ANSI/ASTM D5677-2005
用于航空喷气机涡轮燃料的玻璃纤维(玻璃纤维加固热硬化树脂)管与管件规范.粘合剂粘接接头型

Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines

ANSI/ASTM D5677-2005 发布历史

This specification covers a reinforced plastic pipe and fittings system made from epoxy resin and glass-fiber reinforcement, together with adhesive for joint assembly, intended for service up to 150F (65.6C) and 150-psig (1034-kPa) operating pressure and surges up to 275 psig (1896 kPa) in aviation jet turbine fuel lines installed below ground. The dimensionless designator NPS has been substituted in this specification for such traditional terms as nominal diameter, size, and nominal size. The values stated in inch-pound units are to be regarded as standard. The values in parentheses are for information only. The following safety hazards caveat pertains only to the test method portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1There is no similar or equivalent ISO standard.

ANSI/ASTM D5677-2005由美国国家标准学会 US-ANSI 发布于 2005-11-29，并于 2005-11-29 实施。

ANSI/ASTM D5677-2005 在中国标准分类中归属于: E34 润滑油，在国际标准分类中归属于: 23.040.20 塑料管,23.040.45 塑料配件。

ANSI/ASTM D5677-2005的历代版本如下：

• 2005年11月29日 ANSI/ASTM D5677-2005 用于航空喷气机涡轮燃料的玻璃纤维(玻璃纤维加固热硬化树脂)管与管件规范.粘合剂粘接接头型

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 ANSI/ASTM D5677-2005 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

ANSI/ASTM D5677-2005

发布日期

2005年11月29日

实施日期

2005年11月29日

废止日期

无

中国标准分类号

E34

国际标准分类号

23.040.20;23.040.45

发布单位

US-ANSI

适用范围

This specification covers a reinforced plastic pipe and fittings system made from epoxy resin and glass-fiber reinforcement, together with adhesive for joint assembly, intended for service up to 150F (65.6C) and 150-psig (1034-kPa) operating pressure and surges up to 275 psig (1896 kPa) in aviation jet turbine fuel lines installed below ground. The dimensionless designator NPS has been substituted in this specification for such traditional terms as nominal diameter, size, and nominal size. The values stated in inch-pound units are to be regarded as standard. The values in parentheses are for information only. The following safety hazards caveat pertains only to the test method portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1There is no similar or equivalent ISO standard.