共找到 150 条与 电学、磁学综合 相关的标准,共 10 页
Magnetic materials - Part 11: Method of test for the determination of surface insulation resistance of magnetic sheet and strip
Short-circuit current - Calculation of effects - Part 2: Examples of calculation
Calibration of electromagnetic field sensors and probes, excluding antennas, from 9 kHz to 40 GHz; Corrections
This test method covers the generation of electrostatic charge, the measurement of this charge and its associated electric field, and the test conditions which must be controlled in order to obtain reproducible results. This test method is applicable to both solids and liquids. This test method is not applicable to gases, since a transfer of a gas with no solid impurities in it does not generate an electrostatic charge. This test method also does not cover the beneficial uses of static electrification, its associated problems or hazards, or the elimination or reduction of unwanted electrostatic charge. The values stated in SI units are to be regarded as the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Test Method for Static Electrification (10.02)
Calibration of electromagnetic field sensors and probes, excluding antennas, from 9 kHz to 40 GHz
This standard is Short-circuit currents; calculation of effects; part 1: definitions and calculation methods; Corrigendum 1.
Short-circuit currents; calculation of effects; part 1: definitions and calculation methods
The object is to show the application of procedures for the calculation of mechanical and thermal effects due to short circuits as presented in IEC 865-1. Thus, it is in addition to IEC 865-1. However, it does not change the basis for standardized proced
Short-circuit currents - Calculation of effects - Part 2: Examples of calculation
Short-circuit currents. Calculation of effects. Part 1 : definitions and calculation methods.
Quantities used in alternating current theory; two-line circuits
Applies to a.c. systems having rated voltages up to and including 420 kV.
Short-circuit currents - Calculation of effects - Definitions and calculation methods
Is applicable to the mechanical and thermal effects of short-circuit currents. Contains standardized procedures for the calculation of the effects of the short-circuit currents in two sections: the electromagnetic effect on rigid conductors and flexible
Short-circuit currents; calculation of effects; part 1: definitions and calculation methods
Comprises data collected from different countries to be used when necessary for calculating short-circuit currents in accordance with IEC 781 and IEC 909. In general data are presented in the form of curve sheets. For each type of equipment (synchronous
Electrical equipment; data for short-circuit current calculations in accordance with IEC 60909:1988
Electrostatic discharge (ESD); characterization of the ESD environment / Note: Approved 1997-00-00.
Guide on Electrostatic Discharge (ESD): Characterization of the ESD Environment R(1997)
Short-circuit current calculation in three-phase a.c. systems; part 1: factors for the calculation of short-circuit currents in three-phase a.c. systems according to IEC 909
This standard deals with the physical principles for electromagnetic waves, their mathematical presentation and related concepts.#,,#
Electromagnetic field; electromagnetic waves
This standard explains the state quantities of the electromagnetic field in a comprehensive form. It is related to chapter 121 of the international electrotechnical vocabulary (IEV).
Electromagnetic field; state quantities
This standard explains the material quantities which describe the relationship established by the material between the field quantities of the electromagnetic field. It is related to chapter 121 of the international electrotechnical vacubulary (IEV).
Electromagnetic field; material quantities
Short-circuit current calculation in three-phase a.c. systems
Настоящий стандарт распространяется на государственный специальный эталон и государственную поверочную схему для средств измерений угл
State system for ensuring the uniformity of measurements. State special standard and state verification schedule for means measuring phase shift angle with in the frequency range from 25,95 to 37,50 GHz
Considerations on reference impedances for use in determining the disturbance characteristics of household appliances and similar electrical equipment
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号