13.340.10 防护服装 标准查询与下载

23/30374608 DC BS EN ISO 17491-4 防护服 化学品防护服装的试验方法 第 4 部分：液体喷雾抗渗透性的测定（喷雾试验）

BS EN ISO 17491-4. Protective clothing. Test methods for clothing providing protection against chemicals - Part 4. Determination of resistance to penetration by a spray of liquid (spray test)

ASTM F1868-23 使用发汗热板测量服装材料的热阻、蒸发阻力和总热损失的标准试验方法

1.1 This test method covers the measurement of the thermal resistance, evaporative resistance, and total heat loss under steady-state conditions of fabrics, films, coatings, foams, and leathers, including multi-layer assemblies, for use in clothing systems. 1.2 The range of this measurement technique for intrinsic thermal resistance is from 0.002 to 0.5 K·m2 /W and for intrinsic evaporative resistance is from 0.0 to 1.0 kPa·m2 /W. The total heat loss range is from 0.0 to 1300 W/m2 . 1.3 The values in SI units shall be regarded as standard. Other units of measurement are provided in this standard but are not regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Thermal Resistance, Evaporative Resistance, and Total Heat Loss Measurements of Clothing Materials Using a Sweating Hot Plate

ASTM F1296-08(2023) 化学防护服评定标准指南

1.1 This guide is intended to aid in the application of standards for the development, specification, and selection of chemical protective clothing with the ultimate goal of maintaining the safety and health of workers who come into contact with hazardous chemicals. 1.2 This guide provides a short description of each referenced standard and then makes specific recommendations for the use of these standards. The referenced standards are organized under the following headings: Material Chemical Resistance, Material Physical Properties, Seam and Closure Performance, and Overall Clothing Performance. 1.3 No protocol can ensure the selection of protective clothing that guarantees worker protection. The purpose of testing is to generate data and information that will allow the selection of the most appropriate clothing. Ultimately, clothing selection is based on technical evaluation of available information and professional assessment of risk. 1.4 The values stated in SI units or in other units shall be regarded separately as standard. The values stated in each system must be used independently of the other, without combining values in any way. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Evaluating Chemical Protective Clothing

23/30463700 DC BS ISO 11999-1 消防员的个人防护装备 扑救建筑物内发生的火灾时面临暴露于高热和/或火焰风险的消防员所使用的个人防护装备的测试方法和要求 第 1 部分：概述

BS ISO 11999-1. PPE for firefighters. Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures - Part 1. General

ASTM F1930-23 使用仪表人体模型进行火灾模拟评估阻燃服装的标准测试方法

1.1 This test method is used to provide predicted human skin burn injury for single-layer garments or protective clothing ensembles mounted on a stationary upright instrumented manikin which are then exposed in a laboratory to a simulated fire environment having controlled heat flux, flame distribution, and duration. The average exposure heat flux is 84 kW/m2 (2 cal ⁄s·cm2 ), with durations up to 20 s. 1.2 The visual and physical changes to the single-layer garment or protective clothing ensemble are recorded to aid in understanding the overall performance of the garment or protective clothing ensemble and how the predicted human skin burn injury results can be interpreted. 1.3 The skin burn injury prediction is based on a limited number of experiments where the forearms of human subjects were exposed to elevated thermal conditions. This forearm information for skin burn injury is applied uniformly to the entire body of the manikin, except the hands and feet. The hands and feet are not included in the skin burn injury prediction. 1.4 The measurements obtained and observations noted can only apply to the particular garment(s) or ensemble(s) tested using the specified heat flux, flame distribution, and duration. 1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.6 This method is not a fire test response test method. 1.7 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units or other units commonly used for thermal testing. If appropriate, round the non-SI units for convenience. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluation of Flame-Resistant Clothing for Protection Against Fire Simulations Using an Instrumented Manikin

ASTM F2053-00(2023) 防护服材料的空气颗粒渗透试验结果记录的标准指南

1.1 This guide provides a format for documenting information and performance data for an airborne particle penetration test. 1.2 Documented data and information are grouped into five categories that define important aspects of each test: 1.2.1 Description of material tested, 1.2.2 Challenge particles, 1.2.3 Test method, 1.2.4 Test results, and 1.2.5 Source of the data. 1.3 Use of this guide is facilitated by adherence to procedures outlined in a standard test method. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurements are included in this standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Documenting the Results of Airborne Particle Penetration Testing of Protective Clothing Materials

ISO 13997:2023 防护服机械性能耐尖锐物体切割性能的测定

Protective clothing — Mechanical properties — Determination of resistance to cutting by sharp objects

ISO/CD 22615:2023 防护服 防护服性能要求和测试方法

Protective clothing — Performance requirements and test methods for protective clothing against infective agents

ISO/DIS 11999-4:2023 消防员个人防护装备 在扑灭建筑物内发生的火灾时面临暴露于高热和/或火焰风险的消防员使用的个人防护装备的测试方法和要求 第 4 部分：手套

PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 4: Gloves

ISO/DIS 14116:2023 防护服 火焰防护 有限火焰蔓延材料、材料组件和服装

Protective clothing — Protection against flame — Limited flame spread materials, material assemblies and clothing

ISO 11610:2023 防护服.词汇

This document contains a list of terms which are frequently used in the standardization of protective clothing (5.1.4) and protective equipment worn on the body, including hand and arm protection and lifejackets, and definitions of these terms. The definitions are intended to support an unambiguous use of the terms listed. This document is intended to serve as a reference document for the Working Groups of CEN/TC 162 and ISO/TC 94/SC 13 to ascertain what definitions already exist and may be used for setting up new standards and to provide guidance in the elaboration of new definitions.

Protective clothing — Vocabulary

23/30393153 DC BS EN ISO 15027-3 救生服 第 3 部分：测试方法

BS EN ISO 15027-3. Immersion suits - Part 3. Test methods

23/30393150 DC BS EN ISO 15027-2 救生服 第 2 部分：遗弃服 包括安全在内的要求

BS EN ISO 15027-2. Immersion suits - Part 2. Abandonment suits, requirements including safety

23/30393147 DC BS EN ISO 15027-1 救生服 第 1 部分：常穿救生衣 包括安全在内的要求

BS EN ISO 15027-1. Immersion suits - Part 1. Constant wear suits, requirements including safety

GSO EN 17092-1:2023 摩托车驾驶员防护服 第1部分：测试方法

This document describes some of the test methods for use with EN 17092 protective garments for motorcycle riders (Part 2 and following parts). It describes the appropriate test methods for zoning, ergonomics, mechanical properties and impact abrasion resistance.

Protective garments for motorcycle riders - Part 1: Test methods

GSO EN 17092-5:2023 摩托车骑手防护服 第5部分：B 类服装 要求

This European Standard specifies general requirements for motorcyclists’ protective garments of Class B: protective garments, which are intended to provide limited protection to the wearer against abrasion injury. It applies to protective garments for motorcycle on-road use.

Protective garments for motorcycle riders - Part 5: Class B garments - Requirements

GSO ISO 19918:2023 防护服 化学品防护 低蒸气压化学品透过材料累积渗透的测量

ISO 19918 describes laboratory test methods to determine the resistance of materials, closures, and seams used in personal protective equipment (PPE) to permeation by solid or liquid chemicals with low vapour pressure (less than 133,322 Pa at 25 °C) and/or insolubility in water or other liquids commonly used as collection media. These chemicals that are often part of pesticide formulations and other mixtures cannot be measured using other standards for measuring permeation. This test method is suitable for field strength and concentrated pesticide formulations as well as other mixtures in which the active ingredient is a chemical with low vapour pressure and/or low solubility in commonly used liquid and gaseous collection media. This test method is not intended to be used in place of standards such as ISO 6529, EN 16523-1 and ASTM F739, which measure permeation of chemicals that are either volatile or soluble in water or other liquids that do not interact with the material being tested. ISO 19918 is not suitable for measurement of volatile chemicals that may evaporate before the chemical analysis is complete. The degree of contamination depends on numerous factors, such as type of exposure, application technique, and chemical formulation. As the level of exposure can vary considerably, this method is designed to rate relative performance of PPE materials for different durations. This method is designed to measure cumulative permeation. Breakthrough time cannot be measured by this method. This test method does not measure resistance to penetration or degradation. The test method standard may be used for the evaluation of PPE materials that are new or those for which the product standard requires treatment, such as laundering or simulated abrasion. Details of the treatment shall be reported.

Protective clothing — Protection against chemicals — Measurement of cumulative permeation of chemicals with low vapour pressure through materials

GSO EN 17092-6:2023 摩托车骑手防护服 第6部分：C 级服装 要求

This document specifies general requirements for motorcyclists’ protective garments of Class C, worn as under or overgarments, intended to provide limited protection to the wearer against impact injury. It applies to protective garments for motorcycle on-road use.

Protective garments for motorcycle riders - Part 6: Class C garments - Requirements

GSO EN 17092-2:2023 摩托车骑手防护服 第2部分：AAA 级服装 要求

This document specifies general requirements for motorcyclists’ protective garments of Class AAA: protective garments, which are intended to provide limited protection to the wearer against abrasion and impact injury. It applies to protective garments for motorcycle on-road use.

Protective garments for motorcycle riders - Part 2: Class AAA garments - Requirements

GSO EN 17092-3:2023 摩托车骑手防护服 第3部分：AA 级服装 要求

This document specifies general requirements for motorcyclists’ protective garments of Class AA: protective garments, which are intended to provide limited protection to the wearer against abrasion and impact injury. It applies to protective garments for motorcycle on-road use.

Protective garments for motorcycle riders - Part 3: Class AA garments - Requirements