17.240 辐射测量 标准查询与下载

GB/T 10263.4-1988 辐射探测器环境试验基本要求与方法 磁场试验

本标准规定了磁场试验的规范、要求与方法。 本标准适用于辐射探测器的磁场试验。也适用于光电倍增管。

Basic enviromental testing procedures for radiation detectors--Tests for effect of magnetic field

GB/T 10263.7-1988 辐射探测器环境试验基本要求与方法 盐雾试验

本标准规定了盐雾试验的规范、要求与方法。 本标准适用于辐射探测器在非包装情况下产品的盐雾试验。

Basic enviromental testing procedures for radiation detectors--Test for effect of salt mist

GB/T 10263.10-1988 辐射探测器环境试验基本要求与方法 包装运输试验

本标准规定了运输试验的规范、要求与方法。 本标准适用于辐射探测器在完整包装状态下的运输试验。也适用于组成辐射探测器的部件，如光电倍增管和闪烁体。

Basic enviromental testing procedures for radiation detectors--Transportation test

GB/T 10263.2-1988 辐射探测器环境试验基本要求与方法 温度试验

本标准规定了温度试验的规范、要求与方法。 本标准适用于辐射探测器的温度试验。 也适用于组成辐射探测器的部件。 例如光电倍增管和闪烁体。

Basic enviromental testing procedures for radiation detectors--Temperature test

GB/T 10263.8-1988 辐射探测器环境试验基本要求与方法 振动试验

本标准规定了振动试验的规范、要求与方法。 本标准适用于辐射探测器在非包装状态下的振动试验。也适用于组成辐射探测器的部件，如光电倍增管和闪烁体。

Basic enviromental testing procedures for radiation detectors--Vibration test

GB/T 10263.5-1988 辐射探测器环境试验基本要求与方法 光效应试验

本标准规定了光效应试验的规范、要求与方法。 本标准适用于辐射探测器的光效应试验。也适用于光电倍增管。

Basic enviromental testing procedures for radiation detectors--Effective testing of exposure to light

GB/T 10263.6-1988 辐射探测器环境试验基本要求和方法 辐照试验

本标准规定了辐照试验的规范、要求与方法。 本标准适用于辐射探测器的辐照试验。也适用于组成辐射探测器的部件，如光电倍增管和闪烁体。

Basic enviromental testing procedures for radiation detectors--Irradiation test

GB/T 7165.5-1988 气态排出流(放射性)活度连续监测设备 第5部分:氚排出流监测仪的特殊要求

本标准规定了气态氚监测仪的特殊要求，其中包括设计要求，技术特性和检验方法等，并给出检验方法之实例。 本标准必须与GB7165.1结合使用，除非另有说明，第一部分规定的一般要求都适用于本标准。 本标准适用于核设施在正常运行（包括预期运行事件）条件下，向环境排出的气态排出流中氚放射性活度的连续监测设备。

Equipment for continuously monitoring radioactivity in gaseous effluents--Part 5:Specific requirements for tritium effluent monitors

GB/T 10264-1988 个人和环境监测用热释光剂量测量系统

本标准规定了个人和环境监测用热释光辐射剂量测量系统、探测器及读出器的分类与符号、性能标准和相应的检验规则，但不包括信息存取及数据处理部分。

Thermoluminescence dosimetry for personal and environmental monitoring

GB/T 7165.2-1988 气态排出流(放射性)活度连续监测设备 第2部分:气溶胶排出流监测仪的特殊要求

本标准是《气态排出流（放射性）活度连续监测设备》的第二部分气溶胶排出流监测仪的特殊要求。 本标准必须与《气态排出流（放射性）活度连续监测设备》的第一部分结合使用。除非另有说明，第一部分规定的一般要求都适用于本标准。 本标准是为气溶胶排出流监测仪规定的特殊要求，其中包括设计要求、技术特性和检验方法等，并给出检验方法之实例。 本标准适用于核设施正常运行（包括预期运行事件）条件下向环境排放的气态排出流中气溶胶活度的连续监测设备，这类设备应具有下述功能： a.测量气态排出流中气溶胶的放射性浓度及其随时间的变化，或者在一段较长的时间（如24h）内的气溶胶累积活度。 b.当气溶胶放射性浓度或者累积活度超过预定值时，给出报警信号。

Equipment for continuously monitoring radioactivity in gaseous effluents--Part 2: specific requirements for aerosol effluent monitors

GB/T 7166-1987 核动力堆堆芯或堆主包壳内温度测量 特性和测试方法

本标准是核动力堆堆芯或堆主包壳内温度测量装置的特性、设计、制造和测试方法的通用规定，重点在于堆主包壳内或强辐射区中应用的特性上。

In-core temperature or primary envelope temperature measurements in nuclear power reactor--Characteristics and test methods

GB/T 7165.1-1987 气态排出流(放射性)活度连续监测设备 第1部分:一般要求

本标准适用于核设施在正常运行和预期运行事件时使用的排出流活度连续监测设备，但这种设备在事故发生时也可能工作。对于专门为事故监测用的气态排出流活度连续监测设备则需满足其他特性要求。 本标准不包括作为气态排出流监测计划基本组成部分的取样和实验室分析方面的技术要求。

Equipment for continuously monitoring radioactivity in gaseous effluents--Part 1: General requirements

GB/T 5964-1986 核仪器用高压同轴连接器

本标准适用于与核电子仪器相连接的高压同轴连接器，规定了两种型式的高压同轴连接器结构和配合部分的尺寸及主要电性能。 按本标准规定的结构和尺寸及技术要求制造的产品与国外同类产品在机械和电性能上可达到完全互换。

High voltage coaxial connectors used in nuclear instrumentation

GB 5202-1985 α、β 和α-β表面污染测量仪与监测仪

Alpha,beta and alpha-beta surface contamination meters and monitors

GB/T 5202-1985 α、β和α-β表面污染测量仪与监测仪

本标准适用于测量或探测表面污染辐射α、β和α-β粒子的测量仪与监测仪。这类装置至少包括探测器和测量部件两部分。

Alpha,beta and alpha-beta surface contamination meters and monitors

GB/T 4861-1984 模拟计数率表特性和测试方法

本文的规定适用于普通测量范围（0.1脉冲/秒～106脉冲/秒）内的线性和对数模拟计数率表。 率表可以是单独的或为其他仪器的一部分。 本文不对定型、例行和交收等测试类别进行区分，也不对指定特性给出具体数值，执行中应根据仪器的具体用途加以必要的说明。 本文规定了表示计数率表工作性能的最常用的特性，并建立一套验证这些特性的相应的测试方法。

Analogue counting ratemeters characteristics and test methods

GB/T 4835-1984 辐射防护用携带式X、γ辐射剂量率仪和监测仪

本标准适用于辐射防护领域中携带式X、γ辐射剂量率仪和监测仪，测量的能量范围为50keV到3MeV。这种装置至少包括探测部件和测量部件。这两部分可以直接连接，可以通过软电缆连接，也可以组成一台装置。

Portable X or gamma radiation doserate meters and monitors for use in radiation protection

GB/T 4080-1983 用于放射性测量的试管尺寸

本标准适用于放射性测量用的试管和管塞。

Dimensions of test tubes for radioactivity measurements

ASTM ISO/ASTM 51707-22 辐射处理剂量测量不确定度评估的标准指南

1.1  This standard provides guidance on the use of concepts described in the JCGM (Joint Committee for Guides in Metrology ) Evaluation of Measurement Data – Guide to the Expression of Uncertainty in Measurement (GUM) to estimate the uncertainties in the measurement of absorbed dose in radiation processing. 1.2  Methods are given for identifying, evaluating, and estimating the components of measurement uncertainty associated with the use of dosimetry systems, and for calculating combined standard measurement uncertainty and expanded uncertainty of dose measurements based on the GUM methodology. 1.3  Examples are given on how to develop a measurement uncertainty budget and a statement of uncertainty. 1.3.1  Key components of uncertainty are derived as part of the derivation of the uncertainty budget. This standard identifies which components of uncertainty are carried forward as part of other analyses (e.g., assessment of process capability and process targets, and process variability), and which components from other standards are brought forward into this standard (e.g., precision of the dose measurement, calibration curve fit, and indirect measurement of dose). 1.4  This document is one of a set of standards that provides recommendations for properly implementing dosimetry in radiation processing, and provides guidance for achieving compliance with the requirements of ISO 11137-1 (radiation sterilization of health care products), ISO 14470 (treatment of food), and ISO/ASTM 52628 related to the evaluation and documentation of the uncertainties associated with measurements made with a dosimetry system. It is intended to be read in conjunction with ISO/ASTM 52628 (Standard Practice for Dosimetry in Radiation Processing), and ISO/ASTM 51261 (Practice for Calibration of Routine Dosimetry Systems for Radiation Processing). 1.5  To achieve compliance with the requirements of ISO 11137-1 (radiation sterilization of health care products), ISO 14470 (treatment of food), and other applications, a measurement is accompanied by a statement of the uncertainty. 1.6  This guide does not address the establishment of process specifications or conformity assessment. 1.7  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Estimation of Measurement Uncertainty in Dosimetry for Radiation Processing

ASTM ISO/ASTM 51649-22 能量为 300keV 至 25MeV 的电子束辐射处理的标准规范

1.1  This practice outlines dosimetric procedures to be followed in installation qualification (IQ), operational qualification (OQ) and performance qualifications (PQ), and routine processing at electron beam facilities. 1.2  The electron beam energy range covered in this practice is between 300 keV and 25 MeV, although there are some discussions for other energies. 1.3  Dosimetry is only one component of a total quality assurance program for adherence to good manufacturing practices used in radiation processing applications. Other measures besides dosimetry may be required for specific applications such as health care product sterilization and food preservation. 1.4  Specific standards exist for the radiation sterilization of health care products and the irradiation of food. For the radiation sterilization of health care products, see ISO 11137-1 (Requirements) and ISO 11137-3 (Guidance on dosimetric aspects). For irradiation of food, see ISO 14470. In those areas covered by these standards, they take precedence. Information about effective or regulatory dose limits for food products is not within the scope of this practice (see ASTM Guides F1355 , F1356 , F1736 , and F1885 ). 1.5  This document is one of a set of standards that provides recommendations for properly implementing and utilizing dosimetry in radiation processing. It is intended to be read in conjunction with ISO/ASTM 52628 , “Practice for Dosimetry in Radiation Processing”. Note 1:  For guidance in the calibration of routine dosimetry systems, see ISO/ASTM Practice 51261 . For further guidance in the use of specific dosimetry systems, see relevant ISO/ASTM Practices. For discussion of radiation dosimetry for pulsed radiation, see ICRU Report 34. 1.6  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Electron Beam Radiation Processing at Energies Between 300 keV and 25 MeV