23.040.20 塑料管 标准查询与下载

GB/T 13526-1992 硬聚氯乙烯(PVC-U)管材 二氯甲烷浸渍试验方法

本标准规定了硬聚氯乙烯（PVC-U）管材的二氯甲烷浸渍试验方法。本标准作为生产过程的质量控制，用以表征管材的塑化程度和均一性。 本标准适用于各种用途的硬聚氯乙烯（PVC-U）管材。

Unplasticized polyvinyl chloride (PVC-U) pipes--Dichloromethane test

GB/T 13527.2-1992 软聚氯乙烯管(电线绝缘用)

本标准规定了电线绝缘用软聚氯乙烯套管（以下简称软管）的分类、技术要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于以聚氯乙烯树脂为主要原料，经挤出成型的电线绝缘用塑料软管。该软管在常温下主要用于保护电线、电缆。

Plasticized polyvinyl chloride tubing for electrical insulation

GB/T 13020-1991 硬聚氯乙烯(PVC-U)管材 外径和壁厚极限偏差

本标准规定了各种流体输送用圆截面硬聚氯乙烯（PVC-U）管材（以下简称管材）外径和壁厚允许的极限偏差。 本标准适用于各种流体输送用圆截面硬聚氯乙烯（PVC-U）管材。

Unplasticized polyvinyl chloride (PVC-U) pipes--Tolerances on outside diameters and wall thicknesses

GB/T 13019-1991 聚丙烯(PP)管材 外径和壁厚极限偏差

本标准规定了流体输送用圆截面聚丙烯（PP）管材（以下简称管材）的外径和壁厚允许的极限偏差。 本标准适用于外径不超过630mm，符合GB4217的管材。

Polypropylene (PP) pipes--Tolerances on outside diameters and wall thicknesses

GB/T 13018-1991 聚乙烯(PE)管材 外径和壁厚极限偏差

本标准规定了流体输送用圆截面聚乙烯（PE）管材（以下简称管材）的外径和壁厚允许的极限偏差。 本标准适用于外径不超过1200mm，符合GB4217的管材。

Polyethylene (PE) pipes--Tolerances on outside diameters and wall thicknesses

GB 10010-1988 医用软聚氯乙烯管材

本标准规定了医用软聚氯乙烯管材技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于以聚氯乙烯树脂为主要原料，用特定工艺制成的医用软聚氯乙烯管材（以下简称管材）。

Plasticized polyvinyl chloride (PVC) tubing for medical uses

GB/T 9646-1988 硬聚氯乙烯(PVC-U)管材耐丙酮性试验方法

本标准规定了硬聚氯乙烯管材耐丙酮性的试验方法。 本标准适用于各种硬聚氯乙烯管材。

Unplasticized polyvinyl chloride (PVC-U) pipes--Determination of resistance to acetone

GB/T 9645-1988 硬聚氯乙烯(PVC-U)管材吸水性试验方法

本标准规定了硬聚氯乙烯（PVC-U）管材吸水性的试验方法。 本标准适用于各种硬聚氯乙烯管材。

Unplasticized polyvinyl chloride (PVC-U) pipes--Determination of water absorption

GB 9644-1988 硬聚氯乙烯(PVC-U)饮水管材和管件 铅、锡、镉、汞的萃取方法及允许值

本标准规定了硬聚氯乙烯（PVC-U）饮水管材铅、锡、镉、汞的萃取方法及允许值。 本标准适用于输送饮用水的硬聚氯乙烯（PVC-U）管材及管件。

Unplasticized polyvinyl chloride (PVC-U) pipes and fittings for drinking water supply--Extractability of lead tin、cadmium and mercury occurring as impurities--Test method and pemitted levels

GB/T 9643-1988 聚乙烯(PE)管材和管件 熔体流动速率试验方法

本标准规定了测定由聚乙烯制成的管材和管件熔体流动速率的方法。 本标准适用于所有聚乙烯（PE）管材和管件，不论其材料类型和最终用途。

Polyethylene (PE) pipes and fittings--Determination of melt flow rate

GB/T 9642-1988 聚乙烯(PE)管材和管件 根据聚乙烯公称密度和熔体流动速率命名的方法

本标准规定了以制造聚乙烯管材和管件所用的原料命名该聚乙烯管材和管件的方法。 本标准适用于各种用途的聚乙烯管材和管件。其辅料仅包括抗氧剂、稳定剂和必须的料。 本标准不适用于填有玻璃纤维及石棉纤维的聚乙烯管材和管件。

Polyethylene (PE) pipes and fittings--Designation of polyethylene, based on nominal density and melt flow rate

GB/T 8806-1988 塑料管材尺寸测量方法

本标准规定了测量塑料管材尺寸的仪器和方法。 本标准规定下列尺寸的测量： a.任何部位的壁厚，ei； b.平均外径，d； c.任何部位的外径，d

Method for dimension measuring of plastic pipes

GB/T 8805-1988 硬质塑料管材弯曲度测定方法

本标准规定了具有环形截面、公称外径大于32mm的硬质塑料管材的弯曲度测量方法。

Determination of deflection for rigid plastic pipes

GB/T 8801-1988 硬聚氯乙烯(PVC-U)管件坠落试验方法

本标准规定了硬聚氯乙烯管件坠落试验的方法。

Test method for unplasticized PVC fittings by falling

GB/T 7155.2-1987 热塑性塑料管材及管件密度的测定第2部分:聚丙烯管材及管件密度的测定

本标准规定聚丙烯管材及管件密度的测定方法。适用于仅加入抗氧剂或为达到使用寿命所必须的稳定剂的共聚及均聚聚丙烯管材及管件的密度测定。

Determination of density of thermoplastic pipes and fittings--Part 2: Determination of density of polypropylene pipes and fittings

GB/T 7155.1-1987 热塑性塑料管材及管件密度的测定 第1部分:聚乙烯管材及管件基准密度的测定

本标准规定聚乙烯管材及管件基准密度的测定方法。适用于各种用途的聚乙烯管材及管件，其中仅加入抗氧剂或为达到使用寿命所必须的稳定剂。

Determination of density of thermoplastic pipes and fittings--Part 1: Determination of reference density of polyethylene pipes and fittings

ASTM F2658-24 PSM 型聚氯乙烯 (PVC) SDR 51 和 SDR 64 下水道管道和配件的标准规范

1.1  This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, joining systems and a form of marking for type PSM poly(vinyl chloride) (PVC) SDR 51 and SDR 64 sewer pipe and fittings. 1.2  Pipe and fittings produced to this specification should be installed in accordance with Practice D2321 . 1.3  The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5  The following precautionary caveat pertains only to the test methods portion, Section 8 , of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings

ASTM F1734-24 避免聚乙烯（PE）燃气管长期损坏的挤压工具、管道和挤压程序组合鉴定的标准操作规程

1.1  This practice covers qualifying a combination of a squeeze tool, a polyethylene gas pipe, and a squeeze-off procedure to avoid long-term damage in polyethylene gas pipe. Qualifying is conducted by examining the inside and outside surfaces of pipe specimens at and near the squeeze to determine the existence of features indicative of long-term damage. If indicative features are absent, sustained pressure testing in accordance with Test Method D1598 is conducted to confirm the viability of the squeeze-off process. Note 1:  This practice may be useful for evaluating the effects of squeeze-off of other piping materials. If applied to other piping materials, research testing to confirm the applicability of this practice to other materials should be conducted. Note 2:  Qualification of historic pipe should follow the historic version of F1734 closest to the pipe manufactured data. 1.2  This practice is appropriate for any combination of squeeze tool, PE gas pipe, and squeeze-off procedure. 1.3  This practice is for use by squeeze-tool manufacturers and gas utilities to qualify squeeze tools made in accordance with Test Method F1563 ; and squeeze-off procedures based on with Guide F1041 with pipe manufactured in accordance with Specification D2513 . 1.4  Governing codes and project specifications should be consulted. Nothing in this practice should be construed as recommending practices or systems at variance with governing codes and project specifications. 1.5  Where applicable in this practice, “pipe” shall mean “pipe and tubing.” 1.6  Units— The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe

ASTM F2905/F2905M-24 石油和天然气生产用交联聚乙烯（PEX）管线管的标准规范

Standard Specification for Crosslinked Polyethylene (PEX) Line Pipe For Oil and Gas Producing Applications

GSO CEN/TS 1329-2:2024 建筑结构内污物和废物排放（低温和高温）塑料管道系统 未增塑聚氯乙烯（PVC-U） 第2部分：合格评定指南

This document gives requirements and guidance for the assessment of conformity of formulations, products and assemblies in accordance with EN 1329-1 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures. NOTE 1 The quality management system is expected to conform to or is no less stringent than the relevant requirements to EN ISO 9001 [1]. NOTE 2 If third party certification is involved, the certification body is expected to be compliant with either EN ISO/IEC 17065 [2] or EN ISO/IEC 17021-series [3], as applicable. NOTE 3 In order to help the reader, a basic test matrix is given in Annex A. In conjunction with EN 1329-1, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC-U) intended for soil and waste discharge systems (low and high temperature): - inside buildings (application area code "B"); - both inside buildings and buried in ground within the building structure (application area code "BD").

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity