21.260 润滑系统 标准查询与下载

JB/T 8810.2-1998 单线润滑泵31.5MPa

JB/T 8801.2-1998 本标准规定了单线润滑泵 31.5MPa 的型号，基本参数与外形尺寸，技术要求，试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于向集中润滑脂、油，公称压力为 31.5MPa的单线润滑泵。 （注： 本标准自实施之日起，JB/ZQ 4580-86《单线润滑泵（20MPa）》作废。）

Single-line lubrication pumps 31.5 MPa

BS ISO 6301-2:1998 气动流体动力 压缩空气润滑器 供货商文件包括主要特性测定的试验方法

Pneumatic fluid power. Compressed air lubricators. Test methods to determine the main characteristics to be included in supplier's literature

BS 7403-1:1998 用于内燃机的全流式润滑油过滤器 压差/流量特性的测试方法

This part of ISO 4548 specifies tests for determining the differential pressure/flow characteristics of full-flow lubricating oil filters for internal combustion engines. Tests are specified with oils at two viscosities, one to assess the performance of a filter with a cold oil and the other to assess its performance with an oil at a typical operating temperature.

Full-flow lubricating oil filters for internal combustion engines. Methods of test for differential pressure/flow characteristics

BS 7403-2:1998 用于内燃机的全流式润滑油过滤器 元件旁通阀特性的试验方法

This part of ISO 4548 specifies tests for determining the element by-pass valve characteristics of full-flow lubricating oil filters for internal combustion engines. Tests are specified with oils at two viscosities, one to assess the performance of an element by-pass valve with a cold oil and the other to assess its performance with an oil at a typical operating temperature.

Full-flow lubricating oil filters for internal combustion engines. Method of test for element by-pass valve characteristics

BS 7403-4:1998 用于内燃机的全流式润滑油过滤器 初始颗粒截留效率、寿命和累积效率的测试方法（重量法）

This part of ISO 4548 specifies tests for determining the performance of full-flow lubricating oil filters for internal combustion engines as follows. Section 2: Initial particle retention efficiency. This gives the test procedures and parameters for the determination of the initial particle retention efficiency of lubricating oil filter elements under defined test conditions. By reporting the results in accordance with subclause 2.6, the probable retention efficiency for any particle size may be derived. The retention efficiency is determined by the gravimetric method. Section 3: Life and cumulative efficiency. This gives the test procedures and parameters for the determination of element life and cumulative efficiency of lubricating oil filters. The cumulative efficiency is determined by the gravimetric method. NOTE —By agreement between filter manufacturer and purchaser, tests on large filters can be conducted on the basis of tests carried out on filters scaled-down in length. The relationship of the filter flow and test dust addition rate to the effective length of the filter medium should be the same in the scaled-down tests as in the full size filter. For the purposes of this part of ISO 4548, a filter having a test flow rate exceeding 100 l/min is considered large.

Full-flow lubricating oil filters for internal combustion engines. Methods of test for initial particle retention efficiency, life and cumulative efficiency (gravimetric method)

BS 7403-3:1998 用于内燃机的全流式润滑油过滤器 耐高压差和耐高温试验方法

This part of ISO 4548 specifies tests for measuring the resistance to high differential pressure and the resistance to elevated temperatures of filter elements of full-flow lubricating oil filters for internal combustion engines.

Full-flow lubricating oil filters for internal combustion engines. Methods of test for resistance to high differential pressure and to elevated temperature

BS 7403-11:1998 用于内燃机的全流式润滑油过滤器 自清洁过滤器的测试方法

This part of ISO 4548 specifies test methods for evaluating the characteristics of self-cleaning oil filters for internal combustion engines. It is applicable to filters in which self-cleaning is continuous or intermittent. The removal of retained particles from the filter is achieved by periodic reversal of the direction of the fluid flow through the elements. However, this also applies mechanical stresses to the filter media. The tests specified in this standard are designed to check the filtration performance of the elements under simulated operating conditions and to confirm their ability to withstand, without damage, variations in oil pressure, temperature, direction of flow and the presence of water. The equipment and procedures specified in this part of ISO 4548 are recommended for filters having a nominal flow rate of up to 1 600 l/min.

Full-flow lubricating oil filters for internal combustion engines. Methods of test for self-cleaning filters

ISO 6301-1:1997 气压传动 压缩空气油雾器 第1部分:供应商文件和产品标志要求中应包含的主要特性

This part of ISO 6301 specifies which characteristics of compressed air lubricators are to be included in the supplier's literature. It also specifies product-marking requirements which the lubricators must meet. This part of ISO 6301 applies to compressed air lubricators, constructed from light alloys (aluminium, etc), zinc diecast alloys, brass, steel and plastic, with a rated pressure of 1 600 kPa (16 bar) and a maximum temperature of 80 ℃.

Pneumatic fluid power - Compressed air lubricators - Part 1: Main characteristics to be included in supplier's literature and product-marking requirements

ISO 4548-4:1997 内燃机全流式机油滤清器试验方法 第4部分:原始容灰量、滤芯寿命和累积效率(重量法)

This part of ISO 4548 specifies tests for determining the performance of full-flow lubricating oil filters for internal combustion engines as follows. Section 2: Initial particle retention efficiency. This gives the test procedures and parameters for the determination of the initial particle retention efficiency of lubricating oil filter elements under defined test conditions. By reporting the results in accordance with subclause 2.6, the probable retention efficiency for any particle size may be derived. The retention efficiency is determined by the gravimetric method. Section 3: Life and cumulative efficiency. This gives the test procedures and parameters for the determination of element life and cumulative efficiency of lubricating oil filters. The cumulative efficiency is determined by the gravimetric method. NOTE — By agreement between filter manufacturer and purchaser, tests on large filters can be conducted on the basis of tests carried out on filters scaled-down in length. The relationship of the filter flow and test dust addition rate to the effective length of the filter medium should be the same in the scaled-down tests as in the full size filter. For the purposes of this part of ISO 4548, a filter having a test flow rate exceeding 100 l/min is considered large.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 4: Initial particle retention efficiency, life and cumulative efficiency (gravimetric method)

ISO 6301-2:1997 气压传动 压缩空气油雾器 第2部分:测定供应商文件中包含的主要特性的试验方法

This part of ISO 6301 specifies tests, procedures and a method of presenting the results concerning the parameters which define the main characteristics to be included in the supplier's literature of lubricators conforming to ISO 6301-1. The scope of the part of ISO 6301 is: — to facilitate the comparison of lubricators by standardizing test methods and presentation of test data; — to assist in the proper application of lubricators in compressed air systems. The tests specified are intended to allow comparison between the different type of lubricators; and they are not production tests to be carried out on each lubricator manufactured.

Pneumatic fluid power - Compressed air lubricators - Part 2: Test methods to determine the main characteristics to be included in supplier's literature

ISO 4548-1:1997 内燃机全流式机油滤清器试验方法 第1部分:压差/流量特性

This part of ISO 4548 specifies tests for determining the differential pressure/flow characteristics of full-flow lubricating oil filters for internal combustion engines. Tests are specified with oils at two viscosities, one to assess the performance of a filter with a cold oil and the other to assess its performance with an oil at a typical operating temperature.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 1: Differential pressure/flow characteristics

ISO 4548-11:1997 内燃机全流式机油滤清器试验方法 第11部分:自洁式滤清器

This part of ISO 4548 specifies test methods for evaluating the characteristics of self-cleaning oil filters for internal combustion engines. It is applicable to filters in which self-cleaning is continuous or intermittent. The removal of retained particles from the filter is achieved by periodic reversal of the direction of the fluid flow through the elements. However, this also applies mechanical stresses to the filter media. The tests specified in this standard are designed to check the filtration performance of the elements under simulated operating conditions and to confirm their ability to withstand, without damage, variations in oil pressure, temperature, direction of flow and the presence of water. The equipment and procedures specified in this part of ISO 4548 are recommended for fitters having a nominal flow rate of up to 1 600 l/min.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 11: Self-cleaning filters

ISO 4548-3:1997 内燃机全流式机油滤清器试验方法 第3部分:耐高压差和耐高温性

This part of ISO 4548 specifies tests for measuring the resistance to high differential pressure and the resistance to elevated temperatures of filter elements of full-flow lubricating oil filters for internal combustion engines.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 3: Resistance to high differential pressure and to elevated temperature

ISO 4548-2:1997 内燃机全流式机油滤清器试验方法 第2部分:滤芯旁通阀特性

This part of ISO 4548 specifies tests for determining the element by-pass valve characteristics of full-flow lubricating oil filters for internal combustion engines. Tests are specified with oils at two viscosities, one to assess the performance of an element by-pass valve with a cold oil and the other to assess its performance with an oil at a typical operating temperature.

Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 2: Element by-pass valve characteristics

JB/T 8651.3-1997 机床润滑系统元件.微型电动润滑泵

本标准规定了微型电动润滑泵的基本参数、外形及安装尺寸、技术要求、试验方法、验收规则和标志、包装、运输及贮存等。 本标准适用于金属切削机床及锻压机械润滑系统，其他机械的润滑系统亦可参照使用。

Component of machines' lubrication system Minitype electric lubricant pump

JB/T 8651.4-1997 机床润滑系统元件.块式递进式分配器

本标准规定了块式递进式分配器的基本参数及安装尺寸、技术要求、试验方法和验收规则和标志、包装、运输及贮存等。 本标准适用于机床润滑系统，其他机械的润滑系统亦可参照使用。

Component of machines' lubrication system Block type progressive plunger metering devices

JB/T 8522-1997 稀油润滑装置.型式、基本参数与尺寸

本标准规定了稀油润滑装置的型式、基本参数与尺寸。 本标准适用于冶炼、轧制、矿山、电力、石化、建材等机械设备的稀油循环润滑系统的稀油润滑装置。

Diluted oil lubrication unit Type, basic parameters and dimensions

ANSI/ASTM F1567:1997 机加或铸造的自清洁燃料油和润滑油过滤器规范

This specification covers automatic or continuously self-cleaning automatic strainers, or both, for use in fuel and lubrication oil systems. The strainer is designed to operate under positive pressure (discharge side of the pump). Strainers manufactured to this specification are suitable for use in any marine environment.It is not the intent of this document to redefine existing filtration standards. The intent is to provide sound guidelines for purchasers and designers of lube oil and fuel oil systems. Nominal micron requirements and filter efficiencies shall be as agreed upon by the purchaser and manufacturer and stated in the purchase order document.

Specification for Fabricated or Cast Automatic Self-Cleaning, Fuel Oil and Lubricating Oil Strainers

GOST 30541-1997 润滑系统.增压器.技术要求和试验方法

Настоящий стандарт распространяется на смазочные нагнетатели (насосы, насосные агрегаты и станции), предназначенные для создания потока

Lubrication systems. Lubrication deliverers. General technical requirements and test methods

JB/T 8462-1996 双线分配器.40MPa

本标准规定了双线分配器40MPa的型号、基本参数与外形尺寸、技术要求、试验方法、检验规则和标志、标签、包装。 本标准适用于公称压力为40MPa的双线干油集中润滑系统中的双线分配器。

Two-line metering devices 40MPa