25.220.60 标准查询与下载

SAE AMS3278A-2008 密封和涂料混合物:通用整体燃料罐/燃料腔用耐高拉伸强度/延伸的聚氨酯(PUR)燃料

This specification covers polyurethane (PUR) in the form of two-component sealing compounds. This product has been used typically for contact with fuels, but usage is not limited to such applications. Each application should be considered separately. This polyurethane (PUR) has a service temperature range of -65 to +250 °F (-54 to 121 °C) with a continuous fuel service temperature range of -65 to +160 °F (-54 to +71 °C). It may be used for faying surface sealing, wet-installation of fasteners, overcoat of fasteners, sealing joints and seams and, in some cases, as a non-structural adhesive. NOTE: The use of an adhesion promoter shall be required to obtain proper adhesion.

Sealing and Coating Compound: Polyurethane (PUR) Fuel Resistant High Tensile Strength / Elongation For Integral Fuel Tanks / Fuel Cavities / General Purpose

DIN EN 14879-4:2008 防止工业装置和设备受侵入介质腐蚀的有机涂覆系统和衬料.第4部分:金属构件衬料

This document describes the requirements for and methods of testing of organic linings which are applied to metallic process engineering equipment that will come in contact with chemical substances The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners. The standard applies to linings which serve one or more of the following purposes: -- to protect the component from adverse effects of aggressive substances; -- to protect waters (e.g. ground water) from harmful substances; -- to protect the charge from becoming contaminated by components released from the substrate material; -- to achieve a particular surface quality. This standard applies to vessels, apparatus, piping parts and other components for process plants made of metallic substrate materials which are in contact with media and are provided with a surface protection made of a) prefabricated, natural or synthetic rubber based sheeting (subsequently named rubber lining), to be applied in the workshop or on site; b) prefabricated, phenol formaldehyde or epoxy resin based sheeting (subsequently named duroplastic lin- ing), to be applied in the workshop only; c) prefabricated, thermoplastic products (e.g. foils, sheeting, plates, pipes) (subsequently named thermo- plastic lining), to be applied in the workshop or on site. The standard specifies the requirements, acceptance inspection, packaging, transport, storage and installation of organic linings for metallic materials. The tests described in this standard are intended for verification of the suitability of sheeting used for linings and for acceptance inspection to be carried out on the products during or after application of the lining or as part of routine inspections to determine any changes effected in the lining during service.

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components; English version of DIN EN 14879-4:2008-01

DIN EN 13438 Berichtigung 1:2007 涂料和清漆.建筑用镀锌或镀锌粉钢产品用粉末有机涂层.技术勘误DIN EN 13438-2006

Paints and varnishes - Powder organic coatings for galvanized or sherardised steel products for construction purposes; German version EN 13438:2005, Corrigenda to DIN EN 13438:2006-01

LST EN 14879-4-2007 保护工业设备和工厂免受侵蚀性介质腐蚀的有机涂层系统和衬里 第4部分：金属部件上的衬里

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components

LST EN 14879-5-2007 保护工业设备和工厂免受侵蚀性介质腐蚀的有机涂层系统和衬里 第5部分：混凝土构件上的衬里

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components

DS/EN 14879-5:2007 保护工业设备和工厂免受侵蚀性介质腐蚀的有机涂层系统和衬里 第5部分：混凝土构件上的衬里

This document describes the requirements for and methods of testing of organic linings which are applied to concrete process engineering equipment that will come in contact with aggressive chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners).The standard applies to linings which serve one or more of the following purposes:- to protect the component from damaging effects of aggressive substances;- to protect waters (e.g. ground water) from harmful substances;- to protect the charge from becoming contaminated by components released from t

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components

DS/EN 14879-4:2007 保护工业设备和工厂免受侵蚀性介质腐蚀的有机涂层系统和衬里 第4部分：金属部件上的衬里

This document describes the requirements for and methods of testing of organic linings which are applied to metallic process engineering equipment that will come in contact with chemical substances. The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners )).The standard applies to linings which serve one or more of the following purposes:- to protect the component from adverse effects of aggressive substances;- to protect waters (e.g. ground water) from harmful substances;- to protect the charge from becoming contaminated by components released from the substrate material;- to achieve a p

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components

ASTM D4708-07 制备有机涂料均匀自由膜的标准实践

Free films are required for conducting tests to evaluate physical properties such as tensile and elongation (Test Method D 2370), moisture vapor permeability (Test Methods D 1653), and other physical properties of organic coatings where the substrate may interfere with the determination.1.1 This practice covers the preparation of free films of organic coatings for use in determining the physical properties of the coatings. Procedures are given for preparing free films on three alternative substrates. These substrates are treated FEP (fluorinated ethylene-propylene) sheet, silicone coated paper, and halosilane coated glass plates. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Preparation of Uniform Free Films of Organic Coatings

DIN EN 14879-5:2007 防止侵蚀物体腐蚀工业装置和设备用有机涂层系统和衬料.第5部分:混凝土构件衬料

This document describes the requirements for and methods of testing of organic linings which are applied to concrete process engineering equipment that will come in contact with aggressive chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners). The standard applies to linings which serve one or more of the following purposes: -- to protect the component from damaging effects of aggressive substances; -- to protect waters (e.g. ground water) from harmful substances; -- to protect the charge from becoming contaminated by components released from the substrate material; -- to achieve a particular surface quality. The different lining systems are: a) bonded linings; b) mechanically fixed linings; c) loose linings of sheeting material; d) loose linings of pre-formed pieces or lining units. Handling of aggressive or water pollutant materials is understood to include e) storage; f) filling; g) loading and unloading; h) manufacture; i) treatment; j) use.

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components; German version EN 14879-5:2007

NF T34-801-5*NF EN 14879-5:2007 防止工业装置和设备受侵入介质腐蚀的有机涂层系统和衬料.第5部分:混凝土构件衬料

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggresive media - Part 5 : linings on concrete components.

BS EN 14879-4:2007 防止工业装置和设备受侵入介质腐蚀的有机涂层系统和衬料.金属构件衬料

This document describes the requirements for and methods of testing of organic linings which are applied to metallic process engineering equipment that will come in contact with chemical substances. The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners1)). The standard applies to linings which serve one or more of the following purposes:  to protect the component from adverse effects of aggressive substances;  to protect waters (e.g. ground water) from harmful substances;  to protect the charge from becoming contaminated by components released from the substrate material;  to achieve a particular surface quality. This standard applies to vessels, apparatus, piping parts and other components for process plants made of metallic substrate materials which are in contact with media and are provided with a surface protection made of a) prefabricated, natural or synthetic rubber based sheeting (subsequently named rubber lining), to be applied in the workshop or on site; b) prefabricated, phenol formaldehyde or epoxy resin based sheeting (subsequently named duroplastic lining), to be applied in the workshop only; c) prefabricated, thermoplastic products (e.g. foils, sheeting, plates, pipes) (subsequently named thermoplastic lining), to be applied in the workshop or on site. The standard specifies the requirements, acceptance inspection, packaging, transport, storage and installation of organic linings for metallic materials. The tests described in this standard are intended for verification of the suitability of sheeting used for linings and for acceptance inspection to be carried out on the products during or after application of the lining or as part of routine inspections to determine any changes effected in the lining during service.

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Linings on metallic components

BS EN 14879-5:2007 防止工业装置和设备受侵入介质腐蚀的有机涂层系统和衬料.混凝土构件衬料

This document describes the requirements for and methods of testing of organic linings which are applied to concrete process engineering equipment that will come in contact with aggressive chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners). The standard applies to linings which serve one or more of the following purposes:  to protect the component from damaging effects of aggressive substances;  to protect waters (e.g. ground water) from harmful substances;  to protect the charge from becoming contaminated by components released from the substrate material;  to achieve a particular surface quality. The different lining systems are: a) bonded linings; b) mechanically fixed linings; c) loose linings of sheeting material; d) loose linings of pre-formed pieces or lining units. Handling of aggressive or water pollutant materials is understood to include e) storage; f) filling; g) loading and unloading; h) manufacture; i) treatment; j) use.

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Linings on concrete components

EN 14879-5:2007 防易腐蚀媒介引起腐蚀的工业装置和设备的保护用有机涂覆层系统及衬套.第5部分:混凝土部件的衬套

This document describes the requirements for and methods of testing of organic linings which are applied to concrete process engineering equipment that will come in contact with aggressive chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners). The standard applies to linings which serve one or more of the following purposes:  to protect the component from damaging effects of aggressive substances;  to protect waters (e.g. ground water) from harmful substances;  to protect the charge from becoming contaminated by components released from the substrate material;  to achieve a particular surface quality. The different lining systems are: a) bonded linings; b) mechanically fixed linings; c) loose linings of sheeting material; d) loose linings of pre-formed pieces or lining units. Handling of aggressive or water pollutant materials is understood to include e) storage; f) filling; g) loading and unloading; h) manufacture; i) treatment; j) use.

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components

EN 14879-4:2007 防止工业装置和设备受侵入介质腐蚀的有机涂层系统和衬料.第4部分:金属构件衬料

This document describes the requirements for and methods of testing of organic linings which are applied to metallic process engineering equipment that will come in contact with chemical substances. The requirements specified here may be used for the purposes of quality control (e. g. as agreed between the contract partners1)). The standard applies to linings which serve one or more of the following purposes: to protect the component from adverse effects of aggressive substances; to protect waters (e. g. ground water) from harmful substances; to protect the charge from becoming contaminated by components released from the substrate material; to achieve a particular surface quality.This standard applies to vessels, apparatus, piping parts and other components for process plants made of metallic substrate materials which are in contact with media and are provided with a surface protection made of a) prefabricated, natural or synthetic rubber based sheeting (subsequently named rubber lining), to be applied in the workshop or on site; b) prefabricated, phenol formaldehyde or epoxy resin based sheeting (subsequently named duroplastic lining), to be applied in the workshop only; c) prefabricated, thermoplastic products (e. g. foils, sheeting, plates, pipes) (subsequently named thermoplastic lining), to be applied in the workshop or on site. The standard specifies the requirements, acceptance inspection, packaging, transport, storage and installation of organic linings for metallic materials. The tests described inThis standard are intended for verification of the suitability of sheeting used for linings and for acceptance inspection to be carried out on the products during or after application of the lining or as part of routine inspections to determine any changes effected in the lining during service.

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 4: Linings on metallic components

BS EN 13523-26:2006 卷状涂覆金属.试验方法.第26部分:耐水浓缩

This Part of EN 13523 specifies a procedure for evaluating the condensation resistance of an organic coating (coil coating) on a metallic substrate, by means of exposure in a humidity cabinet under controlled conditions.

Coil coated metals - Test methods - Part 26: Resistance to condensation of water

LST EN 14879-2-2007 保护工业设备和工厂免受侵蚀性介质腐蚀的有机涂层系统和衬里 第2部分：金属部件上的涂层

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 2: Coatings on metallic components

BS EN 13523-25:2007 卷状涂覆金属 试验方法 第25部分：耐湿性

Coil coated metals. Test methods. Resistance to humidit

BS EN 13523-25:2006 卷状涂覆金属.试验方法.第25部分:耐湿性

This Part of EN 13523 specifies a procedure for evaluating the humidity resistance of an organic coating (coil coating) on a metallic substrate, by means of exposure in a humidity cabinet under controlled conditions.

Coil coated metals - Test methods - Part 25: Resistance to humidity

BS EN 13523-26:2007 卷状涂覆金属 试验方法 第26部分：耐水浓缩

Coil coated metals. Test methods. Resistance to condensation of water

LST EN 14879-3-2007 保护工业设备和工厂免受侵蚀性介质腐蚀的有机涂层系统和衬里 第3部分：混凝土部件上的涂层

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 3: Coatings on concrete components