ANSI/IAS PRD 1-1998由SCC 发布于 1998-07-04。
。
ANSI/IAS PRD 1-1998 天然气汽车 (NGV) 燃料容器的泄压装置的最新版本是哪一版?
最新版本是 ANSI/IAS PRD 1-1998 。
This is a searchable PDF. 1. INTRODUCTION 1.1 General. This standard has been developed to identify performance requirements for pressure relief devices for Natural Gas Vehicle (NGV) fuel containers. This standard sets minimum requirements for pressure relief devices produced for use on NGV fuel containers. NGV fuel containers comply with ANSI/IAS NGV2, Basic Requirements for Compressed Natural Gas Vehicle (NGV) Fuel Containers [4], FMVSS 304, Federal Motor Vehicle Safety Standards, 49 CFR Part 571.304, Compressed Natural Gas Fuel Con tainer Integrity [2], and/or CSA B51, Part 2, High Pressure Cylinders for On-Board Storage of Natural Gas as a Fuel for Automotive Vehicles [5], as appropriate. These fuel containers are intended only for the on-board storage of high pressure compressed natural gas as a fuel for automotive vehicles to which the containers are permanently attached. Regulations and standards which apply to fuel container installation and vehicle systems include FMVSS 303, Federal Motor Vehicle Safety Standards, 49 CFR Part 571.303, Fuel System Integrity of Compressed Natural Gas Vehicles [1], CS 301.2, Transport Canada/TC, Motor Vehicle Safety Regulations, Schedule IV, CNG Fuel Sys tem Integrity [3], NFPA 52, Compressed Natural Gas (CNG) Vehicular Fuel Systems [6], and B149.4, Natural Gas for Vehicles Installation Code [7]. 1.2 Application. Natural Gas Vehicles use fuel containers categorized as follows: Type 1 (NGV2-1 or CNG-1) Metal; Type 2 (NGV2-2 or CNG-2) Resin impregnated continuous filament with metal liner of prescribed strength; Type 3 (NGV2-3 or CNG-3) Resin impregnated continuous filament wi th metal liner; Type 4 (NGV2-4 or CNG-4) Resin impregnated continuous filament with a non-metallic liner full wrapped. These fuel containers may accidentally be exposed to fire or elevated temperature. These conditions may act to increase the contained pressure and/or to degrade the structural materials, depending on the container type and materials of construction. A pressure relief device (PRD) will provide a means to vent the fuel container under these conditions.
(8)运送液化气的火车槽车、汽车槽车、贮罐等一般用内装式安全阀,如图4所示。 (9)油罐顶部一般用液压安全阀,需与呼吸阀配合使用。 (10)井下排水或天然气管道一般用先导式安全阀,如图6所示。 (11)液化石油气站罐泵出口的液相回流管道上一般用安全回流阀。 (12)负压或操作过程中可能会产生负压的系统一般用真空负压安全阀。 ...
(7)大口径,大排量及高压系统一般用脉冲式安全阀,如减温减压装置、电站锅炉等。(8)运送液化气的火车槽车、汽车槽车、贮罐等一般用内装式安全阀。(9)油罐顶部一般用液压安全阀,需与呼吸阀配合使用。(10)井下排水或天然气管道一般用先导式安全 阀。(11)液化石油气站罐泵出口的液相回流管道上一般用安全回流阀。(12)负压或操作过程中可能会产生负压的系统一般用真空负压安全阀。....
(8)运送液化气的火车槽车、汽车槽车、贮罐等一般用内装式安全阀。 (9)油罐顶部一般用液压安全阀,需与呼吸阀配合使用。 (10)井下排水或天然气管道一般用先导式安全阀。 (11)液化石油气站罐泵出口的液相回流管道上一般用安全回流阀。 (12)负压或操作过程中可能会产生负压的系统一般用真空负压安全阀。 ...
(8)运送液化气的火车槽车、汽车槽车、贮罐等一般用内装式安全阀,如图4所示。 (9)油罐顶部一般用液压安全阀,需与呼吸阀配合使用。 (10)井下排水或天然气管道一般用先导式安全阀,如图6所示。 (11)液化石油气站罐泵出口的液相回流管道上一般用安全回流阀。 (12)负压或操作过程中可能会产生负压的系统一般用真空负压安全阀。 ...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号