13.030.20 液态废物、淤泥 标准查询与下载

HG/T 5365-2018 含锡废液处理处置方法

Treatment and disposal methods of tin-containing waste liquid

HG/T 5363-2018 含磷废液处理处置方法

Phosphorus-containing waste liquid treatment and disposal methods

ASTM F2283-12(2018) 船用油污染减排标准规范

1.1 This specification covers the design, manufacture, installation, performance, and operation of a shipboard oil pollution abatement system (OPAS) that collects, transfers, and processes all the oily waste generated from incidental operation of machinery spaces. This specification applies to commercial and public vessels and is intended for use by designers, manufacturers, purchasers, installers, and operators of shipboard OPAS to determine the requirements for system design, equipment manufacture, equipment purchase, system integration and installation, and system in-service operation. This specification and its supplementary sections may be tailored to meet the specific user’s needs to cover from OPAS new construction to retrofitting of individual OPAS equipment. 1.2 OPAS is comprised of drain tanks, bilge suctions, transfer pumps, Oily Bilge Water Holding Tanks, Oil Residue (sludge) Tanks, 15 ppm Bilge Separator systems, 15 ppm Bilge Alarm, automatic stopping device, and deck connections. The 15 ppm Bilge Separator is considered to be applicable for use to separate oily bilge water and ballast water from fuel oil tanks. Treatment of ballast water is addressed in other regulations/standards and is not addressed herein. 1.3 This specification covers the system from the point of entering the OPAS until the oil-water mixture is treated, the clean water meeting the applicable discharge limits is discharged overboard, and the separated oil is contained for on shore disposal or further treatment. It also includes concepts for minimizing oily waste generation. This specification is intended to augment the existing regulations, provide the user options to meet their specific needs, and should not be considered a replacement for overriding regulation. 1.4 It is recognized that the development and testing of high capacity separating equipment designed for dealing with effluent from cargo tanks on tankers pose special problems and such equipment is not required to be tested under International Maritime Organization (IMO) Marine Environment Protection Committee (MEPC) resolution MEPC.107 (49) nor is it covered in this specification 1.5 There are means to reduce the volume of bilge or process oily waste, or both, that are not considered 15 ppm Bilge Separators systems. Examples include incinerators, evaporators, combinations thereof, and other technologies. Such processes may require addressing all potential issues with the system such as toxicology and emissions to atmosphere. Such means or processes, or both, are out of scope of this specification. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Shipboard Oil Pollution Abatement System

IWA 28:2018 粪便污泥处理装置 - 能源独立 预制的社区规模资源回收装置 - 安全和性能

Faecal sludge treatment units — Energy independent, prefabricated, community-scale resource-recovery units — Safety and performance

IWA 28-2018 粪便污泥处理装置 能源独立、预制、社区规模的资源回收装置 安全和性能

Faecal sludge treatment units - Energy independent, prefabricated, community-scale resource-recovery units - Safety and performance

ASTM D8175-18 用Pensky-Martens闭杯试验仪测定液体废物的有限闪点的标准试验方法

1.1 This test method covers the procedure for a finite flash point test, within the range of 20 to 70 °C, of liquid wastes using a manual or automated Pensky-Martens closed cup tester. 1.2 This test method contains two procedures and is applicable to liquid waste, liquid phase(s) of multi-phase waste, liquid waste with suspended solids, or liquid waste that tends to form a surface film under test conditions. NOTE 1—If the liquid waste is of a viscosity such that the subsample volume will not be uniformly heated under the test conditions even with the increased stir rate of Procedure B, then use the small-scale method (Test Method D8174 for Finite Flash Point Determination of Liquid Wastes by Small-Scale Closed Cup Tester). 1.3 Procedure A is applicable to non-viscous liquids that are without suspended solids. Procedure B is applicable to viscous liquids, liquids with suspended solids, or liquids that form films. NOTE 2—This test method is not applicable for corrosive liquid wastes (see Test Method D8174). 1.4 Units—The values given in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning statements appear throughout. Also see applicable Safety Data Sheets (SDS) for information about certified reference materials (CRMs) or secondary working standards (SWSs) that may be used in the analysis. SDS may also be useful if some components of the waste sample are known. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Finite Flash Point Determination of Liquid Wastes by Pensky-Martens Closed Cup Tester

ASTM D8174-18 用小型闭杯试验仪测定液体废物的有限闪点的标准试验方法

1.1 This test method covers the procedure for a flash point test, within the range of –20 to 70 °C, of liquid wastes using a small-scale closed cup tester. NOTE 1—Some apparatus are not designed for subambient temperature tests, so the testing range would be between 20 °C and 70 °C. NOTE 2—This test method is not applicable for liquid waste that forms a surface film (see Test Method D8175 for Finite Flash Point Determination of Wastes by Pensky-Martens Closed Cup Tester). 1.2 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.3 This standard measures the ignitability properties of liquid wastes (which may be any discarded material), which may include secondary materials, off-specification products, and materials containing free liquids recovered during emergency response actions. Results from this test method may be used as part of a fire risk assessment of the material, but it is the responsibility of the user to perform any additional characterization needed for determination of storage, transport, treatment, or disposal per current regulations. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning statements appear throughout. See applicable Safety Data Sheets (SDS) for information about certified reference materials (CRMs) or secondary working standards (SWSs) that may be used in this test method. SDS may also be useful if some components of the waste sample are known. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Finite Flash Point Determination of Liquid Wastes by Small-Scale Closed Cup Tester

DB21/T 2943-2018 农村生活污水处理技术指南

Technical Guidelines for Rural Domestic Sewage Treatment

DB35/T 1728-2017 土壤环境损害鉴定评估技术方法

本标准规定了土壤环境损害鉴定评估的术语和定义、鉴定评估原则、鉴定评估一般要求、土壤环境损害调查与损害确定、因果关系分析、土壤环境损害实物量化、土壤环境损害价值量化、鉴定评估报告编制、恢复效果评估等内容。 本标准适用于因污染土壤环境（不含地下水）导致土壤环境损害的鉴定评。 本标准不适用于因核与辐射所致土壤环境损害的鉴定评估。

Soil Environmental Damage Identification and Evaluation Technical Method

ASTM F2363/F2363M-17 污水和灰水流过处理系统的标准规范

1.1 This specification covers the design, manufacture, performance, operation, and testing of flow through treatment systems intended to process sewage or graywater, or both, generated during a ship’s normal service. This specification is intended for use by designers, manufacturers, purchasers, and operators of shipboard environmental pollution control equipment to determine the requirements for equipment design, manufacture, purchase, and in-service operation. 1.2 The treatment system shall be capable of meeting the effluent requirements detailed in Section 4 with respect to a ship’s operational area. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Sewage and Graywater Flow Through Treatment Systems

HG/T 5206-2017 氟硅酸钠生产废液处理处置方法

Sodium fluorosilicate production waste liquid treatment and disposal methods

HG/T 5207-2017 化学镀镍废液处理处置方法

Chemical nickel plating waste liquid treatment and disposal methods

ASTM D7066-04(2017) 氯三氟乙烯（S-316）的二聚体/三聚体的标准测试方法红外测定可回收油和油脂和非极性材料

1.1 This test method covers the determination of oil and grease and nonpolar material in water and wastewater by an infrared (IR) determination of dimer/trimer of chlorotrifluoroethylene (S-316)2 extractable substances from an acidified sample. Included in this estimation of oil and grease are any other compounds soluble in the solvent. 1.2 This test method is applicable to measurement of the light fuel although loss of some light ends during extraction can be expected. 1.3 This test method defines oil and grease in water and wastewater as that which is extractable in the test method and measured by IR absorption at 2930 cm-1 or 3.4 microns. Similarly, this test method defines nonpolar material in water and wastewater as that oil and grease which is not adsorbed by silica gel in the test method and measured by IR absorption at 2930 cm-1 . 1.4 This test method covers the range of 5 to 100 mg/L and may be extended to a lower or higher level by extraction of a larger or smaller sample volume collected separately. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine (Guide D3856) the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination

T/GDES 10-2017 生态工业园区 电镀废水零排放技术规范 镀锌企业

1、生产工艺要求 2、镀锌工艺要求 3、锌的利用率 4、生产过程控制 5、企业废水分流 6、水的回用和补充

Technical requirements for zero discharge of electroplating wastewater in eco - industrial park（Galvanized enterprise）

T/GDES 9-2017 生态工业园区 电镀废水零排放技术规范 镀镍企业

1、镀镍工艺要求 2、镍的利用率 3、生产过程控制 4、企业废水分流 5、水的回用和补充

Technical requirements for zero discharge of electroplating wastewater in eco - industrial park（Galvanized enterprise）

T/GDES 8-2017 生态工业园区 电镀废水零排放 通用技术要求

1、生产企业废水分流 2、废水处理 3、废水的回用率 4、回用水的输出与使用 5、危险废物

General technical requirements for zero discharge of electroplating waste water in eco-industrial park

DIN EN 16720-1:2016 污泥特性描述. 物理一致性. 第1部分: 流动性测定. 挤压管装置法; 德文版本EN 16720-1-2016

Characterization of sludges - Physical consistency - Part 1: Determination of flowability - Method by extrusion tube apparatus; German version EN 16720-1:2016

DB35/T 1597-2016 温排水监测技术规范

本标准规定了温排水的监测方法、技术要求和自动监测设施的运营维护管理办法。 本标准适用于向江河、湖泊、水库、海域等具有使用功能的水体排放温水，导致表层水体温度升高的监测。

Technical specification for temperature and drainage monitoring

HG/T 5015-2016 含镍废液处理处置方法

本标准规定了含镍废液处理处置方法、环境保护和安全要求。 本标准适用于含镍废液的处理处置。

Treatment and disposal method for nickel waste liquid

BS EN 16720-1:2016 污泥特性描述. 物理一致性. 流动性测定. 挤压管装置法

Characterization of sludges. Physical consistency. Determination of flowability. Method by extrusion tube apparatus