25.220.60 标准查询与下载

DIN EN 14879-6:2010 防止侵蚀物体腐蚀工业装置和设备用有机涂层系统和衬里.第6部分:带有瓦片和砌砖工的组合衬里.德文版本EN 14879-6-2009

This European Standard describes the requirements and tests for combined linings with tile and brick layers for protection of industrial apparatus and plants against corrosion caused by aggressive media.

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 6: Combined linings with tile and brick layers; German version EN 14879-6:2009

GSO EN 13523-1:2010 涂层金属卷 测试方法 第1部分：涂层厚度

This Part of EN 13523 specifies the procedures for determining the thickness of an organic coating on a metallic substrate, using electrical measuring devices. Two appropriate methods are given in this Part of EN 13523: a) thickness measurement on magnetic substrate, for example cold rolled steel and metallic coated steel; b) thickness measurement on non-magnetic substrate, for example aluminium and its alloys. The methods are applicable only to products with smooth and flat substrates but the coating itself may be textured. In that case, the average of a series of readings will represent an average of the thickness of the organic coating. The methods are not applicable for coating thicknesses less than 3 μm.

Coil coated metals - Test methods - Part 1: Coating thickness

DS/EN 14879-6:2010 保护工业设备和工厂免受侵蚀性介质腐蚀的有机涂层系统和衬里 第6部分：瓷砖和砖层的组合衬里

This European Standard describes the requirements for and methods of testing of combined systems with tile and brick layers which are applied to concrete or metallic process engineering equipment that will come in contact with chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners or having been given by national regulations )).The standard applies to systems which serve one or more of the following purposes:- to protect the component from adverse effects of aggressive substances;- to protect waters (e.g. ground water) against hazardous su

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 6: Combined linings with tile and brick layers

EN 13523-29:2010 卷材覆层金属的试验方法.第29部分:耐环境污染(粘污性和剥落)

This European Standard specifies a procedure for the comparative evaluation of resistance to soiling of an organic coating on a metallic substrate (coil coating) in an outdoor exposure environment, particularly the soiling defect known as "Tiger stripes".

Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt pick-up and striping)

EN 13523-10:2010 涂覆金属卷材的试验方法.第10部分:耐荧光紫外光线和水冷凝

This European Standard specifies the basic principles and procedure for determining the resistance of an organic coating on a metallic substrate (coil coating) to a combination of fluorescent UV radiation, and water condensation and temperature under controlled conditions. Due to varied conditions which occur during natural weathering and the extreme nature of accelerated testing, correlation between the two cannot be expected. Not all organic coatings will perform on an equal basis but a degree of correlation between the same generic type might be observed.

Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

EN 13523-21:2010 卷材覆层金属的试验方法.第21部分:户外暴露板的评价

This European Standard specifies the procedure for evaluating the behaviour of an organic coating on a metallic substrate during and after outdoor exposure. Panel design, preparation and the procedure for outdoor exposure are performed in accordance with EN 13523-19. After washing of the panel some dirt can remain on the panel.This remaining dirt can influence the accuracy and precision of readings of gloss and colour, performed on exposed panels, although carried out in accordance with the standards. Unlike other precise measurements, the objective of this European Standard is to report on trends in the corrosion and/or paint degradation behaviour of coil coated panels.

Coil coated metals - Test methods - Part 21: Evaluation of outdoor exposed panels

EN 13523-8:2010 卷材涂层金属的试验方法.第8部分:耐盐雾性

This European Standard specifies the procedures for determining the resistance to salt spray (fog) of an organic coating on a metallic substrate (coil coating). For steel neutral salt spray (fog) is usually used, and for aluminium acetic acid salt spray (fog).

Coil coated metals - Test methods - Part 8: Resistance to salt spray (fog)

EN 13523-22:2010 卷材覆层金属的试验方法.第22部分:色差.目视比对

This European Standard specifies the procedure for determining the difference in the colour of an organic coating on a metallic substrate by visual comparison against a standard using either diffuse natural daylight or artificial daylight in a standard booth. NOTE Results might differ between natural and artificial daylight. It might be that two colour specimens will match in daylight but not under another light source.This phenomenon is known as metamerism (see EN 13523-15). If metameric match is to be reported in objective terms, spectrophotometric measurements (using CIE Standard Illuminants D65 and A) should be made, in accordance with EN 13523-15. No statement is made about either the precision or the accuracy of this procedure since the results derived are neither in numerical form nor do they provide a pass/fail evaluation in objective terms. Therefore,This procedure should only be used where the use of colour measuring instruments is not recommendable (evaluation of colour matches, inspection of metallic colours, etc.). Although colour measuring instruments should be used where possible, in some cases a visual comparison can be useful (evaluation of colour matches, inspection of metallic colours, etc.). The standardization of such visual comparisons, by light sources, illuminating and viewing geometry and specimen size, provides for improved uniformity of results.This practice is essential for critical colour matching and is highly recommended for colour inspections.

Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison

BS EN 14879-6:2010 防侵略媒介引起腐蚀的工业装置和设备保护用有机涂覆系统及衬套 衬瓦和砌砖层结合的衬套

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media. Combined linings with tile and brick layers

BS EN 14879-6:2009 防侵略媒介引起腐蚀的工业装置和设备保护用有机涂覆系统及衬套.衬瓦和砌砖层结合的衬套

This European Standard describes the requirements for and methods of testing of combined systems with tile and brick layers which are applied to concrete or metallic process engineering equipment that will come in contact with chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e.g. as agreed between the contract partners or having been given by national regulations1)). The standard applies to systems which serve one or more of the following purposes: - to protect the component from adverse effects of aggressive substances; - to protect waters (e.g. ground water) against hazardous substances; - to protect the charge from becoming contaminated by components released from the substrate material; - to achieve a particular surface quality. The described combined systems can be used for concrete or metallic process engineering equipment that will come into contact with chemical substances. The combined system is a combination of: - a coating according to EN 14879-2 or EN 14879-3 with an additional layer of tiles or bricks embedded in cement mortar, resin based mortar and/or potassium silicate mortar as an adhesive bonding cement (referred to simply as cement in this standard); or - a lining according to EN 14879-4 or EN 14879-5 with an additional layer of tiles or bricks embedded in cement mortar, resin based mortar and/or potassium silicate mortar as an adhesive bonding cement (referred to simply as cement in this standard). For design and preparation of substrate, see EN 14879-1.

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Combined linings with tile and brick layers

BS EN 15773:2009 热镀锌钢板或粉镀锌钢制物品[双重系统]的粉末有机涂层的工业应用.规范、推荐规范和指南

This European Standard specifies the agreements to be made between the client, the galvanizer / sherardizer, the chemical suppliers and the applicators of the pre-treatment and the powder organic coating systems (if they are not one and the same). It also specifies the quality of the galvanized or sherardized articles to which the powder organic coatings are to be applied and for the pre-treatment and powder organic coatings intended for application to the galvanized or sherardized articles. This standard applies to the application of hot dip galvanized, sherardized and powder organic coatings by controlled industrial processes to articles consisting of or manufactured from steel. The standard applies to hot dip galvanized products, galvanized in accordance with EN ISO 1461 and EN 10240 or products sherardized in accordance with EN 13811, as well as parts of these products manufactured from continuously galvanized sheet and strip galvanized in accordance with EN 10326 or EN 10327, which, after the galvanizing and/or assembly, or sherardizing, will have a powder organic coating system applied. This standard also applies to products which have been hot dip galvanized or sherardized according to specific product standards to which powder organic systems are applied. This standard might also be useful when supplying other organic coating systems (excluding wet paint systems).

Industrial application of powder organic coatings to hot dip galvanized or sherardized steel articles [duplex systems] - Specifications, recommendations and guidelines

BS EN 13523-27:2009 卷材涂层金属.试验方法.耐湿敷性能(糊剂试验)

This part of EN 13523 specifies a procedure for evaluating the resistance of an organic coating on a metallic substrate (coil coating) to conditions of extreme humidity (acid, alkaline and/or neutral).

Coil coated metals - Test methods - Resistance to humid poultice (Cataplasm test)

LST EN 13523-27-2009 卷材涂层金属 测试方法 第27部分：耐潮湿膏药（巴布试验）

Coil coated metals - Test methods - Part 27: Resistance to humid poultice (Cataplasm test)

NF T37-001-27:2009 卷材覆层金属.测试方法.第27部分:耐湿泥罨剂(泥罨剂测试费)

Coil coated metals - Test methods - Part 27 : resistance to humid poultice (Cataplasm test).

DIN EN 13523-27:2009 线圈涂层金属.试验方法.第27部分:耐潮涂覆剂(巴布剂试验),英文版本DIN EN 13523-27-2009-10

This part of EN 13523 specifies a procedure for evaluating the resistance of an organic coating on a metallic substrate (coil coating) to conditions of extreme humidity (acid, alkaline and/or neutral).

Coil coated metals - Test methods - Part 27: Resistance to humid poultice (Cataplasm test); English version of DIN EN 13523-27:2009-10

DS/EN 15773:2009 粉末有机涂层在热浸镀锌或渗锌钢制品 [双相系统] 上的工业应用 规范、建议和指南

This European Standard specifies the agreements to be made between the client, the galvanizer / sherardizer, the chemical suppliers and the applicators of the pre-treatment and the powder organic coating systems (if they are not one and the same). It also specifies the quality of the galvanized or sherardized articles to which the powder organic coatings are to be applied and for the pre-treatment and powder organic coatings intended for application to the galvanized or sherardized articles.This standard applies to the application of hot dip galvanized, sherardized and powder organic coatings by controlled industrial processes to articles consisting of or m

Industrial application of powder organic coatings to hot dip galvanized or sherardized steel articles [duplex systems] - Specifications, recommendations and guidelines

EN 13523-27:2009 线圈涂层金属的试验方法.第27部分:耐潮涂覆剂(巴布剂试验)

This part of EN 13523 specifies a procedure for evaluating the resistance of an organic coating on a metallic substrate (coil coating) to conditions of extreme humidity (acid; alkaline and/or neutral).

Coil coated metals - Test methods - Part 27: Resistance to humid poultice (Cataplasm test)

EN 15773:2009 热镀锌和镀锌钢件的有机粉末涂料的工业应用(热浸镀锌.漆).规格,推荐办法和指南

This European Standard specifies the agreements to be made between the client, the galvanizer / sherardizer, the chemical suppliers and the applicators of the pre-treatment and the powder organic coating systems (if they are not one and the same). It also specifies the quality of the galvanized or sherardized articles to which the powder organic coatings are to be applied and for the pre-treatment and powder organic coatings intended for application to the galvanized or sherardized articles.This standard applies to the application of hot dip galvanized, sherardized and powder organic coatings by controlled industrial processes to articles consisting of or manufactured from steel. The standard applies to hot dip galvanized products, galvanized in accordance with EN ISO 1461 and EN 10240 or products sherardized in accordance with EN 13811, as well as parts of these products manufactured from continuously galvanized sheet and strip galvanized in accordance with EN 10326 or EN 10327, which, after the galvanizing and/or assembly, or sherardizing, will have a powder organic coating system applied.This standard also applies to products which have been hot dip galvanized or sherardized according to specific product standards to which powder organic systems are applied.This standard might also be useful when supplying other organic coating systems (excluding wet paint systems).

Industrial application of powder organic coatings to hot dip galvanized or sherardized steel articles [duplex systems] - Specifications, recommendations and guidelines

EN 14879-6:2009 防侵略媒介引起腐蚀的工业装置和设备保护用有机涂覆系统及衬套.第6部分:衬瓦和砌砖层结合的衬套

This European Standard describes the requirements for and methods of testing of combined systems with tile and brick layers which are applied to concrete or metallic process engineering equipment that will come in contact with chemical substances (liquids, solids and gases). The requirements specified here may be used for the purposes of quality control (e. g. as agreed between the contract partners or having been given by national regulations). The standard applies to systems which serve one or more of the following purposes: to protect the component from adverse effects of aggressive substances; to protect waters (e. g. ground water) against hazardous substances; to protect the charge from becoming contaminated by components released from the substrate material; to achieve a particular surface quality. The described combined systems can be used for concrete or metallic process engineering equipment that will come into contact with chemical substances. The combined system is a combination of: a coating according to EN 14879-2 or EN 14879-3 with an additional layer of tiles or bricks embedded in cement mortar, resin based mortar and/or potassium silicate mortar as an adhesive bonding cement (re- ferred to simply as cement inThis standard); or a lining according to EN 14879-4 or EN 14879-5 with an additional layer of tiles or bricks embedded in cement mortar, resin based mortar and/or potassium silicate mortar as an adhesive bonding cement (re- ferred to simply as cement inThis standard). For design and preparation of substrate, see EN 14879-1.

Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 6: Combined linings with tile and brick layers

ASTM D1474-98(2008) 有机涂层压痕硬度的标准试验方法

Standard Test Methods for Indentation Hardness of Organic Coatings