共找到 150 条与 电学、磁学综合 相关的标准,共 10 页
Testing method of resistivity for silicon crystals and silicon wafers with four - point probe
Standard Test Method for Measuring Relative Complex Permittivity and Relative Magnetic Permeability of Solid Materials at Microwave Frequencies Using Waveguide
1.1 This guide covers the application of routine calculations to estimate sample system lag time, in seconds, for gas, liquid, and mixed phase systems. 1.2 This guide considers the sources of lag time from the process sample tap, tap conditioning, sample transport, preanalysis conditioning and analysis. 1.3 Lag times are estimated based on a prediction of flow characteristics, turbulent, non turbulent, or laminar, and the corresponding purge requirements. 1.4 Mixed phase systems prevent reliable representative sampling so system lag times should not be used to predict sample representation of a mixed phase stream. 1.5 The values stated in inch-pound units are to be regarded as standard. Other units of measurement are included in this standard and Appendix X1 examples where normally seen in industry. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Guide for Prediction of Analyzer Sample System Lag Times
本标准规定了永磁体表面磁场的术语及定义、测试原理、测试装置、试样与测试夹具、测试、测量、结果处理以及测试报告。
Test method for surface magnetic field of permanent magnet
Guidance for evaluation of products with respect to substance-use restrictions in electrical and electronic products
Magnetic materials – Part 11: Methods of measurement of the surface insulation resistance of electrical steel strip and sheet
Magnetic materials. Methods of measurement of the surface insulation resistance of electrical steel strip and sheet
Electricity metering data exchange — The DLMS / COSEM suite Part 3 - 1 : Use of local area networks on twisted pair with carrier signalling
Short-circuit currents in three-phase AC systems – Part 4: Examples for the calculation of short-circuit currents
本文件适用于探测 100-1000V 间的单极对地交、直流电压的电压测试器。
Voltage Tester
Superconductivity. Electronic characteristic measurements. Local critical current density and its distribution in large-area superconducting films
This part of IEC 62056 specifies the overall structure of the OBject Identification System (OBIS) and the mapping of all commonly used data items in metering equipment to their identification codes.
Electricity metering data exchange - The DLMS/COSEM suite - Part 6-1: Object Identification System (OBIS) (IEC 62056-6-1:2017); English version EN 62056-6-1:2017
Amendment 5 - International Electrotechnical Vocabulary (IEV) - Part 121: Electromagnetism
Short-circuit currents in d.c. auxiliary installations in power plants and substations ― Part 2: Calculation of effects
Short-circuit currents in d.c. auxiliary installations in power plants and substations — Part 1: Calculation of short-circuit currents
Amendment 3 - International Electrotechnical Vocabulary (IEV) - Part 121: Electromagnetism
Test method for volume resistivity of conductive powder for electromagnetic shielding
1.1 This test method covers the generation of electrostatic charge, the measurement of this charge and its associated electric field, and the test conditions which must be controlled in order to obtain reproducible results. This test method is applicable to both solids and liquids. This test method is not applicable to gases, since a transfer of a gas with no solid impurities in it does not generate an electrostatic charge. This test method also does not cover the beneficial uses of static electrification, its associated problems or hazards, or the elimination or reduction of unwanted electrostatic charge.2 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Static Electrification
本标准规定了基于法拉第电磁感应原理的永磁体磁偏角线圈法测量方法
Measurement method for the deflected angle of magnetization of permanent magnet use Helmholtz coils
Substance and material declaration standard
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号