25.220.60 标准查询与下载

BS EN 13523-24:2004 卷材覆层金属.试验方法.耐粘结性和压力标记

This part of EN 13523 describes the procedure for determining the resistance to blocking and/or pressure marking of an organic coating on a metallic substrate.

Coil coated metals - Test methods - Resistance to blocking and pressure marking

BS EN 13523-19:2004 卷材覆层金属.试验方法.大气曝露试验的样板设计和方法

This part of EN 13523 specifies the panel design and describes the procedure for determining the resistance to outdoor exposure of an organic coating on a metallic substrate.

Coil coated metals - Test methods - Panel design and method of atmospheric exposure testing

SAE AMS3278-2004 密封和涂层化合物：聚氨酯（PUR）耐燃料高抗拉强度/整体燃料箱/燃料腔/通用的伸长率

This specification covers polyurethane (PUR) in the form of two-component sealing compounds. This product has been used typically for contact with fuels, but usage is not limited to such applications. Each application should be considered separately. This polyurethane (PUR) has a service temperature range of -65 to +250 degrees F (-54 to 121 degrees C) with a continuous fuel service temperature range of -65 to +160 degrees F (-54 to +71 degrees C). It may be used for faying surface sealing, wet-installation of fasteners, overcoat of fasteners, sealing joints and seams and, in some cases, as a non-structural adhesive. NOTE: The use of an adhesion promoter shall be required to obtain proper adhesion.

Sealing and Coating Compound: Polyurethane (PUR) Fuel Resistant High Tensile Strength/Elongation for Integral Fuel Tanks/Fuel Cavities/General Purpose

SY/T 0061-2004 埋地钢质管道外壁有机防腐层技术规范

为规范管道外壁有机防腐层设计、施工及验收、保证外防腐层的经济性、合理性及管道在役期间的运行安全、特制定本标准。 本标组合弄规定了埋地钢质管道（以下简称管道）外壁有机防腐层设计、施工及验收的基本原则，适用于陆上油气田管道和长输管道外壁防腐层的设计、施工及验收。 管道外壁有机防腐层设计、施工及验收除应执行本标准外，尚应符合国家现行有关强制性标准的规定。

Technical specification of external protective organic coating for buried steel pipeline

JB/T 10458-2004 机械设备抗高温氧化涂层 技术条件

本标准规定了在80℃~400℃温度范围内，钢铁基体表面抗高温氧化腐蚀的保护性有机或有机无机复合涂层的涂装要求和检验方法。 　　本标准适用于机械设备钢铁表面抗高温氧化保护涂层。本标准不适用于在使用温度下基体产生变形的制品。

Specification of anti-oxidizing coating at high-temperature for machineries

EN 13523-24:2004 卷材覆层金属的试验方法.第24部分:耐粘结性和压力标记

This part of EN 13523 describes the procedure for determining the resistance to blocking and/or pressure marking of an organic coating on a metallic substrate.

Coil coated metals - Test methods - Part 24: Resistance to blocking and pressure marking

ASTM D7093-04 双轴拉伸穹面上钢的有机涂层薄膜的可成形性的标准试验方法

1.1 This test method covers the evaluation of the formability and adhesion of factory applied thin film organic coatings on steel with thicknesses of 2.5 to 10 microns (0.10 to 0.40 mils) typical of those used in the coil coating industry.1.2 The degree of oil removal prior to forming, the techniques of taping, and differences in adhesive strength of the tape can affect the adhesion rating.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 7.

Standard Test Method for Formability of Thin Film Organic Coatings on Steel Over a Biaxially Stretched Dome

EN 13523-16:2004 卷材覆层金属的试验方法.第16部分:耐磨性

This part of EN 13523 describes the procedure for determining the resistance to abrasion and wear of an organic coating on a metallic substrate.

Coil coated metals - Test methods - Part 16: Resistance to abrasion

BS EN 13523-21:2003 卷材覆层金属.试验方法.室外暴露板的评定

This Part of this European Standard specifies the procedure for evaluating the behaviour of an organic coating on a metallic substrate during and after outdoor exposure. Panel design, preparation and the procedure for outdoor exposure are to be performed in accordance with prEN 13523-19. After washing of the panel some dirt can remain on the panel. This remaining dirt can influence the accuracy and precision of readings of gloss and colour, performed on exposed panels, although carried out in accordance with the standards. Unlike other precise measurements, the objective of this Part of this European Standard is to report on trends in the corrosion and/or paint degradation behaviour of coil coated panels.

Coil coated metals - Test methods - Evaluation of outdoor exposed panels

BS EN 13523-22:2003 卷材覆层金属.试验方法.色差.视觉比较

This Part of EN 13523 describes the procedure for determining the difference in the colour of an organic coating on a metallic substrate by visual comparison against a standard using either diffuse natural daylight or artificial daylight in a standard booth. NOTE Results may differ between natural and artificial daylight. It may occur that two colour specimens will match in daylight but not under another light source. This phenomenon is known as metamerism (see EN 13523-15). In case a metameric match is to be reported in objective terms, spectrophotometric measurements (using CIE Standard Illuminants D65 and A) should be made, in accordance with EN 13523-15. No statement is made about either the precision or the accuracy of this procedure since the results derived are neither in numerical form nor do they provide a pass/fail evaluation in objective terms. Therefore, this procedure should only be used where the use of colour measuring instruments is not recommendable (evaluation of colour matches, inspection of metallic colours etc.). Although colour measuring instruments should be used where possible, in some cases a visual comparison can be useful (evaluation of colour matches, inspection of metallic colours etc.). The standardization of such visual comparisons, by light sources, illuminating and viewing geometry and specimen size, provides for improved uniformity of results. This practice is essential for critical colour matching and is highly recommended for colour inspections.

Coil coated metals - Test methods - Colour difference - Visual comparison

CAN/CSA-Z245.20-02/Z245.21-2002 钢管外热熔环氧涂层/管道聚乙烯外涂层

Z245.20-02 1. Domaine d?application 1.1 Cette norme vise la qualification, l?application, l?inspection, la mise à l?essai, la manutention et l?entreposage des matériaux nécessaires à l?application en usine d?un enduit extérieur en époxyde thermofusible (EÉT) sur des tuyaux en acier destinés surtout aux oléoducs et aux gazoducs enfouis ou submergés. 1.2 Cette norme ne vise pas les systèmes de revêtement EÉT à deux types poudres ni les systèmes de revêtement EÉT à haute température (température de transition vitreuse supérieure à 110 °C). 1.3 Dans cette norme, le terme "doit" indique une exigence, c?est-à-dire une prescription que l?utilisateur doit respecter pour assurer la conformité à la norme; "devrait" indique une recommandation ou ce qu?il est conseillé mais non obligatoire de faire et "peut" une possibilité ou un conseil. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les légendes des figures et des équations font également partie de celles-ci.

Exterior Hot Melt Epoxy Coating for Steel Pipes / Exterior Polyethylene Coating for Pipes

NP EN 13523-1-2002 金属涂层线圈．测试方法．第1部分：涂层厚度

Esta parte da norma especifica os procedimentos para determina??o da espessura de um revestimento org?nico sobre um substrato metálico, usando dispositivos eléctricos de medi??o. Nesta parte da EN 13523 s?o apresentados dois métodos adequados para: a) medi??o de espessura sobre substrato ferromagnético, por exemplo a?o laminado a frio e a?o com revestimento metálico. b) medi??o de espessura sobre substrato n?o ferromagnético, por exemplo alumínio e as suas ligas. Os métodos s?o aplicáveis somente a produtos com substratos planos e lisos, mas o próprio revestimento pode ser texturado. Neste caso a média de uma série de leituras representará uma média da espessura do revestimento org?nico. Os métodos n?o s?o aplicáveis a espessuras de revestimento inferiores a 3 um.

Coil coated metals Test methods Part 1:Coating thickness

NP EN 13523-2-2002 金属涂层线圈．测试方法．第2部分：反射的光泽

Esta parte da norma especifica os procedimentos para a determina??o do brilho especular de um revestimento org?nico aplicado sobre substrato metálico. O brilho é uma característica de import?ncia fundamental no aspecto das bandas metálicas pré-revestidas. O equipamento exige uma amostra plana de dimens?es superiores à abertura, pelo que n?o podem ser medidas superfícies irregulares. Este método é aplicável a todos os revestimentos pigmentados e n?o pigmentados, incluindo os revestimentos metálicos/nacarados. Contudo, para revestimentos texturados, é apenas indicativo.

Coil coated metals Test methods Part 2:Specular gloss

NP EN 13523-0-2002 金属涂层线圈．测试方法．第0部分：测试方法清单及一般介绍

Coil coated metals Test methods Part 0:General introduction and list of test methods

NP EN 13523-5-2002 金属涂层线圈．测试方法．第5部分：快速变形的阻抗力（碰撞测试）

Esta parte da Norma especifica um procedimento para a determina??o da resistência à fissura??o e/ou destacamento por deforma??o rápida de um revestimento org?nico aplicado sobre um substrato metálico, em termos da energia que a amostra possa suportar. A espessura do revestimento a ensaiar deve ser de 60 |um no máximo. O método de ensaio n?o é recomendado para revestimentos de espessura superior a 60 u.m devido à falta de significado dos resultados.

Coil coated metals Test methods Part 5:Resistance to rapid deformation(impact test)

NP EN 13523-3-2002 金属涂层线圈．测试方法．第3部分：色差-使用仪器比较

Esta parte da norma especifica os procedimentos para a determina??o instrumental da diferen?a de cor de um revestimento org?nico de bandas metálicas pré-revestidas. O estabelecimento de padr?es, assim como a magnitude de uma diferen?a de cor aceitável, n?o est?o abrangidos por este método. Nesta parte da EN 13523 s?o apresentados dois métodos adequados: a) medi??o instrumental da diferen?a de cor usando um colorímetro tristimulus. b) medi??o instrumental da diferen?a de cor usando um espectrofotómetro ou equivalente. Est?o excluídas deste método as amostras que produzem fluorescência, mostrem metamerismo significativo ou que sejam multi-coloridas, nacaradas ou metalizadas. Para determinar se existe metamerismo, é determinado o índice de metamerismo (veja-se EN 13523-15) e/ou uma observa??o visual (veja-se o documento em prepara??o, WI 00139156, Parte 22 desta Norma) realizada com diferentes fontes de luz artificial.

Coil coated metals Test methods Part 3:Colour difference-Instrumental comparison

JB/T 10394.3-2002 涂装设备通用技术条件.第3部分:涂层

本部分规定了涂装设备层的技术要求、涂层质量、检验项目及检验方法。 　　本部分适用于各种涂装设备及其零部件的涂层。

General technical conditions for painting equipment Part 3:Coating

NF T37-001-23:2002 镀层盘材金属.试验方法.第23部分:在含二氧化硫的潮湿环境中测定颜色的稳定性

Coil coated metals - Test methods - Part 23 : colour stability in humid atmospheres containing sulfur dioxide.

NF T37-001-6:2002 镀层盘材金属.试验方法.第6部分:压痕后的附着力(杯突试验)

Coil coat metals - Test methods - Part 6 : adhesion after indentation (cupping test).

NF T37-001-15:2002 镀层盘材金属.试验方法.第15部分:位变异构

Coil coated metals - Test methods - Part 15 : metamerism.