13.340.10 防护服装 标准查询与下载

ISO 23616:2022 消防员个人防护装备（PPE）的清洁、检查和维修

This document gives requirements, guidance and recommendations for the cleaning, inspection, and repair of PPE for use by firefighters . This document is intended to be used by those responsible for the cleaning, inspections, and repair of firefighters PPE , however, it will also provide vital guidance to those who are responsible for establishing such a programme including fire and rescue services . This document does not cover the following at this time: a) chemical protective clothing; b) garments required for protection agains t chemical, biological, radiological and nuclear (CBRN ) materials .

Cleaning, inspection and repair of firefighters' personal protective equipment (PPE)

ASTM F2675/F2675M-22 确定电弧闪光保护用手保护产品的电弧额定值的标准试验方法

Standard Test Method for Determining Arc Ratings of Hand Protective Products Developed and Used for Electrical Arc Flash Protection

ASTM F2675/F2675M-22e1 确定电弧闪光保护用手保护产品的电弧额定值的标准试验方法

1.1 This test method is used to determine the arc rating of hand protective products in the form of gloves, glove materials, glove material systems, or other protective products designed to fit on the hand and specifically intended for electric arc flash protection use as protective accessories for workers exposed to electric arcs. The arc rating is determined in the test with an arc that has a heat flux value of 2100 kW/m2 [50 cal/cm2 /s]. 1.2 This test method will determine the arc rating of hand protective products made of materials that meet the following requirements for flame resistance: less than 150 mm [6 in.] char length, less than 2 s afterflame and no melt and drip when tested in accordance with Test Method D6413, receive a reported 50 % probability of ignition of a material or flammable underlayer (see definition of ignition50) by this method, or that have been evaluated and pass the ignition withstand requirements of this test method. 1.2.1 It is the intent of this test method to be used for hand protective products that are flame resistant or that have an adequate flame resistance for the required hazard (see 1.2). Non-flame resistant hand protective products may be used as under layers in multiple-layer systems or tested for ignition probability or ignition withstand. 1.2.2 Hand protective products tested by this test method are new and ratings received by this method may be reduced or eliminated by hydrocarbon loading (gasoline, diesel fuel, transformer oil, etc.), sweat, dirt, grease, or other contaminants. The end user takes responsibility for use of hand protective products tested by this method when contaminated in such a manner that could reduce or eliminate the arc rating of the hand protective products. 1.2.3 This test method is designed to provide information for gloves used for electric arc protection only. This test method is not suitable for determining electrical protective properties of hand protective products. 1.3 This test method is used to measure and describe the properties of hand protective products in response to convective and radiant energy generated by an electric arc under controlled laboratory conditions. 1.4 This test method does not apply to electrical contact or electrical shock hazards. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined 1.6 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment that takes into account all of the factors, which are pertinent to an assessment of the fire hazard of a particular end use. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautions, see Section 7. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the 1 This test method is under the jurisdiction of ASTM Committee F18 on Electrical Protective Equipment for Workers and is the direct responsibility of Subcommittee F18.65 on Wearing Apparel. Current edition approved April 1, 2022. Published May 2022. Originally approved in 2013. Last previous edition approved in 2021 as F2676/F2675M-21ɛ1 . DOI: 10.1520/F2675_F2675M-22E01. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Arc Ratings of Hand Protective Products Developed and Used for Electrical Arc Flash Protection

T/ZZB 2648-2022 职业用高可视性警示服

本文件规定了职业用高可视性警示服的术语和定义、 级别和设计要求、 号型、 基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存和质量承诺。 本文件适用于需要提高作业人员可视性以保障个人安全的各类岗位穿着的职业用高可视性警示服。

High visibility warning clothing for professional use

ASTM F1342/F1342M-05(2022) 防护服材料抗穿刺的标准试验方法

1.1 This test method determines the puncture resistance of a protective clothing material specimen by measuring the force required to cause a pointed puncture probe to penetrate through the specimen. This test method describes three protocols that may be used: Method A, Method B, and Method C. 1.1.1 Method A requires the use of Probe A only. The probe used for testing shall be recorded in the test report. 1.1.1.1 Probe A may be used to measure puncture resistance for the following types of materials: (1) Elastomeric materials, (2) Textiles, and (3) Coated materials. 1.1.2 Method B requires the use of Probe B. The probe used for testing shall be recorded in the test report. 1.1.2.1 Probe B may be used to measure puncture resistance for the following types of materials: (1) Textiles. (2) Coated materials. NOTE 1—Probe B is not suited for measuring the puncture resistance of unsupported elastomeric materials. 1.2 The values stated in SI units are to be regarded as the standard. The values in inch-pound units in brackets are for information purposes only. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Protective Clothing Material Resistance to Puncture

ASTM F2668-16(2022) 测定穿戴者对防护服套装的生理反应的标准实施规程

1.1 This practice specifies the test equipment and procedures for determining the physiological responses of subjects wearing a protective clothing ensemble. 1.2 This practice covers the physiological measurement of internal body core temperature, skin temperature, exposure time, heart rate response, oxygen consumption, and whole body sweat rate to assess the physiological responses of subjects wearing a protective clothing ensemble. This practice does not measure the musculoskeletal strain on the participant imposed by the protective clothing ensemble. 1.2.1 To increase safety during physiological testing, this dynamic test requires the use of human participants who meet specific health and physical fitness requirements. 1.3 The present standard does not attempt to determine important clothing characteristics, such as thermal insulation and evaporative resistance of the protective clothing ensemble. Test Methods F1291 and F2370 can be used for these clothing measurements. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 It is the responsibility of the test laboratory to obtain the necessary and appropriate approval(s) required by their institution for conducting tests using human participants. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determining the Physiological Responses of the Wearer to Protective Clothing Ensembles

ASTM F3050-22 个人防护服和设备合格评定的标准指南

Standard Guide for Conformity Assessment of Personal Protective Clothing and Equipment

BS EN ISO 15384:2020+A1:2021 消防员的防护服 野外消防服实验室测试方法及性能要求

What is ISO 15384+A1 about? ISO 15384+A1 is an international standard on test methods and requirements for wildland firefighting clothing to improve the efficacy of protective clothing. ISO 15384+A1 specifies methods of test and minimum performance requirements for personal protective clothing, designed to protect the wearer’s body, except for the head, hands, and feet, that is worn during wildland firefighting and associated activities. ISO 15384+A1 covers the general design of the garment, the minimum level of performance for the materials employed and the methods of test to determine these levels. Note: ISO 15384+A1 is not applicable to clothing for use in situations encountered in structural firefighting, rescue or where an elevated level of infrared radiation is expected. ISO 15384+A1 does not provide protection against high mechanical risks such as for protection when using chain saws. Who is ISO 15384+A1 for ? ISO 15384+A1 on protective clothing for firefighters is useful for: Protective clothing manufacturers Protective clothing testers Protective clothing designers Safety and health departments Risk management departments Why should you use ISO 15384+A1 ? Wildland firefighting involves work primarily in summer temperatures, for many hours in which the firefighter can develop prominent levels of metabolic heat. ISO 15384+A1 helps you by providing the test methods and performance requirements for wildland firefighting clothing to prevent them from serious burn injury. The test methods and performance requirements provided by

Protective clothing for firefighters. Laboratory test methods and performance requirements for wildland firefighting clothing

ASTM F1359/F1359M-22 人体模型上淋浴喷头下防护服或防护套耐液体渗透性的标准试验方法

1.1 This test method measures the ability of protective clothing or protective ensembles to resist liquid penetration in the form of a shower spray with surfactant-treated water. 1.2 This test method measures the liquid penetration resistance of the construction and configuration of the overall protective clothing or protective ensemble, but especially of seams, closures, and interfaces with other components such as gloves, boots, hoods, and respiratory protective equipment. It is intended that this test method be used to assess the liquid penetration resistance of protective clothing and protective ensembles as received from the manufacturer and worn in accordance with their instructions. 1.3 Resistance of materials used in protective clothing to permeation or penetration can be determined in accordance with Test Method F739 (or Test Method F1383 or F1407) and Test Method F903, respectively. Alternatively, resistance of materials used in protective clothing to penetration by synthetic blood or liquids containing virus can be determined in accordance with Test Methods F1670/F1670M and F1671/F1671M. 1 This test method is under the jurisdiction of ASTM Committee F23 on Personal Protective Clothing and Equipment and is the direct responsibility of Subcommittee F23.30 on Chemicals. Current edition approved Jan. 1, 2022. Published January 2022. Originally approved in 1991. Last previous edition approved in 2016 as F1359/F1359M – 16a. DOI: 10.1520/F1359_F1359M-22. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.4 The integrity of vapor protective ensembles is measured by its ability to maintain positive internal pressure with Test Method F1052. 1.5 The values in SI units or in other units shall be regarded separately as standard. The values stated in each system must be used independently of the other, without combining values in any way. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Liquid Penetration Resistance of Protective Clothing or Protective Ensembles Under a Shower Spray While on a Manikin

T/ZSA 86-2021 纳米自洁抑菌口罩

本文件规定了纳米自洁抑菌口罩的要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于由纳米自洁抑菌涂层制成的，在日常及医疗环境下，滤除细菌及病毒的防护型口罩。 本文件不适用于在有害气体及有毒液体的蒸汽环境下，在缺氧、水下作业等环境下使用的呼吸防护用品。

Self-cleaning bacteriostatic nanomaterials mask

T/ZSA 85-2021 纳米防雾抑菌拭镜布

本文件规定了纳米防雾抑菌拭镜布的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以纳米亲水材料制成的防雾拭镜布。

Anti-fogging Bacteriostatic Nano-materials wiping cloth

ASTM F955-15(2021) 评估防护服材料与熔融物质接触时热传递的标准试验方法

1.1 This test method covers the evaluation of materials’ thermal resistance to heat transfer when exposed to a molten substance pour. 1.1.1 This test method was validated using molten substances of aluminum, brass, and iron. The test shall be permitted to be adapted for use with other substances. 1.2 This test method is applicable to materials from which finished primary protective apparel articles are made. 1.3 This test method does not measure the flammability of materials, nor is it intended for use in evaluating materials exposed to any other thermal exposure. 1.4 Use this test method to measure and describe the properties of materials, products, or assemblies in response to molten substance pour under controlled laboratory conditions and shall not be used to describe or appraise the thermal hazard or fire risk of materials, products, or assemblies under actual conditions. However, it is acceptable to use results of this test as elements of a thermal risk assessment which takes into account all the factors that are pertinent to an assessment of the thermal hazard of a particular end use. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 8. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluating Heat Transfer Through Materials for Protective Clothing Upon Contact with Molten Substances

ASTM F2675/F2675M-21 确定电弧闪光保护用手保护产品的电弧额定值的标准试验方法

Standard Test Method for Determining Arc Ratings of Hand Protective Products Developed and Used for Electrical Arc Flash Protection

ASTM F2703-21 具有烧伤预测的服装用阻燃材料的非稳态传热评估的标准试验方法

1.1 This test method measures the non-steady state heat transfer through flame-resistant materials for clothing subjected to a combined convective and radiant heat exposure. 1.1.1 This test method is not applicable to materials that are not flame resistant. NOTE 1—The determination of a material’s flame resistance shall be made prior to testing and done in accordance with the applicable performance or specification standard, or both, for the material’s end use. 1.1.2 This test method accounts for the thermal energy contained in an exposed test specimen after the standardized combined convective and radiant heat exposure has ceased and is used to estimate performance to a predicted second-degree skin burn injury. 1.2 This test method is used to measure and describe the response of materials, products, or assemblies to heat under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound or other units that are commonly used for thermal testing. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame-Resistant Materials for Clothing with Burn Injury Prediction

OENORM EN 4863-2021 航空航天系列旋翼机救生服要求、试验和标志

Aerospace series - Rotorcraft immersion suits - Requirements, testing and marking

ASTM F1002-15(2021) 暴露于特定熔融物质和相关热危害的工人使用的防护服和材料的标准性能规范

1.1 This performance specification establishes the minimum design and performance requirements for protective clothing and protective clothing materials for both primary and secondary protection from exposure to molten substances and related thermal hazards. 1.2 This performance specification is not intended to address protection from hot liquids or from specialized forms of heat and flame protection such as any fire fighting application. 1.3 This performance specification describes the properties of specific textile materials in their material or garment composite form as tested by laboratory methods and is not intended to be used to appraise the thermal hazard or risk under actual conditions. However, it is acceptable to use information on the thermal performance of clothing made from textile materials conforming to this specification as an element in thermal risk assessment which takes into account all factors pertinent to the thermal hazard of a particular end use. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.5 This performance specification does not purport to address all of the safety concerns, if any, associated with the use of compliant protective clothing or protective clothing materials. It is the responsibility of the persons or organizations that use this performance specification to conduct a hazard and risk assessment to determine the applicability of this performance specification to the intended application of the protective clothing or protective clothing materials, and to establish appropriate safety, health, and environmental practices. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Performance Specification for Protective Clothing and Materials for Use by Workers Exposed to Specific Molten Substances and Related Thermal Hazards

DS/EN ISO 15384:2021 消防员防护服《野外消防服实验室测试方法和性能要求》修正案1（ISO 15384:2018/Amd 1:2021）

Protective clothing for firefighters – Laboratory test methods and performance requirements for wildland firefighting clothing – Amendment 1 (ISO 15384:2018/Amd 1:2021)

KS K ISO 12127-2-2021 防热阻燃服装 通过防护服或构成材料接触传热的测定 第2部分：利用小圆柱体跌落产生接触热的试验方法

Clothing for protection against heat and flame－Determination of contact heat transmission through protective clothing or constituent materials－Part 2：Test method using contact heat produced by dropping small cylinders

KS K ISO 9185-2021 防护服 材料抗熔融金属飞溅性能的评定

Protective clothing－Assesment of resistance of materials to molten metal splash

KS G 6805-2021 安全头盔

Safety helmets