23.040.20 塑料管 标准查询与下载

ISO/CD 15875-5:2023 冷热水装置用塑料管道系统 交联聚乙烯 (PE-X) 第 5 部分：系统用途的适用性

Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system

ISO/PRF 10468:2023 玻璃增强热固性塑料（GRP）管 湿或干条件下环蠕变性能的测定

Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions

ISO/CD 15875-2:2023 冷热水装置用塑料管道系统 交联聚乙烯 (PE-X) 第 2 部分：管道

Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes

ISO 10468:2023 玻璃增强热固性塑料（GRP）管 湿或干条件下环蠕变性能的测定

Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions

T/CSTE 0348-2023 质量分级及“领跑者”评价要求 给水用丙烯酸酯共混聚氯乙烯管材

本文件规定了给水用丙烯酸酯共混聚氯乙烯管材产品质量及企业标准水平的基本要求、评价指标及要求、评价方法及等级划分。 本文件适用于给水用丙烯酸酯共混聚氯乙烯管材产品质量及企业标准水平评价。

Assessment requirements for quality grading and forerunner - Acrylate blended PVC pipes for water supply

ISO/FDIS 16422-2:2023 用于在压力下输送水的由定向未增塑聚氯乙烯（PVC-O）制成的管道和接头 第 2 部分：管道

Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 2: Pipes

ISO/FDIS 16422-5:2023 用于在压力下输送水的由定向未增塑聚氯乙烯（PVC-O）制成的管道和接头 第 5 部分：系统用途的适用性

Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 5: Fitness for purpose of the system

ISO/FDIS 16422-1:2023 用于在压力下输送水的由定向未增塑聚氯乙烯（PVC-O）制成的管道和接头 第 1 部分：概述

Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 1: General

T/QYNY 001-2023 耐热聚乙烯（PE-RT II型）供热管道工程技术规程

1、为规范Ⅱ型耐热聚乙烯（以下简称PE-RT Ⅱ型）供热管道在低温供热领域的应用，做到技术先进、经济合理、安全运行和保证工程质量，特制定本规程。 2、本规程适用于工作压力不大于1.25MPa（仅适用于S4/SDR9系列管材且介质温度小于45℃下的工况）、设计温度不大于75℃、公称外径小于或等于355mm的PE-RT Ⅱ型供热管道工程的设计、施工及验收。 3、PE-RT Ⅱ型供热管道工程的设计、施工及验收，除应符合本规程外，尚应符合国家现行有关标准的规定。

Technical specification for heating pipe engineering of polyethylene of raised temperature resistance（PE-RT II）

GSO EN 1329-1:2023 建筑结构内用于土壤和废物排放（低温和高温）的塑料管道系统 未增塑聚氯乙烯 (PVC-U) 第1部分：管道、配件和系统规范

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems intended for soil and waste discharge applications (low and high temperature): - inside buildings (application area code "B"); - for both inside buildings and buried in ground within the building structure (application area code "BD"). NOTE 1 The intended use is reflected in the marking of products by "B" or "BD". NOTE 2 Application "B" covers uses above ground inside the building, or outside buildings fixed onto the wall. NOTE 3 Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 1453-1 [1]. NOTE 4 For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm. NOTE 5 EN 476 [2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements. This document is also applicable to PVC-U pipes, fittings and the system intended for the following purposes: - ventilating part of the pipework in association with discharge applications; - rainwater pipework within the building structure. This document also specifies the test parameters for the test methods that are referred to. This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours. NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 26.

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system

ASTM F1173-01(2023) 船用热固性树脂玻璃纤维管道系统的标准规范

1.1 This specification covers reinforced thermosetting resin pipe systems with nominal pipe sizes (NPS) 1 in. through 48 in. (25 mm through 1200 mm) which are to be used for all fluids approved by the authority having jurisdiction in marine piping systems. 1.2 The dimensionless designator NPS has been substituted for traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains to the test methods which are included in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications

ASTM F1365-91(2023) 使用柔性弹性密封的塑料地下管道接头的抗渗水性的标准试验方法

1.1 This test method covers the determination of the water infiltration resistance of gasketed plastic underground conduit joints using a pressurized water bladder apparatus. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals

ASTM F3128-23 带蜂窝芯的聚氯乙烯（PVC）表40排水管、废水管和通风管的标准规范

1.1 This specification covers coextruded poly(vinyl chloride) (PVC) plastic drain, waste and vent pipe made to Schedule 40 iron pipe sizes (IPS) and produced by the coextrusion process with concentric inner and outer solid PVC layers and the core consisting of closed-cell cellular PVC. Plastic which does not meet the material requirements specified in Section 5 is excluded from single layer and all coextruded layers. 1.2 Fittings meeting the requirements of Specification D2665 and D3311 are suitable for use with pipe meeting the requirements of this specification. 1.3 Poly(vinyl chloride) plastic which does not meet the definitions of virgin PVC plastic as given in 5.1 is excluded, as performance of plastic other than those defined as virgin was not determined. PVC rework plastic which meets the requirements of rework plastic as given in 5.2 is acceptable. 1.4 Reprocessed plastic or recycled plastic as defined in Terminology D883 is excluded. 1.5 Recommendations for storage, joining and installation are provided in Appendix X1, Appendix X2, and Appendix X3 respectively. 1.6 The text of this specification references notes, footnotes and appendices which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core

ISO 161-1:2018/Amd 1:2023 输送流体用热塑塑料管.公称外径和公称压力.第1部分:米制系列 修改件1

Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 1: Metric series — Amendment 1

CSA B137.19-2023 用于燃气服务的交联聚乙烯 (PEX) 管道系统

1 Scope 1.1 General This Standard covers crosslinked polyethylene (PEX) pipe and fittings for use in gas mains and services, including gas gathering, gas transmission, and distribution of fuel gases. 1.2 Pipe This Standard covers PEX pipes in metric nominal sizes DN 16 to DN 1000 or nominal pipe sizes NPS-3 to NPS-54 that are a) pressure-rated using the hydrostatic design basis (HDB) rating method specified in ASTM D2837 or the minimum required strength (MRS) rating method specified in ISO 9080 and ISO 12162; b) intended for operating temperatures between –50 and 110 °C; and c) joined by PEX electrofusion fittings or by mechanical fittings, but not by butt fusion. 1.3 Joints This Standard includes requirements for joints made between PEX pipe and PE electrofusion fittings compliant with ASTM F3373. 1.4 Pipe exclusions This Standard does not cover pipes intended to be joined by butt fusion, socket fusion, or saddle fusion. 1.5 Fittings Fittings to be used with PEX pipe manufactured to this Standard are in accordance with ASTM F2829. Fittings covered in this Standard include a) plastic-to-metal transition fittings; b) electrofusion fittings (e.g., couplings, elbows, tees, and end caps); and c) mechanical couplings. 1.6 Requirements This Standard specifies requirements for a) primary properties of the PE compound; b) physical properties of the finished PEX pipe; c) on-line monitoring during production; d) shipping and storage; and e) markings. Note: See CSA Z662 for design and installation limitations of products covered by this Standard. 1.7 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Crosslinked polyethylene (PEX) piping systems for gas services

23/30433901 DC BS ISO 11619 气动流体动力 聚氨酯和聚酰胺管主要用于气动装置 尺寸规格

BS ISO 11619. Pneumatic fluid power. Polyurethane and polyamide tubings for use primarily in pneumatic installations. Dimensions and specification

23/30470178 DC BS ISO 9854-2.2 用于输送流体的热塑性塑料管道 夏比冲击性能的测定 第 2 部分：各种材料管道的试验条件

BS ISO 9854-2.2. Thermoplastics pipes for the transport of fluids. Determination of Charpy impact properties - Part 2. Test conditions for pipes of various materials

ASTM F1483-23 定向聚氯乙烯（PVCO）压力管标准规范

1.1 This specification covers requirements for materials, dimensions, sustained pressure, accelerated regression testing, burst pressure, flattening, impact resistance, workmanship, solvent cement joint testing, and methods of marking for oriented poly(vinyl chloride) (PVCO) pipe for pressure applications. 1.2 The PVCO pipe shall be joined using either elastomeric seals (gaskets) or solvent cement with primer. The gasketed joint shall meet the requirements of Specification D3139 and the elastomeric seal shall meet the requirements of Specification F477. The solvent cemented joint shall meet the requirements of 5.3.3. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test method portion, Section 7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe

ASTM F876-23 交联聚乙烯（PEX）管材标准规范

1.1 This specification covers crosslinked polyethylene (PEX) tubing that incorporates an optional polymeric inner, middle or outer layer and that is outside diameter controlled, made in nominal SDR9 tubing dimension ratios except where noted, and pressure rated for water at three temperatures (see Appendix X1). Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, excessive temperature and pressure, environmental stress cracking, stabilizer functionality, bent-tube hydrostatic pressure, oxidative stability in potable chlorinated water, UV resistance, and degree of crosslinking. Requirements for tubing markings are also given. The components covered by this specification are intended for use in, but not limited to, residential and commercial, hotand cold-potable water distribution systems, reclaimed water, fire protection, municipal water service lines, building supply lines, radiant heating and cooling systems, hydronic distribution systems, snow and ice melting systems, geothermal ground loops, district heating, turf conditioning, compressed air distribution and building services pipe, provided that the PEX tubing covered herein complies with applicable code requirements. 1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. The values given in parentheses are mathematical conversions that may not be exact equivalents to either SI units or inch-pound units and that are provided for information only. 1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Crosslinked Polyethylene (PEX) Tubing

ASTM F442/F442M-23 氯化聚氯乙烯塑料管（SDR–PR）标准规范

1.1 This specification covers chlorinated poly(vinyl chloride) (CPVC) pipe made in standard thermoplastic pipe dimension ratios and pressure rated for water (see Appendix X1). Included are criteria for classifying CPVC plastic pipe materials and CPVC plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, burst pressure, flattening, and extrusion quality. Methods of marking are also given. NOTE 1—The CPVC pipe covered by this specification was covered previously in Specification D2241. NOTE 2—The sustained and burst pressure test requirements and the pressure ratings in the Appendix X1 are calculated from stress values obtained from tests made on pipe 2 in. [50 mm] and smaller. However, tests on larger pipe have shown these stress values to be valid. 1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing. NOTE 3—Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards should a system fail for any reason. 1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Within the text, the SI units are shown in brackets. 1.5 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in 8.4.1. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR–PR)