29.035.01 绝缘材料综合 标准查询与下载

T/CEEIA 438-2020 电气绝缘用耐电晕聚酰亚胺薄膜技术要求

本标准规定了电气绝缘用耐电晕聚酰亚胺薄膜的技术要求，试验方法，检验规则，标志、包装、运输与贮存等。 本标准适用于电机线圈绕包材料以及电磁线绝缘用耐电晕聚酰亚胺薄膜。

Technical Requirements of Electrical Insulating Corona Resistant Polyimide Films

T/CEEIA 437-2020 天然酯型绝缘油与结构材料相容性试验方法

本标准规定了天然酯型电气绝缘液与结构材料相容性试验方法。 本标准适用于液浸式电气设备内部结构材料与天然酯的相容性试验。

Standard Test Methods for Compatibility of Natural Ester Type Insulating Oil with Construction Material

T/CEEIA 436-2020 合成有机酯型绝缘油与结构材料相容性试验方法

本标准规定了合成有机酯型绝缘油（以下简称“合成酯”）与结构材料的相容性试验方法。 本标准适用于合成酯与结构材料的相容性试验，不作为材料/系统寿命评估的依据。

Test Method for Compatibility of Synthetic Organic Ester Type Insulating Oil and Construction Material

T/CEEIA 433-2020 不饱和聚酯团状模塑料螺旋流动性试验方法

本标准规定了不饱和聚酯团状模塑料螺旋流动性的试验方法。 本标准适用于不饱和聚酯团状模塑料。 本标准涉及不饱和聚酯团状模塑料在规定的温度、压力条件下的标准螺旋流动的传递模压成型。 此试验方法可以用于质量控制测试和接收规范。 不应该单独凭借这一方法来比较模塑料的成型性，因为它不可能做到和实际生产模具相同的工况。 没有相等的ISO标准。

Spiral flow test method of unsaturated polyester bulk moulding compound

T/CEEIA 435-2020 电气用快速固化纤维增强不饱和聚酯模塑料

本标准规定了电气用快速固化纤维增强不饱和聚酯模塑料的基本组成、性能要求、试验方法、检验规则、包装、标志、运输和贮存。 本标准适用于固化时间低于每mm厚20 s的电气用纤维增强不饱和聚酯模塑料。

Fiber reinforced unsaturated polyester fast curing moulding compound for electrical application

T/CEEIA 434-2020 电气用低温固化纤维增强不饱和聚酯模塑料

本标准规定了电气用低温固化纤维增强不饱和聚酯模塑料的基本组成、性能要求、试验方法、检验规则、包装、标志、运输和贮存。 本标准适用于固化温度在120 ℃～130 ℃范围内的电气用纤维增强不饱和聚酯模塑料。

Fiber reinforced unsaturated polyester low temperature curing moulding compound for electrical application

ASTM D3755-20 直接电压应力下固体电绝缘材料介质击穿电压和绝缘强度的标准测试方法

1.1 This test method covers the determination of dielectric breakdown voltage and dielectric strength of solid electrical insulating materials under direct-voltage stress. 1.2 Since some materials require special treatment, reference shall also be made to ASTM specifications or to the test method directly applicable to the material to be tested. See Test Method D149 for the determination of dielectric strength of electrical insulating materials at commercial power frequencies. 1.3 This test method is similar to IEC Publication 243-2. All procedures in this test method are included in IEC 243-2. Differences between this test method and IEC 243-2 are largely editorial. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precaution statements are given in Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials Under Direct-Voltage Stress

KS C IEC 60455-2-2:2019 用于电绝缘的无溶剂可聚合树脂化合物的规范 - 第2-2部分:测试方法 - 用于电气目的的涂料粉末的测试方法

Specification for solventless polymerisable resinous compounds used for electrical insulation — Part 2-2: Methods of test —Test methods for coating powders for electrical purposes

KS C IEC 60370-2019 浸渍用绝缘树脂和清漆耐热性试验程序电击穿法

Test procedure for thermal endurance of insulating resins and varnishes for impregnation purposes — Electric breakdown methods

KS C IEC 60370:2019 浸渍用绝缘树脂和清漆耐热性试验程序电击穿法

Test procedure for thermal endurance of insulating resins and varnishes for impregnation purposes — Electric breakdown methods

KS C IEC 61212-3-2-2019 绝缘材料 - 基于用于电气用途的热固性树脂的工业刚性圆形层压管和杆 - 第3部分:单个材料的规格 - 第2页:圆形层压成型管

Insulating materials — Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes —Part 3: Specifications for individual materials —Sheet 2: Round laminated

KS C IEC 61212-3-2:2019 绝缘材料 - 基于用于电气用途的热固性树脂的工业刚性圆形层压管和杆 - 第3部分:单个材料的规格 - 第2页:圆形层压成型管

Insulating materials — Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes —Part 3: Specifications for individual materials —Sheet 2: Round laminated

KS C IEC 60454-1:2019 电气用压敏胶带规范 - 第1部分:一般要求

Specifications for pressure-sensitive adhesive tapes for electrical purposes — Part 1: General requirements

KS C IEC 60455-2-2-2019 用于电绝缘的无溶剂可聚合树脂化合物的规范 - 第2-2部分:测试方法 - 用于电气目的的涂料粉末的测试方法

Specification for solventless polymerisable resinous compounds used for electrical insulation — Part 2-2: Methods of test —Test methods for coating powders for electrical purposes

KS C IEC 60454-1-2019 电气用压敏胶带规范 - 第1部分:一般要求

Specifications for pressure-sensitive adhesive tapes for electrical purposes — Part 1: General requirements

T/CEEIA 411-2019 纳米粒子改性聚酯亚胺浸渍树脂

本标准规定了纳米粒子改性聚酯亚胺浸渍树脂的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于变频电机及普通高压电机绝缘浸渍用的纳米粒子改性聚酯亚胺浸渍树脂。

Nano-particle modified polyester imine impregnating resin

ANSI/CAN/UL 1446:2020 绝缘材料系统 概述

1.1 These requirements cover test procedures to be used in the evaluation of Class 120 (E) or higher electrical insulation systems (EIS) for use in the United States, and Class 130(B) or higher EIS for use in Canada, where the thermal factor is the dominating aging factor. These requirements also cover the investigation of the substitution of non-electrical insulating materials (NIM) components of insulation in a previously evaluated insulation system and also the test procedures to be used in the evaluation of magnet wire coatings, magnet wires, and varnishes. 1.2 These requirements for the evaluation of an EIS do not establish thermal ratings for/or alter established thermal ratings for individual components. 1.3 These requirements do not cover insulation systems exposed to radiation or operating in oils, refrigerants, soaps, or other media that potentially degrade insulating materials. 1.4 When any performance aspect of an end-product requirement is not covered by this standard, the applicable standard shall be used. 1.5 These requirements do not cover electrical insulation systems where transient overvoltages or partial discharge are present. Such electrical insulation systems shall be evaluated to the appropriate standard for the application. Such standards include, but are not limited to the following: a) IEEE C57.12.60; b) IEC 60034-18-31; or c) IEEE 1776.

Systems of Insulating Materials – General

IEC TR 61244-4:2019 聚合物长期辐射老化的测定第4部分:辐射条件下不同温度和剂量率的影响

Determination of long-term radiation ageing in polymers - Part 4: Effects of different temperatures and dose rates under radiation conditions

ASTM D2132-19 电绝缘材料的防尘、防雾和耐腐蚀性的标准试验方法

1.1 This test method is intended to differentiate solid electrical insulating materials with respect to their resistance to the action of electric arcs produced by conduction through surface films of a specified contaminant containing moisture. Test Methods D2302 and D2303 are also useful to evaluate materials. 1.2 Units—The values stated in SI units are the standard. The inch-pound units in parentheses are for information only. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no equivalent ISO standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Materials

EN IEC 62677-3-103:2019 低压和中压热缩模制形状 第3部分：个别材料规范 表 103：用于中压应用的热缩聚烯烃导电模制形状

IEC 62677-3-103:2019 is applicable to heat shrinkable low and medium voltage moulded shapes, conductive, in a range of configurations suitable for environmental sealing, mechanical protection, strain relief for power cable terminations, joints and stop ends. These moulded shapes have been found suitable for use for temperatures between -40 ºC and 100 ºC. The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive compatibility and temperature performance is given in Annex A. The manufacturers/suppliers can be consulted for options. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application will need to be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. The tests specified are designed to control the quality of the moulded shapes but it is recognized that they are designed to be used in low and medium voltage cable accessories and as such electrical performance will be proven as part of the assembly. Examples of this are described in EN 50393, HD 629 and IEC 60502 (all parts). Keywords: heat shrinkable, polyolefin, conductive moulded shapes for medium voltage applications

Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 103: Heat-shrinkable, polyolefin, conductive moulded shapes for medium voltage applications