17.200.10 热、量热学 标准查询与下载

ASTM E1354-22 用耗氧量热计测定材料和产品的热和可见烟雾释放率的标准试验方法

Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter

ASTM E1461-13(2022) 闪光法测定热扩散率的标准试验方法

1.1 This test method covers the determination of the thermal diffusivity of primarily homogeneous isotropic solid materials. Thermal diffusivity values ranging from 0.1 to 1000 (mm)2 s-1 are measurable by this test method from about 75 to 2800 K. 1.2 Practice E2585 is adjunct to this test method and contains detailed information regarding the use of the flash method. The two documents are complementing each other. 1.3 This test method is a more detailed form of Test Method C714, having applicability to much wider ranges of materials, applications, and temperatures, with improved accuracy of measurements. 1.4 This test method is intended to allow a wide variety of apparatus designs. It is not practical in a test method of this type to establish details of construction and procedures to cover all contingencies that might offer difficulties to a person without pertinent technical knowledge, or to restrict research and development for improvements in the basic technique. 1.5 This test method is applicable to the measurements performed on essentially fully dense (preferably, but low porosity would be acceptable), homogeneous, and isotropic solid materials that are opaque to the applied energy pulse. Experience shows that some deviation from these strict guidelines can be accommodated with care and proper experimental design, substantially broadening the usefulness of the method. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 For systems employing lasers as power sources, it is imperative that the safety requirement be fully met. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Thermal Diffusivity by the Flash Method

ASTM E422-22 用水冷式热量计测量净热通量的标准试验方法

1.1 This test method covers the measurement of a steady net heat flux to a given water-cooled surface by means of a system energy balance. 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Net Heat Flux Using a Water-Cooled Calorimeter

ASTM D6011-96(2022) 测定声速风速计/温度计性能的标准试验方法

1.1 This test method covers the determination of the dynamic performance of a sonic anemometer/thermometer which employs the inverse time measurement technique for velocity or speed of sound, or both. Performance criteria include: (a) acceptance angle, (b) acoustic pathlength, (c) system delay, (d) system delay mismatch, (e) thermal stability range, (f) shadow correction, (g) velocity calibration range, and (h) velocity resolution. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Performance of a Sonic Anemometer/Thermometer

ASTM E2602-22 用调制温度差示扫描量热法测定玻璃化转变温度的标准试验方法

1.1 These test methods describe the assignment of the glass transition temperature of materials using modulated temperature differential scanning calorimetry (MTDSC) over the temperature range from –120 °C to +600 °C. The temperature range may be extended depending upon the instrumentation used. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Assignment of the Glass Transition Temperature by Modulated Temperature Differential Scanning Calorimetry

ASTM C1171-16(2022) 定量测量耐火材料热冲击和热循环影响的标准试验方法

1.1 This test method is used for determining the strength loss or reduction in continuity, or both, of prism-shaped specimens which are cut from refractory brick or shapes and subjected to thermal cycling. 1.2 The strength loss is measured by the difference in modulus of rupture (MOR) between uncycled specimens and the specimens subjected to thermal cycling. 1.3 The reduction in structural continuity is estimated by the difference in sonic velocity before and after thermal cycling. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Quantitatively Measuring the Effect of Thermal Shock and Thermal Cycling on Refractories

T/GDCKCJH 050-2021 二氧化碳培养箱性能要求与检测方法

本文件规定了二氧化碳培养箱的术语和定义、性能要求及检测方法。

Performance requirements and test method for carbon dioxide incubator

ASTM E2890-21 用Kissinger法和Farjas法用差示扫描量热法测定热不稳定材料的动力学参数和反应级数的标准试验方法

1.1 This test method describes the determination of the kinetic parameters of Arrhenius activation energy and preexponential factor using the Kissinger variable heating rate iso-conversion method (1, 2)2 and activation energy and reaction order by the Farjas method (3) for thermally unstable materials. The test method is applicable to the temperature range from 300 K to 900 K (27 °C to 627 °C). 1.2 Both nth order and accelerating reactions are addressed by this method over the range of 0.5 < n < 4 and 1 < p < 4 where n is the nth order reaction order and p is the Avrami reaction order (4). Reaction orders n and p are determined by the Farjas method (3). 1.3 This test method uses the same experimental conditions as Test Method E698. The Flynn/Wall/Ozawa data treatment of Test Method E698 may be simultaneously applied to these experimental results. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Kinetic Parameters and Reaction Order for Thermally Unstable Materials by Differential Scanning Calorimetry Using the Kissinger and Farjas Methods

DIN 51007-2:2021 热分析 差热分析（DTA）和差示扫描量热法（DSC） 第2部分：快速差示扫描量热法（f-DSC）；芯片量热法

This document establishes principles for non-adiabatic fast differential scanning calorimetry (f-DSC) applications with open sample geometry on solids and liquids.

Thermal analysis - Differential thermal analysis (DTA) and Differential scanning calorimetry (DSC) - Part 2: Fast differential scanning calorimetry (f-DSC); Chip calorimetry

ASTM E2253-21 差示扫描量热仪的温度和焓测量验证的标准试验方法

1.1?This test method provides procedures for validating temperature and enthalpy measurements of differential scanning calorimeters (DSC) and analytical methods based upon the measurement of temperature or enthalpy (or heat), or both, by DSC. Performance parameters determined in

Standard Test Method for Temperature and Enthalpy Measurement Validation of Differential Scanning Calorimeters

ASTM E3174-21 用差示扫描量热法测定动力学反应模型的标准实施规程

Standard Practice for Determination of Kinetic Reaction Model Using Differential Scanning Calorimetry

ASTM D7314-21 使用量热法和在线/在线采样测定气态燃料的热值的标准实践

1.1?This practice is for the determination of the heating value measurement of gaseous fuels using a calorimeter. Heating value determination of sample gasses containing water vapor will require vapor phase moisture measurements of the pre-combustion sample gas as well as the no

Standard Practice for Determination of the Heating Value of Gaseous Fuels using Calorimetry and On-line/At-line Sampling

BS PD CEN/TR 13582:2021 热能表的安装 热能表的选择、安装和操作指南

Installation of thermal energy meters. Guidelines for the selection, installation and operation of thermal energy meters

DS/CEN/TR 13582:2021 热能表的安装《热能表选用、安装和使用指南》

Installation of thermal energy meters – Guidelines for the selection, installation and operation of thermal energy meters

PD CEN/TR 13582:2021 热能表的安装 热能表的选择、安装和操作指南

Installation of thermal energy meters - Guidelines for the selection, installation and operation of thermal energy meters

ASTM C1130-21 校准薄型热通量传感器的标准实践

1.1?This practice, in conjunction with either Test Method C177, C518, C1114, or C1363, establishes procedures for the calibration of heat flux transducers that are dimensionally thin in comparison to their planar dimensions. 1.1.1 The thickness of the heat flux transducer shall

Standard Practice for Calibrating Thin Heat Flux Transducers

KS B 50075-2-2020 热量表 第2部分:型式认可试验

Heat meters — Part 2: Type approval tests

KS A 5001-2020 热平衡图符号

Symbol of heat balance diagram

BS EN 1434-5:2015+A1:2019 热能表 初始验证测试

Thermal energy meters. Initial verification tests

DIN SPEC 91420:2020 立方参考建筑气候相关热边界条件的热辐射和热量测量的动态室内测量方法

This DIN SPEC defines standards for the calorimetric measurement of the weather related thermal effects upon a building and the dynamic measurement of heat radiation inside the building.

Dynamic in-door measuring method for thermal radiation and calorimetric measurements of climate related thermal boundary conditions of a cubic reference building