21.260 润滑系统 标准查询与下载
共找到 217 条与 润滑系统 相关的标准，共 15 页
Continuous casting machine dry oil centralized gas station
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
Technical conditions of thin oil lubrication device
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
Double-column lifting electric grease pump (20MPa)
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
Screw pump for lubrication device
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
Grease-free electric lubrication pump (20MPa)
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
Lubrication system electromagnetic stop valve (31.5MPa)
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
Single line distributor (31.5MPa)
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
Grease Lubrication Pump Part 1: Electric Lubrication Pump (40MPa)
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
Grease lubrication pump part 3: multi-point lubrication pump (31.5MPa)
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
Dry oil lubrication device for continuous casting machine
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
Thin oil lubrication device for dynamic and static pressure bearings
- ICS
- 21.260
- CCS
- J21
- 发布
- 2016-01-15
- 实施
- 2016-06-01
5.1 Fretting wear and corrosion are potential serviceability factors in many machines. They have always been factors in shipping finished goods by truck or rail. Packing materials rubbing on a product in transit can make the product unsalable. Beverage cans and food cans can lose their trade dress and consumers often equate container damage to content damage. 5.2 Clamping surfaces on injection molds are damaged by fretting motions on clamping. This damage is a significant cause for mold replacement. 5.3 Machines in shipment are subject to fretting damage in the real area of contact of the bearings on the machines. 5.4 Operating vibration and movement of mechanically clamped components, like screwed assemblies, can produce damage on the clamped faces and other faces that affects machine function or use. Many times fretting damage appears in the form of pits, which are stress concentrators that can lead to mechanical fractures. 5.5 Electrical contacts in any device that is subject to vibration are susceptible to failure (open circuit) due to fretting damage at real areas of contact. 5.6 This test method is intended to be used to identify mating couples that may be less prone to fretting damage than others. This information in turn is used to select materials of construction or surface treatments that are less prone to fretting damage for applications where fretting conditions are known or perceived to exist. 1.1 This test method covers the studying or ranking the susceptibility of candidate materials to fretting corrosion or fretting wear for the purposes of material selection for applications where fretting corrosion or fretting wear can limit serviceability. 1.2 This test method uses a tribological bench test apparatus with a mechanism or device that will produce the necessary relative motion between a contacting hemispherical rider and a flat counterface. The rider is pressed against the flat counterface with a loading mass. The test method is intended for use in room temperature air, but future editions could include fretting in the presence of lubricants or other environments. 1.3 The purpose of this test method is to rub two solid surfaces together under controlled fretting conditions and to quantify the damage to both surfaces in units of volume loss for the test method. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Damage to Contacting Solid Surfaces under Fretting Conditions
- ICS
- 21.260
- CCS
- 发布
- 2015
- 实施
1.1 This specification covers material, design, structural performance, and manufacturing practice requirements for monolithic or sectional corrugated polyethylene grease interceptor tanks with volumes equal to or greater than 333 gallons (1,260 liters ). 1.2 The corrugated high density polyethylene (HDPE) grease interceptor tanks are placed between commercial food service (kitchen) drains and sanitary sewer interceptors to minimize the impact of commercial food service effluent containing grease, oils, soap scum and other typical commercial food service wastes on the sanitary sewer system. Typical sources of commercial kitchen effluent are scullery sinks, pot and pan sinks, dishwashers, soup kettles and floor drains where grease containing materials may exist. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This specification covers pipe and fittings for horizontally laid corrugated HDPE grease interceptor tanks as illustrated in Fig. 1. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Corrugated High Density Polyethylene (HDPE) Grease Interceptor Tanks
- ICS
- 21.260
- CCS
- 发布
- 2014-12-25
- 实施
本标准规定了稀油润滑装置的基本参数、系统原理、主要元件与部件、控制要求、型式、尺寸与标记。本标准适用于机械设备稀油循环润滑系统的稀油润滑装置(以下简称装置)。
The oil lubrication equipment.The type, basic parameter and size
- ICS
- 21.260
- CCS
- J21
- 发布
- 2014-07-09
- 实施
- 2014-11-01
MQL processing technology - Part 4: Tapping chuck and tab/cold forming tab
- ICS
- 21.260
- CCS
- J21
- 发布
- 2014-03
- 实施
