29.140.40 照明设备 标准查询与下载

T/GIES 006-2023 幼儿园及幼教场所室内照明技术规范

本团体标准对幼儿园及幼教场所室内照明灯具的安全、性能及现场测试等方面进行了详细规定，为幼儿园及幼教场所的光环境要求提供质量评价依据。

Technical specification for indoor lighting in kindergartens and nursery school

T/CASME 431-2023 多功能智能夜灯

本文件规定了多功能智能夜灯的要求、试验方法、检验规则、标志、包装、运输和贮存。

Multifunctional intelligent night light

CSA E60598-2-5-2023 灯具 第2-5部分：特殊要求 泛光灯

Scope This part of the CSA E60598 series of Standards specifies requirements for floodlights designed to be installed on branch circuits not exceeding 600 V nominal or less between conductors in accordance with CSA C22.1, Canadian Electrical Code, Part I. It is to be read in conjunction with those clauses of CSA E60598-1 to which reference is made.

Luminaires — Part 2-5: Particular requirements — Floodlights

CSA E60598-1-2023 灯具 第1部分：一般要求和测试 灯具 第1部分：一般要求和测试

This Part 1 of IEC 60598 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V. The requirements and related tests of this document cover: classification, marking, mechanical construction, electrical construction and photobiological safety. Each section of this Part 1 is read in conjunction with this Section 0 and with other relevant sections to which reference is made. Each part of IEC 60598-2 details requirements for a particular type of luminaire or group of luminaires on supply voltages not exceeding 1 000 V. These parts are published separately for ease of revision and additional sections will be added as and when a need for them is recognized. The presentation of photometric data for luminaires is under consideration by the International Commission on Illumination (CIE) and is not, therefore, included in this Part 1. Requirements are included in this Part 1 for luminaires incorporating ignitors with nominal peak values of the voltage pulse not exceeding those of Table 11.2. The requirements apply to luminaires with ignitors built into ballasts and to luminaires with ignitors separate from ballasts. For luminaires with ignitors built into lamps, the requirements are under consideration. Requirements for semi-luminaires are covered in a separate Standard. In general, this Part 1 covers safety requirements for luminaires. The object of this Part 1 is to provide a set of requirements and tests which are considered to be generally applicable to most types of luminaires and which can be called up as required by the detail specifications of IEC 60598-2. This Part 1 is thus not regarded as a specification in itself for any type of luminaire, and its provisions apply only to particular types of luminaires to the extent determined by the appropriate part of IEC 60598-2. The parts of IEC 60598-2, in making reference to any of the sections of Part 1, specify the extent to which that section is applicable and the order in which the tests are performed; they also include additional requirements as necessary. The order in which the sections of Part 1 are numbered has no particular significance as the order in which their provisions apply is determined for each type of luminaire or group of luminaires by the appropriate part of IEC 60598-2. All parts of IEC 60598-2 are self-contained and therefore do not contain references to other parts of IEC 60598-2. Where the requirements of any of the sections of Part 1 are referred to in the parts of IEC 60598-2 by the phrase "The requirements of section... of IEC 60598-1 apply", this phrase is interpreted as meaning that all the requirements of that section of Part 1 apply except those which are clearly inapplicable to the particular type of luminaire covered by that part of IEC 60598-2. For explosion proof luminaires, as covered by IEC 60079, the requirements of IEC 60598 (selecting the appropriate parts 2) are applied in addition to the requirements of IEC 60079. In the event of any conflict between IEC 60598 and IEC 60079, the requirements of IEC 60079 take priority. Improvements in safety to take into account the state of the art technology are incorporated in the standards with revisions and amendments on an ongoing basis. Regional standardization bodies can include statements in their derived standards to cover products which have complied with the previous document as shown by the manufacturer or standardization body. The statements may require that for such products, the previous standard may continue to apply to production until a defined date after which the new standard shall apply. This Standard applies to the safety of such equipment designed to be installed on branch circuits not exceeding 600 V nominal or less between conductors in accordance with CSA C22.1, Canadian Electrical Code, Part I.

Luminaires — Part 1: General requirements and tests Luminaires — Partie 1 : Exigences générales et essais

CSA E60598-2-1-2023 灯具 第2-1部分：特殊要求 固定式通用灯具 灯具 第2-1部分：特殊要求 固定式通用灯具

Scope This part of the CSA E60598 series of Standards specifies requirements for fixed general-purpose luminaires for use with electric light sources designed to be installed on branch circuits not exceeding 600 V nominal or less between conductors in accordance with CSA C22.1, Canadian Electrical Code, Part I. It is to be read in conjunction with those clauses of CSA E60598-1 to which reference is made.

Luminaires — Part 2-1: Particular requirements — Fixed general purpose luminaires Luminaires — Partie 2-1 : Exigences particulières — Luminaires fixes à usage général

T/CASME 407-2023 舞台灯光智能控制管理系统通用技术要求

本文件规定了舞台灯光智能控制管理系统的产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

General technical requirements for stage lighting intelligent control and management system

T/CZZMXH 003-2023 LED 工厂灯

本文件规定了LED工厂灯的定义、产品分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存要求。

LED factory lamp

T/CASME 383-2023 无人机无线充电智慧灯杆

本文件规定了无人机无线充电智慧灯杆的术语和定义、产品结构、技术要求、试验方法、检验规则、标志、包装、运输、贮存。

UAV wireless charging smart light pole

T/CI 056-2023 LED储能道路灯具

5　技术要求 外观 灯具表面应光滑，涂层色泽应均匀一致，无流挂、堆积、露底等影响外观的缺陷，灯体内外应无危及安全的尖角和毛刺，紧固件连接应牢固。 电源管理 5.2.1　充电电压控制 在正常工作条件及故障条件下均不应造成对电池或电池组的过压充电。 5.2.2　充电电流控制 在正常工作条件及故障条件下均不应造成对电池或电池组的过流充电。 5.2.3　放电电流控制 在正常工作条件及故障条件下均不应造成对电池或电池组的过流放电。 5.2.4　充放电温度控制 当温度超出60℃的要求时，电池应不能进行充放电。充放电行为停止时，温度值不应超过60℃。 电池组保护 5.3.1　过压充电保护 在过压充电时，充电电流为1C充电电流，充电电压为(n×3.6)V，试验后，电池保护装置应启动保护，且应不爆炸、不起火、不漏液。 5.3.2　过流充电保护 在过流充电时，充电电流为l.5倍的过流充电保护电流，试验后，电池保护装置应启动保护，且应不爆炸、不起火、不漏液。 5.3.3　欠压放电保护 在欠压放电时，单个电池最低电压为2.5V，试验后，电池保护装置应启动保护，且应不爆炸、不起火、不漏液。 5.3.4　过流放电保护 在过流放电时，放电电流为l.5倍的过流放电保护电流，试验后，电池保护装置应启动保护，且应不爆炸、不起火、不漏液。 5.3.5　短路保护 在短路时，外部短路总电阻为80 mΩ±20 mΩ，试验后，电池保护装置应启动保护，且应不爆炸、不起火、不漏液。

LED energy storage road lighting

DB65/T 4622-2022 中小学校教室照明技术规范

Technical specifications for classroom lighting in primary and secondary schools

DB4404/T 43-2023 市政照明设施管养质量要求

本文件适用于珠海市城市规划区内的市政照明设施的养护和管理。

Quality requirements for management and maintenance of municipal lighting facilities

T/FSS 25-2023 佛山标准 LED路灯

本文件规定了LED路灯的术语和定义、要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于道路和街道照明用LED灯具。

Foshan standard LED luminaires for road lighting

BS EN IEC 62722-2-1:2023 表演照明 特殊要求 LED灯具

1   Scope This part of IEC 62722 specifies the performance requirements for LED luminaires , together with the test methods and conditions. It applies to LED luminaires for general lighting purposes. Semi-luminaires are not covered under the scope of this document. For some types of luminaires (e.g. decorative or household) the provision of performance data under the scope of this document is not appropriate. In this document, the following types of LED luminaires are distinguished. – Type A – Luminaires using LED modules where compliance with IEC 62717 is given. – Type B – Luminaires using LED modules where compliance with IEC 62717 is not given. Luminaires using an LED lamp are covered in IEC 62722‑1 and are not within the scope of this document. The requirements of this document relate to type testing. This document covers LED luminaires using LED modules, based on inorganic LED technology that produces white light. It does not cover luminaires using light sources based on OLED technology (organic LED technology). The lifetime of LED luminaires is in most cases much longer than the practical test times. Consequently, the verification of manufacturer’s lifetime claims is out of the scope of this document.

Luminaire performance. Particular requirements. LED luminaires

23/30451017 DC BS EN IEC 60598-1 AMD 1. 灯具 第 1 部分：一般要求和测试

BS EN IEC 60598-1 AMD 1. Luminaires - Part 1. General requirements and tests

EN IEC 62722-2-1:2023 灯具性能 第 2-1 部分：特殊要求 LED 灯具

IEC 62722-2-1:2023 specifies the performance requirements for LED luminaires, together with the test methods and conditions. It applies to LED luminaires for general lighting purposes. Semi-luminaires are not covered under the scope of this document. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: alignment with IEC 62717:2014, IEC 62717:2014/AMD1:2015 and IEC 62717:2014/AMD2:2019; clarification of temperature requirements for the maintenance test, in 10.2 and Annex A; introduction of a new Annex C on methods for calculation and measurements of parameters for extension of electric and photometric data.

Luminaire performance - Part 2-1: Particular requirements - LED luminaires

T/CASMES 147-2023 装饰照明用LED霓虹灯

本文件规定了装饰照明用LED霓虹灯的要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于电源电压不超过DC 48V的装饰照明用LED霓虹灯。

LED neon lights for decorative lighting

T/STIC 110085-2023 LED数字化照明投光灯具

本标准规定了LED数字化照明投光灯具产品的范围、术语和定义，规格、要求、试验方法、检验规则、标志、包装、运输和储存。 本文件适用于LED数字化照明投光灯具的设计、生产、检验与验收。

LED Digital Lighting Floodlight

IEC 62722-2-1:2023 CMV 灯具性能.第2-1部分:特殊要求.LED灯具

Luminaire performance - Part 2-1: Particular requirements - LED luminaires

IEC 62722-2-1:2023 灯具性能.第2-1部分:特殊要求.LED灯具

Luminaire performance - Part 2-1: Particular requirements - LED luminaires

T/CASME 171-2022 黑板照明LED灯具

本文件规定了黑板照明LED灯具的一般要求、技术要求、试验方法、检验规则、包装、运输和贮存。

Blackboard lighting LED lamp