ASTM D5162-15
金属衬底上绝缘保护涂层不连续性 (漏涂) 测试的标准实施规程

Standard Practice for Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates

被代替

标准号

ASTM D5162-15

发布

2015年

发布单位

美国材料与试验协会

替代标准

ASTM D5162-21

当前最新

ASTM D5162-21

 

 

适用范围

4.1 A coating is applied to a metallic substrate to prevent corrosion, reduce abrasion or reduce product contamination, or all three. The degree of coating continuity required is dictated by service conditions. Discontinuities in a coating are frequently very minute and not readily visible. This practice provides a procedure for electrical detection of minute discontinuities in nonconductive coating systems.

4.2 Electrical testing to determine the presence and number of discontinuities in a coating film is performed on a nonconductive coating applied to an electrically conductive surface. The allowable number of discontinuities should be determined prior to conducting this test since the acceptable quantity of discontinuities will vary depending on coating film thickness, design, and service conditions.

4.3 The low voltage wet sponge test equipment is generally used for determining the existence of discontinuities in coating films having a total thickness of 0.5 mm (20 mil) or less. High voltage spark test equipment is generally used for determining the existences of discontinuities in coating films having a total thickness of greater than 0.5 mm (20 mil).

4.4 Coatings that are applied at a thickness of less than 0.5 mm (20 mil) may be susceptible to damage if tested with high voltage spark testing equipment. Consult the coating manufacturer for proper test equipment and inspection voltages.

4.5 To prevent damage to a coating film when using high voltage test instrumentation, total film thickness and dielectric strength in a coating system shall be considered in selecting the appropriate voltage for detection of discontinuities. Atmospheric conditions shall also be considered since the voltage required for the spark to gap a given distance in air varies with the conductivity of the air at the time the test is conducted. Suggested starting voltages are provided in Table 1.

Note 1: Alternative methods for selecting a suitable test voltage are given in Test Methods G62 and NACE RP0188, SP0274, and SP0490.

4.6 The coating manufacturer shall be consulted to obtain the following information, which would affect the accuracy of this test to determine discontinuities:

4.6.1 Establish the length of time required to adequately dry or cure the applied coating film prior to testing. Solvents retained in an uncured coating film may form an electrically conductive path through the film to the substrate.

4.6.2 Determine whether the coating contains electrically conductive fillers or pigments that may affect the normal dielectric properties.

4.7 This practice is intended for use with new coatings applied to metal substrates. Its use on a coating previously exposed to an immersion condition has often resulted in damage to the coating and has produced errone......

覆层的厚度测量

在化工，电子，电力，金属等行业中，为了实现对各类材料的保护或装饰作用，通常采用喷涂有色金属覆盖以及磷化、阳极氧化处理等方法，这样便出现了涂层、镀层、敷层、贴层或化学生成膜等概念，我们称之为“覆层”。　　覆层的厚度测量已成为金属加工工业已用户进行成品质量检测必备的zui重要工序。是产品达到优质标准的必备手段。...

涂层测厚仪的无损检测方法与原理

在化工，电子，电力，金属等行业中，为了实现对各类材料的保护或装饰作用，通常采用喷涂有色金属覆盖以及磷化、阳极氧化处理等方法，这样便出现了涂层、镀层、敷层、贴层或化学生成膜等概念，我们称之为“覆层”。　　覆层的厚度测量已成为金属加工工业已用户进行成品质量检测必备的zui重要工序。是产品达到优质标准的必备手段。...

磁性测量法及涡流测量法

在化工，电子，电力，金属等行业中，为了实现对各类材料的保护或装饰作用，通常采用喷涂有色金属覆盖以及磷化、阳极氧化处理等方法，这样便出现了涂层、镀层、敷层、贴层或化学生成膜等概念，我们称之为“覆层”。　　覆层的厚度测量已成为金属加工工业已用户进行成品质量检测必备的zui重要工序。是产品达到优质标准的必备手段。...

电容法

在化工，电子，电力，金属等行业中，为了实现对各类材料的保护或装饰作用，通常采用喷涂有色金属覆盖以及磷化、阳极氧化处理等方法，这样便出现了涂层、镀层、敷层、贴层或化学生成膜等概念，我们称之为“覆层”。　　覆层的厚度测量已成为金属加工工业已用户进行成品质量检测必备的zui重要工序。是产品达到优质标准的必备手段。...