29.140.40 照明设备 标准查询与下载

T/ZALI 0015-2024 普通照明用LED平板灯技术规范

本文件规定了普通照明用LED平板灯的术语和定义、要求、试验方法、标志、包装、运输和贮存。 本文件适用于以LED为光源，额定电压220 V，频率为50 Hz，厚度不超过85 mm的普通照明用室内LED平板灯。 本文件不适用于发光面上带有彩色、图案或装饰件等的LED平板灯。

Technical Specifications for LED Flat Panel Lamps for General Lighting

T/CASME 1376-2024 LED智慧路灯

本文件规定了LED智慧路灯的技术要求、试验方法、检验规则、标志、包装、运输和贮存。

LED smart street light

T/QGCML 3274-2024 强散热性太阳能路灯

本文件规定了强散热性太阳能路灯的产品结构、要求、试验方法、检验规则、标志、说明书、包装、运输和贮存。 本文件适用于强散热性太阳能路灯的生产和检验。

Strong heat dissipation solar street light

T/JSIES 009-2024 生鲜食用农产品销售用照明灯具

1 范围 2 规范性引用文件 3 术语和定义 4 分类 5 要求 5.1 一般要求 5.2 技术要求 6 试验方法 6.1 色度试验方法 6.2 防护等级试验方法 6.3 灯具能效试验方法 6.4 光通维持率试验方法 6.5 标记试验方法

Lighting luminaire for the sale of fresh edible agricultural products

T/CZGJ 001-2024 智能型升降灯具

1  范   围　 2  规范性引用文件　 3  术语与定义　 4  产品型号　 5  系统组成与工作原理　 6  结构与功能　 7  技术要求　 8  试验方法　 9  检验规则　 10  标   志　 11  运输与贮存　

Intelligent lifting luminaires

GSO IEC 62722-1:2024 灯具性能 第1部分：一般要求

IEC 62722-1:2022 is available as IEC 62722-1:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 62722-1:2022 covers specific performance and environmental requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V. Unless otherwise detailed, performance data covered under the scope of this document are for the luminaires in a condition representative of new manufacture, with any specified initial aging procedures completed. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - The reference to and use of the measurement methods for non-active power consumption in accordance with IEC 63103 have been added. - The pictograms of Annex C have been updated to represent modern light sources.

Luminaire performance - Part 1: General requirements

GSO IEC 60598-2-18:2024 灯具 第2-18部分：特殊要求 游泳池和类似应用的灯具

IEC 60598-2-18:2022 specifies requirements for fixed luminaires intended for use in water, or in contact with water, in, for example, the basins of swimming pools, fountains, paddling pools, and garden pools, and for use with electric light sources. This third edition cancels and replaces the second edition published in 1993 and Amendment 1:2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: references to Part 1 have been updated; some subclauses have been renumbered; the standard has been redrafted such that it is applicable to both filament lamps and LED light sources; marking requirements have been updated and 18.5.3 of the previoius edition has been deleted; 18.10.3 of the previous edition has been deleted, as it is no longer relevant, following the update of requirements for cross-sectional areas of external and internal cables in Section 5 of Part 1; 18.10.4 and 18.10.5 of the previous edition renumbered as 18.11.4 and 18.11.5 in this edition have been adapted to allow the use of an alternative waterproof multi-core cable that conforms to the waterproof test of Annex D and Annex E of EN 50525‑2‑21:2011 or to an equivalent regional standard; in 18.11 (18.10 in the previous edition), the cross-sectional area of wiring has been aligned with Part 1; in 18.11 (18.10 in the previous edition), the types of cables have been updated with alternative regional cables.

Luminaires - Part 2-18: Particular requirements - Luminaires for swimming pools and similar applications

GSO IEC 62722-2-1:2024 灯具性能 第2-1部分：特殊要求 LED 灯具

IEC 62722-2-1:2023 specifies the performance requirements for LED luminaires, together with the test methods and conditions. It applies to LED luminaires for general lighting purposes. Semi-luminaires are not covered under the scope of this document. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: alignment with IEC 62717:2014, IEC 62717:2014/AMD1:2015 and IEC 62717:2014/AMD2:2019; clarification of temperature requirements for the maintenance test, in 10.2 and Annex A; introduction of a new Annex C on methods for calculation and measurements of parameters for extension of electric and photometric data.

Luminaire performance - Part 2-1: Particular requirements - LED luminaires

GSO IEC 60598-2-22:2024 灯具 第2-22部分：特殊要求 应急照明灯具

IEC 60598-2-22:2021 is available as IEC 60598-2-22:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60598-2-22:2021 specifies requirements for emergency luminaires for use with electrical lamps on emergency power supplies not exceeding 1 000 V. This fifth edition cancels and replaces the fourth edition published in 2014 and Amendment 1:2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - update of requirements for rest mode and inhibiting mode; - clarification of high temperature operation tests; - introduction of new requirements for lithium batteries; - introduction of new requirements for electric double layer capacitors (EDLCs); - clarification of resistance to heat, fire and tracking; - clarification of test facilities for self-contained luminaires; - clarification of the test method for contrast measurements of exit signs.

Luminaires - Part 2-22: Particular requirements - Luminaires for emergency lighting

GSO IEC 60598-2-1:2024 灯具 第2-1部分：特殊要求 固定通用灯具

IEC 60598-2-1:2020 specifies requirements for fixed general purpose luminaires for use with electric light sources on supply voltages not exceeding 1 000 V. This second edition cancels and replaces the first edition published in 1979 and Amendment 1:1987. This edition constitutes a technical revision. This edition includes the following technical changes with respect to the previous edition (there are no major technical changes, see Annex A): a) the scope has been modified to be in line with Part 1 to include all electric light sources, b) references to Part 1 have been updated.

Luminaires - Part 2-1: Particular requirements - Fixed general purpose luminaires

GSO IEC 60598-2-20:2024 灯具 第2-20部分：特殊要求 灯链

IEC 60598-2-20:2022 is available as IEC 60598-2-20:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60598-2-20:2022 specifies requirements for lighting chains fitted with series, parallel or a combination of series/parallel connected light sources for use either indoors or outdoors on supply voltages not exceeding 250 V. This fifth edition cancels and replaces the fourth edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - specific provisions for temporarily installed protected lighting (TPL) chains have been added; - new terms and definitions have been added.

Luminaires - Part 2-20: Particular requirements - Lighting chains

GSO IEC 60598-2-14:2024 灯具 第2-14部分：特殊要求 冷阴极管状放电灯（氖管）和类似设备的灯具

IEC 60598-2-14:2009 applies to luminaires for cold cathode tubular discharge lamps and similar equipment, operating on a no-load rated output voltage over 1 000 V but not exceeding 10 000 V, mainly used for general lighting, for indoor or outdoor applications and for supply voltages up to 1 000 V. This publication is intended to be read in conjunction with IEC 60598-1: Luminaires - Part 1: General requirements and tests. It was established on the basis of the seventh edition (2008) of that standard. This publication is intended to be read in conjunction with IEC 60598-1:2008.

Luminaires - Part 2-14: Particular requirements - Luminaires for cold cathode tubular discharge lamps (neon tubes) and similar equipment

T/HBEEIA 001-2024 中小学教室照明技术规范

本文件的主要内容包括以下方面： 1 LED 灯具技术要求 a） 灯具安全要求，应通过国家强制性产品认证，且灯具的 IP 等级满足 IP 40 或以上等级要求，此外还应满足电磁兼容、噪声、有毒有害物质限量、视网膜蓝光危害等级等要求； b） 灯具性能要求，应满足灯具能效、颜色特性、功率因数、波动深度、短期闪烁值、频闪效应可视度、寿命等参数要求； c） 在 VDT 条件下使用的灯具，也应进行 VDT 环境亮度限制； 2 教室照明质量要求 a） 教室的照明应满足视觉需求照明、舒适性等共计 10 项技术要求。包括视觉需求照明相关的教室桌面照度、书写板面照度、统一眩光值、相关色温、显色指数和教室照明功率密度 6 项技术要求，舒适性照明相关的空间明亮指数、空间明亮度对比度 2 项技术要求，以及视黑素等效勒克斯（或生理等效照度）和现场蓝光危险等级 2 项技术指标； b） 教室设置板书模式、多媒体模式、自习模式、课间模式等不同照明场景模式时，每种照明场景模式都应满足不同的光环境技术要求； c） 设置智能控制的教室照明系统，宜符合 GB/T 39021—2020 的规定； d） 应保持作业面规定的维持平均照度，采取以下维护措施： 1） 应定期维护和更新损坏、有缺陷的灯具； 2） 应每学期清洁照明装置表面； 3） 当灯具因光衰不能满足要求时，应更换灯具。 3 光环境测试方法 规定了教室光环境中各参数的测试方法.

Technical specification for classroom lighting in primary and middle schools

T/GIES 020-2024 质量分级及“领跑者”评价要求 LED立式读写灯具

基础指标：符合安全要求、谐波电流、无线电骚扰特性、限用物质的限量要求、蓝光危害、遮光性、噪声、波动深度、15°倾倒的相关要求。 核心指标：照度及照度均匀度、一般显色指数、光效、额定寿命、眩光等划分为不同水平。 创新性指标：特殊显色指数、平面色品差异、CQS（光色品质）。

Assessment requirements for quality grading and forerunner — LED vertical luminaires for paper task

T/JSQA 174-2023 钢质照明灯杆

基本要求：材料及配套件、设计要求、生产工艺要求； 技术要求：尺寸及公差（标称高度、壁厚、悬臂悬伸长度、灯具安装角、灯具连接件尺寸、检修门、埋地深度、底板、法兰板、钢制灯杆横截面尺寸公差、直线度、垂直度公差）、结构要求、接地端子、检修门耐冲击性能、灯杆耐冲击性能、外壳防护等级、负载要求、焊接性能、耐腐蚀性能。

Steel lighting pole

T/QGCML 2916-2023 照度自适应感应调节的LED面板灯设计规范

本文件规定了照度自适应感应调节的LED面板灯设计的结构与型号、设计要求、证实方法、设计文件。 本文件适用于照度自适应感应调节的LED面板灯（以下简称“面板灯”）的设计。

Design specifications for LED panel lights with adaptive illumination induction adjustment

T/CEEIA 730-2023 LED灯具透雾性能效测试方法

本文件规定了户外LED照明灯具在不同浓度等级雾环境中的透雾率和能效测试要求，确立了测试设施架设要求，描述了测试方法要求。 本文件适用于户外定向照明LED灯具。

Test method for fog permeability energy efficiency of LED luminaire

T/QGCML 2871-2023 户外手持式LED移动照明灯具

本文件规定了户外手持式LED移动照明灯具的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以LED为光源的户外手持式可移动照明灯具（以下简称“灯具”）。

Outdoor handheld LED mobile lighting fixtures

T/GIES 014-2023 渔船LED水上集鱼灯具装置技术要求

本文件规定了渔船LED水上集鱼灯具装置的技术要求和试验方法等。 本文件适用于输入电压不超过1000V，频率为50Hz或60Hz的渔船LED水上集鱼灯具装置，可作为该类装置研制、生产和检验的依据，也可作为应用选型的依据。

Technical specification for overwater LED fish gathering luminaires on fishing vessels

CSA C22.2 No.250.4-2023 便携式灯具

1 Scope 1.1 This Standard applies to portable luminaires, intended for use in dry, damp, and wet locations, and intended to be used in accordance with the Rules of CSA C22.1, Canadian Electrical Code, Part I, in non- hazardous locations, on a nominal 120 V system and 15 or 20 A branch circuits, or on the load side of a Class 2, LED Class 2, or safety extra-low voltage (SELV) circuit. 1.2 This Standard applies to portable, incandescent, fluorescent, HID, LED, and other lighting technology luminaires for illuminative or decorative purposes and combinations of these, such as a) amateur movie lights; b) aquarium; c) cabinet (including under-cabinet); d) clamp type; e) chain-and-hook-supported types (including flexible-cord-, steel-cable- or rope-supported); f) colour wheels; g) display case type; h) drafting type; i) electronic (flashing, touch-control) types; j) extension handlamps; k) extra low voltage portable luminaires, supplied from a remote power source; l) fibre-optic types; m) flood lights; n) floor type; o) counterfeit detectors; p) hobby type; q) hospital type; r) illuminated forms or shapes (figurines, fire logs, terrestrial globes, plaques, etc.); s) kits, portable luminaires; t) machine-shop lamps (e.g., illuminated shields for use with electric grinders); u) make-up mirrors; v) office furnishing luminaires; w) picture lights; x) planter lights; y) paint curing types; z) table type; aa) wall (pin-ups); ab) work lamps; and ac) 1.3 This Standard does not apply to luminaires covered by other applicable standards, such as a) decorative lighting products; b) emergency lighting equipment; c) stage and studio luminaires; d) electric signs and displays; e) radiant heaters and infrared and ultraviolet lamp assemblies for cosmetic or hygienic; f) purposes in non-medical applications; g) low voltage landscape lighting systems; h) submersible lighting systems; i) direct plug-in nightlights; j) flashlights and lanterns; and k) horticultural lighting equipment and systems. 1.4 For the purpose of this Standard, the term “luminaire” means portable luminaire. 1.5 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.6 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. battery-operated luminaires intended to operate unattended while disconnected from an external power source.

Portable luminaires