1199-1996 SAE J 1199-1996
• 2001年03月01日 SAE J1199-2001 米制外螺纹钢紧固件的机械和材料要求
• 2013年02月18日 SAE J1199-2013 公制外螺纹钢紧固件的机械和材料要求

标准号

SAE J1199-2013

发布日期

2013年02月01日

实施日期

2013年09月13日

废止日期

无

中国标准分类号

/

国际标准分类号

/

发布单位

SAE - SAE International

引用标准

10

适用范围

This SAE Standard covers the mechanical and material requirements for eight property classes of steel@ externally threaded metric fasteners in sizes M1.6 through M36@ inclusive@ and suitable for use in automotive and related applications. Products included are bolts@ screws@ studs@ U-bolts@ preassembled screw and washer assemblies (sems)@ and products manufactured the same as sems except without washer. Products not covered are tapping screws@ thread-rolling screws@ and self-drilling screws@ Mechanical and material requirements for these products are covered in other SAE documents. The term stud as referred to herein@ applies to a cylindrical rod of moderate length@ threaded on either one or both ends or through its entire length. It does not apply to headed@ collard@ or similar products which are more closely characterized by requirements shown herein for bolts. For specification purpose@ this document treats U-bolts as studs. Thus@ wherever the word studs appear@ U-bolts is also implied. U-bolts covered by this documents are those used primarily in the suspension and related areas of vehicles@ (Designers should recognize that the U configuration may not sustain a load equivalent to two bolts ro studs of the same size and grade@ thus actual load-carrying capacity of U-bolts should be determined by saddle load tests.)