17.100 力、重力和压力的测量 标准查询与下载

T/SSC 2-2024 超导重力仪 通用技术规范

本文件规定了应用于地震领域的超导重力仪技术要求、测试方法和检验规则。

Superconducting gravimeter — General technical specifications

T/QGCML 3384-2024 无人值守地磅收验货系统配置规范

本文件规定了无人值守地磅收验货系统配置规范的术语和定义、要求、硬件配置、软件配置、工程单位配置文档、生产单位配置文档。 本文件适用于无人值守地磅收验货系统的配置管理。

Configuration specifications for unattended weighbridge receipt and inspection system

DB1311/T 040-2023 无转子硫化仪校准规范

本文件规定了无转子硫化仪（以下简称硫化仪）校准的计量特性、条件、项目和方法、结果的表达、复校时间间隔。 本文件适用于衡水市满足GB/T 16584、GB/T 9869、HG/T 3709要求的测定混炼胶胶料硫化特性的橡胶无转子硫化仪的校准。

Rotorless Curing Meter Calibration Specifications

DB1311/T 039-2023 附着力测试仪（拉拔法）校准规范

本文件规定了附着力测试仪（拉拔法）（以下简称附着力测试仪）校准的计量特性、条件、项目和方法、结果的表达、复校时间。 本文件适用于衡水市满足GB/T 1720、GB/T 5210要求的测定漆膜附着力的附着力测试仪的校准。

Calibration specifications for adhesion tester (pull-out method)

T/QGCML 2191-2023 带浮子流量计的气体减压器检测装置

本文件规定了带浮子流量计的气体减压器检测装置的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于带浮子流量计的气体减压器检测装置的生产及检验。

Gas pressure reducer detection device with float flow meter

T/CASME 686-2023 电子厨房秤技术要求

本文件规定了电子厨房秤的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺内容。

Electronic kitchen scale technical requirements

T/CASME 687-2023 电子人体秤技术要求

本文件规定了电子人体秤的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺内容。

Electronic body scales technical requirements

T/CIET 221-2023 智能电子体重秤

本文件规定了智能电子体重秤的术语与定义、功能、产品要求、计量要求、技术要求、检验方法、检验规则、标志、包装、运输和贮存。 本文件适用于智能电子体重秤。

Smart electronic scale

T/XAI 13-2023 覆晶薄膜基板线路剥离强度测试方法

1　范围、2　规范性引用文件、3　术语和定义、4　测试原理、5　测试装置、6　样品制备、7　测试方法、8　测试报告。

The test method for Peeling of COF

T/QGCML 1103-2023 电子台秤

本文件规定了电子台秤的术语和定义、型号、计量要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于由称重传感器为一次转换元件与承载器、电子装置、数字显示装置组成的数字指示式电子台秤（以下简称“秤”）。

Electronic scale

T/QGCML 1102-2023 电子计价秤

本文件规定了电子计价秤的术语和定义、型号、计量要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于由称重传感器为一次转换元件与承载器、电子装置、数字显示装置组成的，具有计价功能的数字指示式电子计价秤（以下简称“秤”）。

Electronic pricing scale

T/CASME 477-2023 瓶装在线动态检测机

本文件规定了瓶装在线动态检测机的型号及组成、总体要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

Bottle online dynamic inspection machine

T/QGCML 710-2023 汽车衡生产技术规范

本标准规定了汽车衡生产技术规范的术语定义、代号及命名、基本要求、生产流程、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于电子汽车衡SCS-10～150t系列衡器的设计、生产。

Technical specifications for the production of truck scales

ASTM F3109-23 多轴测力平台验证的标准实施规程

1.1 This standard recommends practices for performance verification of multi-axis force platforms commonly used for measuring ground reaction forces during gait, balance, and other activities. 1.1.1 This standard provides a method to quantify the relationship between applied input force and force platform output signals across the manufacturer’s defined spatial working surface and specified force operating range. 1.1.2 This standard provides definitions of the critical parameters necessary to quantify the behavior of multi-axis force measuring platforms and the methods to measure the parameters. 1.1.3 This standard presents methods for the quantification of spatially distributed errors and absolute measuring performance of the force platform at discrete spatial intervals and discrete force levels on the working surface of the platform. 1.1.4 This standard further defines certain important derived parameters, notably COP (center of pressure) and methods to quantify and report the measuring performance of such derived parameters at spatial intervals and force levels across the working range of the force platform. 1.1.5 This standard defines the requirements for a report suitable to characterize the force platform’s performance and provide traceable documentation to be distributed by the manufacturer or calibration facility to the users of such platforms. 1.1.6 Dynamic characteristics and applications where the force platform is incorporated in other equipment, such as instrumented treadmills and stairs, are beyond the scope of this standard. 1.1.7 This standard is written for purposes of multi-axis force platform verification. However, the methods and procedures are applicable to calibration of force platforms by manufacturers. 1.2 The values stated in SI units are to be regarded as the standard. Other metric and inch-pound values are regarded as equivalent when required. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Verification of Multi-Axis Force Measuring Platforms

T/CWIAS 0001.2-2023 集装箱超偏载检测仪 第2部分:悬吊式

本文件规定了悬吊式集装箱超偏载检测仪（以下简称检测仪）的术语和定义、型号及规格的命名、计量要求、技术要求、试验方法、检验规则和标志、包装、运输、贮存等。 本文件适用于通过安装于集装箱吊具上或集装箱专用起重机相关部位的称重传感器，并与数字指示装置连接，实现对集装箱的总重和重心位置进行测量的装置。

Detecting Instrument for Overload And Unbalanced Load of Freight Container Part 2：Suspension Type

T/HBMIF 005-2022 地面强度检测仪技术要求

本文件规定了地面强度检测仪的术语和定义、产品构成及基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于检测地面强度不小于0.6MPa的地面强度检测仪的生产、检验。

Technical requirements for ground strength detector

T/ZZB 2860-2022 焊接、切割及类似工艺用气瓶减压器

本文件规定了焊接、切割及类似工艺用气瓶减压器（以下简称减压器）的术语和定义、单位及符号、基本要求、技术要求、试验方法、检验规则、标志、使用说明书、包装、运输与贮存及质量承诺。 本文件适用于在焊接、切割及类似工艺过程中，压力在30 MPa以内的压缩气体、溶解乙炔、液化石油气（LPG）、甲基乙炔—丙二烯混合物（MPS）和二氧化碳（CO2）等单级气瓶减压器。

Regulators for welding,cutting and the similar processes

T/ZZB 2971-2022 叉簧式抗震压力表

本文件规定了叉簧式抗震压力表的术语和定义、分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本文件适用于以叉簧为测量元件，表壳内有灌充液并带有阻尼装置的抗震压力表（以下简称“仪表”）。

Shock-resistant pressure gauge with fork spring

T/CASME 54-2022 硅压阻式充油型压力传感器

本文件规定了硅压阻式充油型压力传感器的分类和命名、结构、基本参数、要求、试验方法、检验规则、标志、包装、运输和贮存。

Silicon piezoresistive oil-filled pressure sensor

ASTM F721-18(2022) 仪表管道组件标准规范

1.1 This specification covers details of gauge piping assemblies for pressure gauges with optional provisions for additional gauges, pressure switches, transmitters, and so forth, for use with steam, steam drains, feed water, condensate, fresh water, salt water, compressed air, fuel oil, and lubricating oil systems. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Gauge Piping Assemblies