23.040.20 塑料管 标准查询与下载

ASTM D2729-21 聚氯乙烯（PVC）污水管和配件的标准规范

1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, chemical resistance, and joint tightness of poly(vinyl chloride) (PVC) sewer and drain pipe and fittings. Perforated pipe is also covered; the joint tightness test is not applicable for perforated pipe. A form of marking to indicate compliance with this specification is also included. 1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

ASTM F1057-21 用热回复技术评定挤压聚氯乙烯（PVC）管质量的标准实施规程

1.1 This practice covers a procedure for estimating the quality of extruded poly (vinyl chloride) (PVC) plastic pipes by observing the reaction of pipe specimens after exposure to hot air in the oven at 180 °C 6 5 °C (356 °F 6 9 °F) for 30 minutes minimum time duration. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Estimating the Quality of Extruded Poly (Vinyl Chloride) (PVC) Pipe by the Heat Reversion Technique

OENORM EN ISO 15874-1:2021 冷热水装置用塑料管道系统 聚丙烯（PP） 第1部分：总则（ISO 15874-1:2013）

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO 15874-1:2013)

ONR CEN/TS 1329-2-2021 建筑结构内用于土壤和废物排放（低温和高温）的塑料管道系统 未增塑聚（氯乙烯）（PVC-U） 第2部分：合格评定指南（CEN/TS 1329-2:2021）

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity (CEN/TS 1329-2:2021)

ASTM F3508-21a 通过压缩配合形状记忆聚合物管（SMPT）的推/拉安装将现场管道翻新为双壁复合管道的标准指南

1.1 This guide describes the specification and reconstruction of in-situ pipelines and conduits 2 in. to 63 in. (50 mm to 1600 mm) diameter) by the pulled-in-place installation, into an existing conduit, of circular, radially reduced, ShapeMemory-Polymer Tubular (SMPT) that after installation, reexpands (by “memory”) to press against the ID of the host pipe, thus coupling the interior pipe, by friction fit, as reinforcement to the host pipe. The added SMPT pipe wall restores leak tightness and adds its strength to the host pipe (Dual-Wall Composite-Pipe). It becomes a continuous compressed-fit dual-wall pipeline. Depending upon the SMPT compound used, the re-constructed pipelines or conduits are suitable for pressure and nonpressure pipeline applications such as process piping, raw and treated water transmission, water pipe systems, forced-mains, industrial and oil-patch gathering and transmission pipelines, sanitary sewers, storm sewers, and culverts. NOTE 1— This standard guide covers circular SMPT tubulars which are radially reduced by mechanical means at the time of installation. This guide does not address “liners” that at the time of manufacture are deformed (folded) into U-shape, C-shape, H-shape, or other such configurations. This guide refers to dual-wall meaning two layers of pipe co-joined in the field, which is different from dual-wall factory-made co-extruded pipe or corrugated pipe. This guide does not provide a complete design basis covering the many variables required for design and construction of this field fabricated product; the advice of professional contractors and/or registered professional engineers may be incorporated as an adjunct to this guide. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. NOTE 2—There are no ISO standards covering the primary subject matter of this guide. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT)

OENORM EN ISO 15874-5:2021 冷热水装置用塑料管道系统 聚丙烯（PP） 第5部分：系统用途适用性（ISO 15874-5:2013 + Amd.1:2018）（合并版）

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO 15874-5:2013 + Amd.1:2018) (consolidated version)

OENORM EN ISO 15874-2:2021 用于热水和冷水装置的塑料管道系统 聚丙烯（PP） 第2部分：管道（ISO 15874-2:2013 + Amd.1:2018）（合并版）

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013 + Amd.1:2018) (consolidated version)

OENORM EN 1329-1-2021 建筑结构内用于土壤和废物排放（低温和高温）的塑料管道系统 未增塑聚（氯乙烯）（PVC-U） 第1部分：管道、配件和系统规范

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system

ASTM F679-21 聚氯乙烯（PVC）大直径塑料重力污水管和配件的标准规范

1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, joining system, and a form of marking for large diameters, 18 to 60 in. poly(vinyl chloride) (PVC) sewer pipe and fittings with integral bell elastomeric seal joints or solvent cemented sockets. 1.2 The requirements of this specification are intended to provide pipe and fittings suitable for nonpressure drainage of sewage and surface water. Pipe and fittings produced to this specification should be installed in accordance with Practice D2321. NOTE 1—Industrial waste disposal lines should be installed only with the specific approval of the governing code authority since temperatures in excess of 140 °F (60 °C) and chemicals not commonly found in drains and sewers may be encountered. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings

DIN EN ISO 11296-4:2021 地下非压力排水和污水管网改造用塑料管道系统 第4部分：现场固化管道衬里（ISO 11296-4:2018 + Amd 1:2021）；德文版 EN ISO 11296-4:2018 + A1:2021

This part of ISO11296 specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks. It applies to the use of various thermosetting resin systems, in combination with compatible fib

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2018 + Amd 1:2021); German version EN ISO 11296-4:2018 + A1:2021

prEN 16904-2021 塑料管道系统 环境产品声明 补充 EN 15804 的产品类别规则，适用于建筑物内的塑料管道系统

Plastics piping systems - Environmental product declarations - Product Category rules complementary to EN 15804, for plastic piping systems inside buildings

prEN 16903-2021 塑料管道系统 环境产品声明 补充 EN 15804 的产品类别规则，用于埋地塑料管道系统

Plastics piping systems - Environmental product declarations - Product Category Rules complementary to EN 15804, for buried plastics piping systems

PN-EN ISO 11296-4-2018-03/A1-2021-10 E 地下无压排水和污水管网改造用塑料管道系统 第4部分：现场养护管衬里 修改件 1：更新了弯曲试验 r 替代表达的定义、标记要求和程序

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks--Part 4: Lining with cured-in-place pipes--Amendment 1: Updated definitions, marking requirements and procedure for alternative expression of flexural test r

UNI/TR 11684-2021 塑料管道系统 根据 UNI EN 13067 和 UNI 9737 的管道焊工资格 理论考试问卷准备指南

Plastic pipes systems - Qualification of welders for pipes according to UNI EN 13067 and UNI 9737 - Guidelines for the preparation of the theoretical exam questionnaire

OENORM EN 1555-2/A-2021 供应气体燃料的塑料管道系统 聚乙烯（PE） 第2部分：管道（国家修正案）

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes (National Amendment)

KS M ISO 14828-2021 玻璃增强热固性塑料（GRP）管 潮湿条件下长期比环松弛刚度的测定和湿松弛系数的计算

Glass-reinforced thermosetting plastics (GRP) pipes－ Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor

KS M 3550-8-2021 下水道管道系统改造用未增塑聚氯乙烯管

Unplasticized polyvinyl chloride tube for renovation of sewer piping system

KS M ISO 9852-2021 未增塑聚氯乙烯（PVC U）管材 规定温度下耐二氯甲烷性能（DCMT） 试验方法

Unplasticized polyvinyl chloride(PVC－U) pipes－ Dichloromethane resistance at specified temperature(DCMT)－Test method

KS M ISO 6259-3-2021 热塑性塑料管材 拉伸性能的测定 第3部分：聚烯烃管材

Thermoplastics pipes－Determination of tensile properties－Part 3：Polyolefin pipes

KS M 3700-1-2021 非承压地下排水、排污用结构壁聚丙烯（PP）管材 第1部分：双壁管材

Structured-wall polypropylene(PP) pipes for non-pressure underground drainage and sewerage－Part 1：Double-wall pipe