29.080.30 绝缘系统 标准查询与下载

IEC 60071-12:2022 绝缘配合 第12部分：LCC HVDC 换流站的应用指南

Insulation co-ordination - Part 12: Application guidelines for LCC HVDC converter stations

KS C IEC 62068-2022 电绝缘材料和系统 评估重复电压脉冲下电耐久性的通用方法

Electrical insulating materials and systems - General method of evaluation of electrical endurance under repetitive voltage impulses

KS C IEC 61858-1-2022 电气绝缘系统 对已建立的电气绝缘（EIS）修改的热评估 第1部分：绕线绕组EIS

Electrical insulation systems — Thermal evaluation of modifications to an established electrical insulation(EIS)— Part 1:Wire-wound winding EIS

UL 1097-2021 电气设备用双绝缘系统

UL Standard for Safety Double Insulation Systems for Use in Electrical Equipment (Sixth Edition; Reprint with revisions through and including April 26@ 2016)

DIN IEC/TR 63040:2021 关于电气间隙和爬电距离的指南，特别是对于等于或小于 2 毫米的距离 影响参数研究的测试结果（IEC TR 63040:2016 + COR1:2019）

This document describes test results of research on dimensioning of clearances and creepage distances, for spacing equal to or less than 2 mm for printed wiring material and other equivalent arrangements of insulation, where the clearance and the creepage distance follows the sam

Guidance on clearances and creepage distances in particular for distances equal to or less than 2 mm - Test results of research on influencing parameters (IEC TR 63040:2016 + COR1:2019)

GSO IEC TR 61857-2:2021 电气绝缘系统 热评估程序 第2部分：选择适当的测试方法来评估和分类电气绝缘系统

IEC TR 61857-2:2015(E) gives guidelines to identify the appropriate test method to be used for the evaluation of a proposed Electrical Insulation System (EIS). Some of the standards are for evaluation and classification of the EIS, while other standards identify the appropriate method to evaluate single or multi-factor stresses of a proposed or of an established EIS. This Technical Report is applicable to existing or proposed EIS used in electrotechnical products across a wide range of operating voltages of IEC Standards. The report takes care to select the appropriate standard based on construction and intended operating conditions.

Electrical insulation systems - Procedures for thermal evaluation - Part 2: Selection of the appropriate test method for evaluation and classification of electrical insulation systems

GSO IEC 61858-1:2021 电气绝缘系统 对已建立的电气绝缘系统 (EIS) 修改的热评估 第1部分：绕线绕组 EIS

IEC 61858-1:2014 lists the required test procedures for qualification of modifications of an established electrical insulation system (EIS) with respect to its thermal classification. This standard is applicable to EIS used in wire-wound winding electrotechnical devices. The test procedures are comparative in that the performance of a candidate EIS is compared to that of a reference EIS, which has proven service experience in accordance with IEC 60505 or has been evaluated by one of the procedures given in the IEC 61857 series. This first edition of IEC 61858-1 cancels and replaces the third edition of IEC 61858, published in 2008. It constitutes a technical and editorial revision. This edition includes the following significant technical changes with respect to the previous edition: a) this part is specifically for wire-wound winding EIS; b) new figures and charts support the contents.

Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 1: Wire-wound winding EIS

GSO IEC TS 62993:2021 额定电压超过 1 000 V AC 和 1 500 V DC 以及高达 2 000 V AC 和 3 000 V DC 的设备的电气间隙、爬电距离和固体绝缘要求的确定指南

IEC TS 62993:2017 gives guidance to technical committees which deal with equipment having a rated voltage of more than 1 000 V AC and up to 2 000 V AC, or a rated voltage of more than 1 500 V DC and up to 3 000 V DC. Rated voltages up to 1 000 V AC and 1 500 V DC, as well as higher or lower internal voltages, are covered by IEC 60664-1. This document applies to equipment for use up to 2 000 m above sea level, and provides guidance for use at higher altitudes. This document gives guidance for clearances, creepage distances and solid insulation for equipment to achieve safety. It includes methods of electric testing. The contents of the corrigendum of June 2018 have been included in this copy.

Guidance for determination of clearances, creepage distances and requirements for solid insulation for equipment with a rated voltage above 1 000 V AC and 1 500 V DC, and up to 2 000 V AC and 3 000 V DC

GSO IEC 61858-2:2021 电气绝缘系统 对已建立的电气绝缘系统 (EIS) 修改的热评估 第2部分：模绕 EIS

IEC 61858-2:2014 lists the required test procedures for qualification of modifications of an established electrical insulation system (EIS) with respect to its thermal classification. This standard is applicable to EIS used in form-wound electrotechnical devices. The test procedures are comparative in that the performance of a candidate EIS is compared to that of a reference EIS, which has proven service experience in accordance with IEC 60505 or has been evaluated by one of the procedures given in IEC 60085 and IEC 60034-18-31.

Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 2: Form-wound EIS

GSO IEC 61857-31:2021 电气绝缘系统 热评估程序 第31部分：设计寿命为 5 000 小时或更短的应用

IEC 61857-31:2017 establishes an EIS evaluation for applications with a designed life of 5 000 h or less. This test method follows the procedures of IEC 60505 and is modified based on the range of designed life.

Electrical insulation systems - Procedures for thermal evaluation - Part 31: Applications with a designed life of 5 000 h or less

GSO IEC TS 62332-2:2021 电气绝缘系统 (EIS) 液体和固体成分组合的热评估 第2部分：简化测试

IEC TS 62332-2:2014 is applicable to EIS containing solid and liquid components where the thermal stress is the dominant ageing factor, without restriction to voltage class. This part specifies a sealed tube test procedure for the thermal evaluation and qualification of electrical insulation systems (EIS). One aspect of this procedure is to also provide a method to assign thermal classifications to materials used in EIS where solid and liquid components are both used. This procedure describes a comparative ageing method whereby a reference system composed of kraft paper and mineral oil is compared to a candidate system of any combination of solid and insulating liquid. The test procedures in this part are specifically applicable to liquid immersed transformer insulation systems.

Electrical insulation systems (EIS) - Thermal evaluation of combined liquid and solid components - Part 2: Simplified test

GSO IEC 62068:2021 电绝缘材料和系统 评估重复电压脉冲下电耐久性的通用方法

IEC 62068:2013 applies to electrical equipment, regardless of voltage, containing an insulation system, which is: - connected to an electronic power supply, and - requires an evaluation of insulation endurance under repetitive voltage impulses. This standard proposes a general test procedure to facilitate screening of electrical insulating materials (EIM) and systems (EIS) and to achieve a relative evaluation of insulation endurance under conditions of repetitive impulses. This first edition of IEC 62068 replaces IEC 62068-1:2003. It has been re-numbered as IEC 62068, as decided at the Plenary Meeting of TC 112 in Prague 2011. The main changes with regard to IEC 62068-1:2003 concern the terms and definitions which are now aligned, in part, on IEC/TS 61934 and IEC/TS 60034-18-42.

Electrical insulating materials and systems - General method of evaluation of electrical endurance under repetitive voltage impulses

GSO IEC TR 63040:2021 电气间隙和爬电距离指南 特别是等于或小于 2 mm 的距离 影响参数研究的测试结果

IEC TR 63040:2016(E) describes test results of research on dimensioning of clearances and creepage distances, for spacing equal to or less than 2 mm for printed wiring material and other equivalent arrangements of insulation, where the clearance and the creepage distance follows the same path along the surface of solid insulation. The information contained in this document is the result of research only and cannot be used for dimensioning the clearances and creepage distances for equipment within low-voltage systems, where IEC 60664-1 applies. However distances can be taken into account for functional reasons. This document provides results of research related to the following criteria: 1) clearances independent from the micro-environment; 2) creepage distances for pollution degree 1, 2 and 3 which extends the use of smaller distances to products having design features similar to printed circuit boards; 3) creepage distances to avoid flashover of the insulating surface; 4) information on minimum creepage distances to maintain minimum insulation resistance. A test method for the evaluation of the relevant water adsorption group for the surface of any insulating material which has not yet been classified is described. The contents of the corrigendum of January 2019 have been included in this copy.

Guidance on clearances and creepage distances in particular for distances equal to or less than 2 mm - Test results of research on influencing parameters

OVE EN IEC 61857-32:2021 电气绝缘系统 热评估程序 第32部分：诊断测试期间增加因素的多因素评估（（IEC 61857-32:2019）EN IEC 61857-32:2019）（德文版）

Electrical insulation systems - Procedures for thermal evaluation - Part 32: Multifactor evaluation with increased factors during diagnostic testing ((IEC 61857-32:2019) EN IEC 61857-32:2019) (german version)

PN-EN 60034-18-42-2017-09/A1-2021-05 E 旋转电机 第 18-42 部分：用于由电压转换器供电的旋转电机的抗局部放电电气绝缘系统（II 型） 资格测试

Rotating electrical machines - Part 18-42: Partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters - Qualification tests

PN-EN 60034-18-41-2014-10/AC-2021-05 E 旋转电机 第 18-41 部分：用于由电压转换器供电的旋转电机的无局部放电电气绝缘系统（I 型） 鉴定和质量控制测试

Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in electrical rotating machines fed from voltage converters - Qualification and quality control tests

DIN EN 60034-18-41:2021 旋转电机. 第18-41部分: 由电压转换器供电的旋转电机中使用的无局部放电电气绝缘系统(I 型). 资格和质量控制试验(IEC 60034-18-41-2014 + A1-2019 + COR1: 2020); 德文版 EN 60034-18-41-2014 + A1-2019 + AC-2020

The existing Text has been replaced in some clauses by a new text of amendment 1. In detail, the terms have been supplemented and the requirements for routine testing have been revised.

Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests (IEC 60034-18-41:2014 + A1:2019 + COR1:2020

DIN EN IEC 61857-32:2021 电气绝缘系统. 热评估程序. 第32部分: 诊断试验期间增加因素的多因素评估(IEC 61857-32-2019); 德文版 EN IEC 61857-32-2019

Is focused on applications where other possible factors need to be incorporated to evaluate any influence on the performance of the EIS. Multi-factor evaluation is the most complex type of project to design and conduct. Clear guidelines are needed to give the user of this standar

Electrical insulation systems - Procedures for thermal evaluation - Part 32: Multifactor evaluation with increased factors during diagnostic testing (IEC 61857-32:2019); German version EN IEC 61857-32:2019

PN-EN IEC 60664-1-2021-02/AC-2021-04 E 低压供电系统内设备的绝缘配合 第1部分：原理、要求和试验（IEC 60664-1:2020/COR1:2020）

Insulation coordination for equipment within low-voltage supply systems--Part 1: Principles, requirements and tests (IEC 60664-1:2020/COR1:2020)

PN-EN IEC 60664-1-2021-02 E 低压供电系统内设备的绝缘协调 第1部分：原则、要求和测试（IEC 60664-1:2020）

Insulation coordination for equipment within low-voltage supply systems - Part 1: Principles, requirements and tests (IEC 60664-1:2020)