SIS SS IEC 463-1983
核检测仪表．用于放射线防护的便携式低能量X或γ射线照射量率计

Nuclear instrumentation - Low energy X or gamma radiation portable exposure r?te meters and monitors for use in radiological protection

SIS SS IEC 463-1983 发布历史

1.1 This recommendation applies to portable assemblies intended to measure exposure r?te due to X or gamma radiation of energy equal to or less than 60 keV for the purposes of radiation pro-tection, and which comprise at least: - a detector sub-assembly, (e.g., ionization chamber, G.M. counter tube, scintillation detector, etc), - a measuring sub-assembly, which may be connected together either rigidly or by means of a flexible cable, or incorporated into a single assembly. The recommendation applies only to those situations in which there is no beta radiation present at the point of measurement. 1.2 The recommendation is applicable in its entirety to the following assemblies defined in Clause 2 : - portable exposure r?te meters; - portable exposure r?te monitors. 1.3 The recommendation is also applicable to portable exposure r?te measuring assemblies designed for special applications (e.g. very high exposure r?tes). However, some of the specifications may need to be amended or supplemented according to the particular characteristics applicable to such assemblies. 1.4 If an assembly has been designed to carry out combined functions, it shall comply with the require-ments pertaining to each of these functions. If it has been designed to perform only one function, but is also capable of carrying out other functions, then it need comply only with the requirements for the first function. It would be desirable, however, for the assembly to meet the requirements pertaining to the other functions. 1.5 The requirements given below pertain to assemblies as defined in Sub-clause 1.1, and which are cur-rently being manufactured. It is possible, however, to use assemblies which do not meet the requirements set out below when such requirements are not deemed essential for a given purpose. In such cases, the requirements to be applied to the assemblies shall be specified by agreement between the manufacturer and the user, but the determination of the characteristics of the assemblies shall conform to the methods given in the present recommendations. 1.6 The recommendation is not applicable to the operating characteristics of the functional units or sub-assemblies for the display of information (e.g. indicating meters, recorders, alarms). The characteristics of such instruments shall be in conformity with the general specifications appro-priate to them. 1.7 This recommendation specifies, for the above described assemblies, general characteristics, general test procedures, radiation characteristics, electrical, mechanical, safety and environmental characteristics, and also the identification certificate.

SIS SS IEC 463-1983由SE-SIS 发布于 1983-5-20。

SIS SS IEC 463-1983的历代版本如下：

• 1983年05月20日 SIS SS IEC 463-1983 核检测仪表．用于放射线防护的便携式低能量X或γ射线照射量率计

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 SIS SS IEC 463-1983 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

SIS SS IEC 463-1983

发布日期

1983年05月20日

实施日期

废止日期

无

发布单位

SE-SIS

适用范围

1.1 This recommendation applies to portable assemblies intended to measure exposure r?te due to X or gamma radiation of energy equal to or less than 60 keV for the purposes of radiation pro-tection, and which comprise at least: - a detector sub-assembly, (e.g., ionization chamber, G.M. counter tube, scintillation detector, etc), - a measuring sub-assembly, which may be connected together either rigidly or by means of a flexible cable, or incorporated into a single assembly. The recommendation applies only to those situations in which there is no beta radiation present at the point of measurement. 1.2 The recommendation is applicable in its entirety to the following assemblies defined in Clause 2 : - portable exposure r?te meters; - portable exposure r?te monitors. 1.3 The recommendation is also applicable to portable exposure r?te measuring assemblies designed for special applications (e.g. very high exposure r?tes). However, some of the specifications may need to be amended or supplemented according to the particular characteristics applicable to such assemblies. 1.4 If an assembly has been designed to carry out combined functions, it shall comply with the require-ments pertaining to each of these functions. If it has been designed to perform only one function, but is also capable of carrying out other functions, then it need comply only with the requirements for the first function. It would be desirable, however, for the assembly to meet the requirements pertaining to the other functions. 1.5 The requirements given below pertain to assemblies as defined in Sub-clause 1.1, and which are cur-rently being manufactured. It is possible, however, to use assemblies which do not meet the requirements set out below when such requirements are not deemed essential for a given purpose. In such cases, the requirements to be applied to the assemblies shall be specified by agreement between the manufacturer and the user, but the determination of the characteristics of the assemblies shall conform to the methods given in the present recommendations. 1.6 The recommendation is not applicable to the operating characteristics of the functional units or sub-assemblies for the display of information (e.g. indicating meters, recorders, alarms). The characteristics of such instruments shall be in conformity with the general specifications appro-priate to them. 1.7 This recommendation specifies, for the above described assemblies, general characteristics, general test procedures, radiation characteristics, electrical, mechanical, safety and environmental characteristics, and also the identification certificate.