23.040.20 塑料管 标准查询与下载

ASTM F2817-13(2023) 维护或修理用聚氯乙烯气体压力管和配件的标准规范

Standard Specification for Poly (Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings For Maintenance or Repair

ASTM D3681-23 偏转条件下“玻璃纤维”（玻璃纤维增强热固性树脂）管道耐化学性的标准试验方法

1.1 This test method covers the procedure for determining the chemical-resistant properties of fiberglass pipe in a deflected condition for diameters 4 in. (102 mm) and larger. Both glass–fiber–reinforced thermosetting resin pipe (RTRP) and glass–fiber–reinforced polymer mortar pipe (RPMP) are fiberglass pipes. NOTE 1—For the purposes for this standard, polymer does not include natural polymers. 1.2 Inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 9.5. NOTE 2—There is no known ISO equivalent to this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition

ASTM F2986-12(2023) 矿井渗滤液用波纹聚乙烯管和配件标准规范

Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications

ASTM F2896-23 石油、天然气和危险液体运输用增强聚乙烯复合管标准规范

Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids

ASTM F3203-19(2023) 交联聚乙烯（PEX）管材凝胶含量测定的标准试验方法

Standard Test Method for Determination of Gel Content of Crosslinked Polyethylene (PEX) Pipes and Tubing

ISO 8513:2023 塑料管道系统 玻璃增强热固性塑料（GRP）管 测定初始纵向拉伸强度的试验方法

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength

ISO/PRF 8513:2023 塑料管道系统 玻璃增强热固性塑料（GRP）管 测定初始纵向拉伸强度的试验方法

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength

ISO/CD 15875-5:2023 冷热水装置用塑料管道系统 交联聚乙烯 (PE-X) 第 5 部分：系统用途的适用性

Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system

ISO/PRF 10468:2023 玻璃增强热固性塑料（GRP）管 湿或干条件下环蠕变性能的测定

Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions

ISO/CD 15875-2:2023 冷热水装置用塑料管道系统 交联聚乙烯 (PE-X) 第 2 部分：管道

Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes

ISO 10468:2023 玻璃增强热固性塑料（GRP）管 湿或干条件下环蠕变性能的测定

Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions

T/CSTE 0348-2023 质量分级及“领跑者”评价要求 给水用丙烯酸酯共混聚氯乙烯管材

本文件规定了给水用丙烯酸酯共混聚氯乙烯管材产品质量及企业标准水平的基本要求、评价指标及要求、评价方法及等级划分。 本文件适用于给水用丙烯酸酯共混聚氯乙烯管材产品质量及企业标准水平评价。

Assessment requirements for quality grading and forerunner - Acrylate blended PVC pipes for water supply

ISO/FDIS 16422-2:2023 用于在压力下输送水的由定向未增塑聚氯乙烯（PVC-O）制成的管道和接头 第 2 部分：管道

Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 2: Pipes

ISO/FDIS 16422-5:2023 用于在压力下输送水的由定向未增塑聚氯乙烯（PVC-O）制成的管道和接头 第 5 部分：系统用途的适用性

Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 5: Fitness for purpose of the system

ISO/FDIS 16422-1:2023 用于在压力下输送水的由定向未增塑聚氯乙烯（PVC-O）制成的管道和接头 第 1 部分：概述

Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 1: General

T/QYNY 001-2023 耐热聚乙烯（PE-RT II型）供热管道工程技术规程

1、为规范Ⅱ型耐热聚乙烯（以下简称PE-RT Ⅱ型）供热管道在低温供热领域的应用，做到技术先进、经济合理、安全运行和保证工程质量，特制定本规程。 2、本规程适用于工作压力不大于1.25MPa（仅适用于S4/SDR9系列管材且介质温度小于45℃下的工况）、设计温度不大于75℃、公称外径小于或等于355mm的PE-RT Ⅱ型供热管道工程的设计、施工及验收。 3、PE-RT Ⅱ型供热管道工程的设计、施工及验收，除应符合本规程外，尚应符合国家现行有关标准的规定。

Technical specification for heating pipe engineering of polyethylene of raised temperature resistance（PE-RT II）

GSO EN 1329-1:2023 建筑结构内用于土壤和废物排放（低温和高温）的塑料管道系统 未增塑聚氯乙烯 (PVC-U) 第1部分：管道、配件和系统规范

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems intended for soil and waste discharge applications (low and high temperature): - inside buildings (application area code "B"); - for both inside buildings and buried in ground within the building structure (application area code "BD"). NOTE 1 The intended use is reflected in the marking of products by "B" or "BD". NOTE 2 Application "B" covers uses above ground inside the building, or outside buildings fixed onto the wall. NOTE 3 Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 1453-1 [1]. NOTE 4 For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm. NOTE 5 EN 476 [2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements. This document is also applicable to PVC-U pipes, fittings and the system intended for the following purposes: - ventilating part of the pipework in association with discharge applications; - rainwater pipework within the building structure. This document also specifies the test parameters for the test methods that are referred to. This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours. NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 26.

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system

ASTM F1173-01(2023) 船用热固性树脂玻璃纤维管道系统的标准规范

1.1 This specification covers reinforced thermosetting resin pipe systems with nominal pipe sizes (NPS) 1 in. through 48 in. (25 mm through 1200 mm) which are to be used for all fluids approved by the authority having jurisdiction in marine piping systems. 1.2 The dimensionless designator NPS has been substituted for traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains to the test methods which are included in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications

ASTM F1365-91(2023) 使用柔性弹性密封的塑料地下管道接头的抗渗水性的标准试验方法

1.1 This test method covers the determination of the water infiltration resistance of gasketed plastic underground conduit joints using a pressurized water bladder apparatus. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals

ASTM F3128-23 带蜂窝芯的聚氯乙烯（PVC）表40排水管、废水管和通风管的标准规范

1.1 This specification covers coextruded poly(vinyl chloride) (PVC) plastic drain, waste and vent pipe made to Schedule 40 iron pipe sizes (IPS) and produced by the coextrusion process with concentric inner and outer solid PVC layers and the core consisting of closed-cell cellular PVC. Plastic which does not meet the material requirements specified in Section 5 is excluded from single layer and all coextruded layers. 1.2 Fittings meeting the requirements of Specification D2665 and D3311 are suitable for use with pipe meeting the requirements of this specification. 1.3 Poly(vinyl chloride) plastic which does not meet the definitions of virgin PVC plastic as given in 5.1 is excluded, as performance of plastic other than those defined as virgin was not determined. PVC rework plastic which meets the requirements of rework plastic as given in 5.2 is acceptable. 1.4 Reprocessed plastic or recycled plastic as defined in Terminology D883 is excluded. 1.5 Recommendations for storage, joining and installation are provided in Appendix X1, Appendix X2, and Appendix X3 respectively. 1.6 The text of this specification references notes, footnotes and appendices which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core