17.100 力、重力和压力的测量 标准查询与下载

ASTM F2070-00(2022) 压力传感器、压差传感器、压力传感器、电气传感器和光纤传感器

1.1 This specification covers the requirements for pressure and differential pressure transducers for general applications. 1.2 Special requirements for naval shipboard applications are included in Supplementary Requirements S1, S2, and S3. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. Where information is to be specified, it shall be stated in SI units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Transducers, Pressure and Differential, Pressure, Electrical and Fiber-Optic

ASTM F3109-22 多轴测力平台验证的标准实施规程

1.1 This standard recommends practices for performance verification of multi-axis force platforms commonly used for measuring ground reaction forces during gait, balance, and other activities. 1.1.1 This standard provides a method to quantify the relationship between applied input force and force platform output signals across the manufacturer’s defined spatial working surface and specified force operating range. 1.1.2 This standard provides definitions of the critical parameters necessary to quantify the behavior of multi-axis force measuring platforms and the methods to measure the parameters. 1.1.3 This standard presents methods for the quantification of spatially distributed errors and absolute measuring performance of the force platform at discrete spatial intervals and discrete force levels on the working surface of the platform. 1.1.4 This standard further defines certain important derived parameters, notably COP (center of pressure) and methods to quantify and report the measuring performance of such derived parameters at spatial intervals and force levels across the working range of the force platform. 1.1.5 This standard defines the requirements for a report suitable to characterize the force platform’s performance and provide traceable documentation to be distributed by the manufacturer or calibration facility to the users of such platforms. 1.1.6 Dynamic characteristics and applications where the force platform is incorporated in other equipment, such as instrumented treadmills and stairs, are beyond the scope of this standard. 1.1.7 This standard is written for purposes of multi-axis force platform verification. However, the methods and procedures are applicable to calibration of force platforms by manufacturers. 1.2 The values stated in SI units are to be regarded as the standard. Other metric and inch-pound values are regarded as equivalent when required. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Verification of Multi-Axis Force Measuring Platforms

T/CWIAS 0001.1-2022 集装箱超偏载检测仪第一部分: 平台式

本文件规定了平台式集装箱超偏载检测仪（以下简称：检测仪）产品的术语和定义、规格和型号、计量要求、技术要求、试验方法、检验规则和标志、包装、运输和贮存

Detecting instrument for overload and unbalanced load of freight container— Part 1: Platform type

T/ZSM 0005-2022 电子计价秤欺骗性使用特征与判定

本标准共有6部分内容：1 范围；2 规范性引用文件；3 术语和定义；4 技术要求；5 试验方法；6 判定规则。 主要内容可归纳为：2231，即“两个关键定义”、“两个重要关联”，“三个典型特征”、“一个重要试验方法”。 两个关键定义：（1）欺骗性使用——通过操作者的主观意识，实施对称重结果或货物总价的调整，破坏电子计价秤准确度，达到欺骗消费者目的的过程；（2）欺骗性使用特征——电子计价秤自身具有的软、硬件特征，使得操作者容易进行欺骗性使用。 两个重要关联：（1）将欺骗性使用和作弊活动关联；（2）将欺骗性使用特征和作弊特征关联。 三个典型欺骗性使用特征：（1）软件密码方式。输入密码进行欺骗性使用的模式，可以按照预设的方式调整称重结果。关机后再次重新开机或特定按键退出，又恢复正常称重模式，不再具有可调整称重结果的状况；（2）硬件电路改装。通过改装电子计价秤硬件电路，按照预设的方式，在电子计价秤上调整称重结果。通过改装电子计价秤硬件电路，增加无线传输的接收信号装置，按照预定的方式，在电子计价秤外部遥控调整称重结果，这也是硬件电路改装的一种方式。（3）同时具备硬件电路改装和软件密码方式 一个重要试验方法：考虑到可能存在软件密码方式，在电子计价秤关机后无法复现欺骗性使用特征的情况，对于现场检测到，并保存有完好视频录像的测试过程，也默认为试验活动。

Characters and judgment of fraudulent use on electronic price computing scale

GSO ASTM E74:2022 测力仪器校准和验证的标准实践

1.1 The purpose of these practices is to specify procedures for the calibration of force-measuring instruments. Procedures are included for the following types of instruments: 1.1.1 Elastic force-measuring instruments, and 1.1.2 Force-multiplying systems, such as balances and small platform scales. NOTE 1: Verification by deadweight loading is also an acceptable method of verifying the force indication of a testing machine. Tolerances for weights for this purpose are given in Practices E4; methods for calibration of the weights are given in NIST Technical Note 577(1)2, Methods of Calibrating Weights for Piston Gages. 1.2 The values stated in SI units are to be regarded as the standard. Other metric and inch-pound values are regarded as equivalent when required. 1.3 These practices are intended for the calibration of static force-measuring instruments. It is not applicable for dynamic or high speed force calibrations, nor can the results of calibrations performed in accordance with these practices be assumed valid for dynamic or high speed force measurements. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practices for Calibration and Verification for Force-Measuring Instruments

T/SSM 7-2022 动态汽车衡（非现场用）通用技术条件

本文件规定了动态汽车衡（非现场用）的分类与命名、计量性能要求、通用技术要求、功能要求和检验等内容。 本文件适用于安装于称量控制区，最高运行速度不超过100 km/h，采用重力作用或相关原理获得车辆整车总质量（总重量）的动态汽车衡（非现场用）。

General technical conditions for dynamic truck scales (off-site use)

T/ZZB 2702-2022 敏感类金属波纹管

本文件规定了敏感类金属波纹管（以下简称波纹管）的术语和定义、结构、波纹形状、接口型式、标记、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺。 本文件适用于在仪器仪表领域中使用的敏感类波纹管（铜合金材质：工作温度范围为-60 ℃～100 ℃；不锈钢材质工作温度范围为-196 ℃～+450 ℃）。

Sensitive metal bellows

T/HNJB 7-2021 抗振耐高温发动机油压传感器

本文件规定了抗振耐高温发动机油压传感器（以下简称传感器）的技术要求、试验方法、检验规则、 标志、包装、运输及贮存。 本文件适用于抗振耐高温发动机油压传感器，其它油压传感器也可参照执行。

Anti-Vibration and High Temperature Engine Oil Pressure Sensor

DB31/T 1323-2021 航空航天用压力传感器动态测试方法

Dynamic test method of pressure sensor for aerospace

T/ZZB 2493-2021 电子计重秤

本文件规定了电子计重秤（以下简称“秤”）的术语和定义、基本要求、计量要求、技术要求、试验方法、检验规则、包装、运输、贮存和质量承诺。 本文件适用于由称重传感器为一次转换元件与承载器、电子装置、数字显示装置组成的数字指示式电子计重秤。常用于工业生产、定量包装等过程中计重控制和检验，一般不用于贸易结算。

Electronic weighing scale

KS B 5312-2021 气压计

Barographs

T/ZZB 2249-2021 不断轨无基坑大质量轨道衡

本文件规定了不断轨无基坑大质量轨道衡（以下简称“轨道衡”）的基本要求、计量要求、技术要求、试验与检验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本文件适用于标准轨距、通过动态称量方式确定装载固态或液体物质铁路车辆质量的轨道衡（包括转向架称量和整车称量）。其它轨距、其它量程的自动轨道衡亦可参照使用。

Continuous rail weighbridges of large mass without foundation ditch

DB43/T 2131-2021 动态装载机电子秤通用技术条件

General technical requirements for dynamic loader electronic scales

GSO IEC 62828-2:2021 测试工业和过程测量变送器的参考条件和程序 第2部分：压力变送器的特定程序

IEC 62828-2:2017 establishes specific procedures for testing pressure process measurement transmitters (PMT) used in measuring and control systems for industrial processes and for machinery control systems. A pressure PMT can feature a remote seal to bring the process variable to the sensing element in the PMT. When the remote seal cannot be separated from the PMT, the complete device is tested.

Reference conditions and procedures for testing industrial and process measurement transmitters - Part 2: Specific procedures for pressure transmitters

GSO EN 837-1:2021 压力表 第1部分：波登管压力表 尺寸、计量、要求和测试

This European standard specifies requirements for Bourdon tube (designated by B, see clause 12) indicating pressure gauges, vacuum gauges and combined vacuum and pressure gauges (compound gauges), with circular, spiral or coiled forms, from 40 to 250 nominal size with ranges up to 1600 bar for the measurement of gauge pressure. A reading of zero bar is atmospheric pressure.

Pressure gauges - Part 1: Bourdon tube pressure gauges - Dimensions, metrology, requirements and testing

GSO OIML R106-1:2021 自动轨道衡 第1部分：计量和技术要求 测试

  Scope is not provided for this standard

Automatic rail-weighbridges Part 1: Metrological and technical requirements - Tests

GSO OIML R50-1:2021 连续累加自动衡器（皮带秤） 第1部分：计量技术要求

This International Recommendation specifies the metrological and technical requirements for continuous totalizing automatic weighing instruments of the belt conveyor type, hereinafter referred to as “belt weighers”, that are subject to national metrological control. It is intended to provide standardized requirements and test procedures for evaluating metrological and technical characteristics in a uniform and traceable way.

Continuous totalizing automatic weighing instruments (belt weighers) - Part 1: Metrological and technical requirements

GSO OIML R51-2:2021 自动分选秤 第2部分：测试报告格式

  Scope is not provided for this standard

Automatic catchweighing instruments – Part 2: Test report format

GSO EN 837-2:2021 压力表 第2部分：压力表的选择和安装建议

This part of prEN 837 only applies to those pressure gauges whose pressure responsive element measuring system is a metal part which deforms under the effect of the pressure measured, as defined in prEN 837-1 and EN 837-3. This standard has been prepared to assist in the selection, installation and use of pressure gauges to ensure that they give satisfactory service for the intended application with the maximum level of safety.

Pressure gauges - Part 2: Selection and installation recommendations for pressure gauges

GSO OIML R61-3:2021 自动重量灌装仪器 第3部分：测试报告格式

This “Test Report Format” presents, in a standardized format, the results of the various tests and examinations to which a type of an automatic gravimetric filling instrument (hereafter referred to as “AGFI” shall be submitted with a view to its approval.

Automatic gravimetric filling instruments. Part 3: Test report format