13.340.10 防护服装 标准查询与下载

GSO EN 17092-3:2023 摩托车骑手防护服 第3部分：AA 级服装 要求

This document specifies general requirements for motorcyclists’ protective garments of Class AA: protective garments, which are intended to provide limited protection to the wearer against abrasion and impact injury. It applies to protective garments for motorcycle on-road use.

Protective garments for motorcycle riders - Part 3: Class AA garments - Requirements

GSO ISO/TR 21808:2023 旨在为消防员提供保护的个人防护装备 (PPE) 的选择、使用、保养和维护指南

This document sets out guidance for the selection, use, care and maintenance of PPE designed to provide protection for firefighters while carrying out their duties. The PPE covered in this document is intended for firefighting personnel exposed to risks associated with but not necessarily limited to the following activities: — structural firefighting; — wildland firefighting; — incidents involving hazardous materials; — incidents involving motor vehicle; — urban search and rescue. The purpose of this document is to highlight the main areas that a Fire service needs to consider when providing PPE to its members. This document is a supplement to the information provided in the PPE standards or used in conjunction with them. Most paragraphs of the document contain bulletlists, these lists are provided for guidance only and they are not exhaustive.

Guidance on the selection, use, care and maintenance of personal protective equipment (PPE) designed to provide protection for firefighters

GSO ISO 19918:2023 防护服 化学品防护 低蒸气压化学品透过材料累积渗透的测量

ISO 19918 describes laboratory test methods to determine the resistance of materials, closures, and seams used in personal protective equipment (PPE) to permeation by solid or liquid chemicals with low vapour pressure (less than 133,322 Pa at 25 °C) and/or insolubility in water or other liquids commonly used as collection media. These chemicals that are often part of pesticide formulations and other mixtures cannot be measured using other standards for measuring permeation. This test method is suitable for field strength and concentrated pesticide formulations as well as other mixtures in which the active ingredient is a chemical with low vapour pressure and/or low solubility in commonly used liquid and gaseous collection media. This test method is not intended to be used in place of standards such as ISO 6529, EN 16523-1 and ASTM F739, which measure permeation of chemicals that are either volatile or soluble in water or other liquids that do not interact with the material being tested. ISO 19918 is not suitable for measurement of volatile chemicals that may evaporate before the chemical analysis is complete. The degree of contamination depends on numerous factors, such as type of exposure, application technique, and chemical formulation. As the level of exposure can vary considerably, this method is designed to rate relative performance of PPE materials for different durations. This method is designed to measure cumulative permeation. Breakthrough time cannot be measured by this method. This test method does not measure resistance to penetration or degradation. The test method standard may be used for the evaluation of PPE materials that are new or those for which the product standard requires treatment, such as laundering or simulated abrasion. Details of the treatment shall be reported.

Protective clothing — Protection against chemicals — Measurement of cumulative permeation of chemicals with low vapour pressure through materials

T/CMISHA 2003-2023 摩托车乘员防护服装技术规范

本文件规定了摩托车乘员防护服装的分类和要求，描述了相应的检测方法，规定了标志、包装、运输和贮存要求。

Technical specification for motorcyclists' protective clothing

ASTM F1937-04(2023) 马匹运动和骑马用身体保护器的标准规范

1.1 This specification covers minimum performance criteria and describes test methods for body protectors for use in horse sports and horseback riding. 1.2 It is not the intention of this specification to bar from consideration materials of improved quality or performance not known at the time of development of this specification. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Body Protectors Used in Horse Sports and Horseback Riding

ASTM F2992-23 用扭矩计测试设备测量防护服用材料耐切割性的标准测试方法

1.1 This test method covers the measurement of the cut resistance of a material when mounted on a specimen holder and subjected to a cutting edge under a specified load using a tomodynamometer.2 1.1.1 This procedure is not valid for high-porosity materials which allow cutting edge contact with the mounting surface prior to cutting. 1.1.2 Test apparatus may have limitations in testing materials with a thickness greater than 20 mm. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Cut Resistance of Materials Used in Protective Clothing with Tomodynamometer Test Equipment

23/30431371 DC BS EN ISO 13506-1 耐热和火焰防护服 第 1 部分：整套服装的测试方法 使用仪器化人体模型测量传输能量

BS EN ISO 13506-1. Protective clothing against heat and flame - Part 1. Test method for complete garments. Measurement of transferred energy using an instrumented manikin

23/30431377 DC BS EN ISO 13506-2 耐热和火焰防护服 第 2 部分 皮肤烧伤预测 计算要求和测试用例

BS EN ISO 13506-2. Protective clothing against heat and flame - Part 2. Skin burn injury prediction. Calculation requirements and test cases

23/30431396 DC BS EN ISO 24232 防护服 防雨

BS EN ISO 24232. Protective clothing. Protection against rain

T/CAS ES180102001-2022 工业品质量分级评价规则 防静电服

1　范围 本文件规定了防静电服质量分级的评价程序和要求、评价方法、质量分级等内容。 本文件适用于防静电服质量分级评价活动。 2　规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB/T 2912.1  纺织品 甲醛的测定 第1部分：游离水解的甲醛（水萃取法） GB/T 3917.3  纺织品 织物撕破性能 第3部分：梯形试样撕破强力的测定 GB/T 3922  纺织品 色牢度试验 耐汗渍色牢度 GB/T 3923.1  纺织品 织物拉伸性能 第1部分：断裂强力和扯断伸长率的测定（条样法） GB/T 5453  纺织品 织物透气性的测定 GB/T 5713  纺织品 色牢度试验 耐水色牢度 GB/T 7573  纺织品 水萃取液pH值的测定 GB/T 8427  纺织品 色牢度试验 耐人造光色牢度：氙弧   GB/T 8628  纺织品 测定尺寸变化的试验中织物试样和服装的准备、标记及测量 GB/T 8629  纺织品 试验用家庭洗涤和干燥程序 GB/T 8630  纺织品 洗涤和干燥后尺寸变化的测定 GB/T 11048  纺织品 生理舒适性 稳态条件下热阻和湿阻的测定（蒸发热板法） GB 12014  防护服装 防静电服 GB/T 14272  羽绒服装 GB/T 17592  纺织品 禁用偶氮染料的测定 GB/T 18318.1  纺织品 弯曲性能的测定 第1部分：斜面法 GB 18401  国家纺织产品基本安全技术规范 T/CAS ES000000001—2022（V01） 工业品质量分级评价规则 通则 Q/SH 0587.1-5  劳动保护服装技术要求

Rules for quality grading and evaluating of industrial products—Static protective clothing

23/30463014 DC BS EN 14325:2018/A1 化学品防护服 化学防护服材料、接缝、连接处和组合件的试验方法和性能分类

BS EN 14325:2018/A1. Protective clothing against chemicals. Test methods and performance classification of chemical protective clothing materials, seams, joins and assemblages

KS K ISO 18639-3:2022 从事特定救援活动的消防员用PPE防护服.第3部分:服装

PPE ensembles for firefighters undertaking specific rescue activities — Part 3: Clothing

KS K ISO 18640-1-2022 消防员防护服.生理影响.第1部分:与出汗躯干耦合的热和湿传递的测量

Protective clothing for firefighters — Physiological impact — Part 1: Measurement of coupled heat and moisture transfer with the sweating torso

KS K ISO 18639-3-2022 从事特定救援活动的消防员用PPE防护服.第3部分:服装

PPE ensembles for firefighters undertaking specific rescue activities — Part 3: Clothing

KS K ISO 18640-2-2022 消防员防护服.生理影响.第2部分:消防员穿戴防护服引起的生理热负荷的测定

Protective clothing for firefighters — Physiological impact — Part 2: Determination of physiological heat load caused by protective clothing worn by firefighters

KS K ISO 18640-2:2022 消防员防护服.生理影响.第2部分:消防员穿戴防护服引起的生理热负荷的测定

Protective clothing for firefighters — Physiological impact — Part 2: Determination of physiological heat load caused by protective clothing worn by firefighters

KS K ISO 18640-1:2022 消防员防护服.生理影响.第1部分:与出汗躯干耦合的热和湿传递的测量

Protective clothing for firefighters — Physiological impact — Part 1: Measurement of coupled heat and moisture transfer with the sweating torso

KS K 7807-2022 防止静电危害的工作服

Working wears for preventing electrostatic hazards

T/ZZB 2955-2022 日常用高可视性服装

本文件规定了日常用高可视性服装的术语和定义、号型、分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存、使用说明、质量承诺。 本文件适用于以纺织织物为主要原料生产的，在日常生活中为提升其视觉可见性而穿着的服装。 本文件不适用于 36 个月及以下的婴幼儿服装。 本文件不适用于职业用高可视性警示服。

High visibility clothing for daily use

ASTM F2320-18(2022) 橡胶绝缘薄板标准规范

1.1 This specification covers testing of rubber insulating sheeting for use as a covering for the protection of workers from accidental contact with live electrical conductors, apparatus, or circuits. 1.2 Two types of sheeting, differing in chemical and physical characteristics, are provided and are designated as Type I, non-resistant to ozone and Type II, resistant to ozone. 1.3 Three classes of sheeting, differing in electrical protection characteristics are provided and designated as Class 00, Class 0, and Class 1. 1.4 Two styles of sheeting, differing in construction characteristics, are provided and are designated as Style A and Style B. 1.5 The follow safety hazards caveat applies only to the test method portion, Sections 17 – 19, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Rubber Insulating Sheeting should remain flexible for use through normal temperature ranges. NOTE 2—Rubber as used in this specification is a generic term that includes elastomers and elastomeric compounds, regardless of origin. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Rubber Insulating Sheeting