31.220.10 插头和插座装置、连接器 标准查询与下载

GSO IEC 60512-6-2:2015 电子设备连接 测试和测量 零件编号 (6-2)：动态应力测试 测试 6B：冲击

1.1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to withstand specified severities of bump.

Connectors for electronic equipment - Tests and measurements - Part 6-2: Dynamic stress tests - Test 6b: Bump

GSO IEC 60512-12-3:2015 电子设备连接器 测试和测量 第12-3部分：焊接测试 测试 12c：可焊性、去湿性

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to define a standard test method to assess the ability of the terminations of a connector to remain covered with solder when being brought into contact with molten solder under specified conditions.

Connectors for electronic equipment - Tests and measurements - Part 12-3: Soldering tests - Test 12c: Solderability, de-wetting

GSO IEC 60130-17:2015 频率低于 3 MHz 的连接器 第17部分：允许多向配合的互连设备的详细规范 用于可充电电池

This part of IEC 60130 is a connector detail specification for a battery interconnection system for portable computers, cellular telephones and other electronic devices requiring power not to exceed 50 V d.c. SELV (Safety Extra Low Voltage).

Connectors for frequencies below 3 MHz - Part 17: Detailspecification for interconnection devices which permit multi-directional mating, for use with rechargeable batteries

GSO IEC 60512-6-1:2015 电子设备连接 测试和测量 零件编号 (6-1)：动态应力测试 测试 6a：加速 稳态

1.1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to withstand specified severities of acceleration.

Connectors for electronic equipment - Tests and measurements - Part 6-1: Dynamic stress tests - Test 6a: Acceleration, steady state

GSO IEC 60512-16-11:2015 电子设备的连接 测试和测量 第16-11部分：触点和端子的机械测试 测试 16k：无焊护套连接的断裂强度

This part of IEC 60512, when required by the detail specification, is used for testing electomechanical components within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to determine ability of a component to resist forces that might strip a wrapped connection from its post along the axis of the post. Such wrapped connections are described in IEC 60352-1. NOTE This test is considered as destructive to specimens used.

Connectors for electronic equipment - Tests and measurements - Part 16-11: Mechanical tests on contacts and terminations - Test 16k: Stripping force, solderless wrapped connections

GSO IEC 60512-11-3:2015 电子设备连接 测试和测量 第11-3部分：气候测试 测试 11c：湿热 稳定状态

1.1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to be stored and/or to function in a specified manner under conditions of high relative humidity.

Connectors for electronic equipment - Tests and measurements - Part 11-3: Climatic tests - Test 11c: Damp heat, steady state

GSO IEC 60512-15-1:2015 电子设备连接器 测试和测量 第15-1部分：连接器测试（机械） 测试 15a：插入件中的触点保持力

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this document is to detail a standard test method to assess the effectiveness of the contact retaining system to withstand axial loads likely to be encountered during normal use. The contact retaining system may retain the contact in an insert or directly into a housing.

Connectors for electronic equipment - Tests and measurements - Part 15-1: Connector tests (mechanical) - Test 15a: Contact retention in insert

GSO IEC 60512-25-2:2015 电子设备连接器 测试和测量 第25-2部分：测试 25b 衰减（插入损耗）

This part of IEC 60512 is applicable to electrical connectors, sockets, cable assemblies or interconnection systems. This standard describes a frequency and a time domain method to measure attenuation/ insertion loss as a function of frequency. NOTE “Attenuation” is referenced throughout the document. Test professionals must use the appropriate term (attenuation or insertion loss) when summarizing and reporting the test measurements according to the type of specimen and transmission line being measured.

Connectors for electronic equipment - Tests and measurements - Part 25-2: Test 25b - Attenuation (insertion loss)

GSO IEC 60512-5-2:2015 电子设备连接器 测试和测量 第5-2部分：载流能力测试 测试 5b：电流 温度降额

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to detail a standard test method to assess the current-carrying capacity of electromechanical components at elevated ambient temperature.

Connectors for electronic equipment - Tests and measurements - Part 5-2: Current-carrying capacity tests - Test 5b: Current-temperature derating

GSO IEC 60512-16-16:2015 电子设备连接器 测试和测量 第16-16部分：触点和端子的机械测试 测试 16p：扭转强度 固定公接头

This part of IEC 60512, when required by the detail specification, is used for testing electomechanical components within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to determine the ability of a fixed male tab and its fixing to withstand a specified torque. If so specified in the detail specification, forces other than torsional may be applied.

Connectors for electronic equipment - Tests and measurements - Part 16-16: Mechanical tests on contacts and terminations - Test 16p: Torsional strength, fixed male tabs

GSO IEC 60512-5-1:2015 电子设备连接器 测试和测量 第5-1部分：载流能力测试 测试 5a：温升

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to detail a standard test method to assess the ability of a component to carry its specified current, at room temperature, without exceeding a specified temperature rise.

Connectors for electronic equipment - Tests and measurements - Part 5-1: Current-carrying capacity tests - Test 5a: Temperature rise

GSO IEC 60512-6-3:2015 电子设备连接器 测试和测量 第6-3部分：动态应力测试 测试 6c：冲击

1.1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to withstand specified severities of shock.

Connectors for electronic equipment - Tests and measurements - Part 6-3: Dynamic stress tests - Test 6c: Shock

GSO IEC 60512-25-4:2015 电子设备连接器 测试和测量 第25-4部分：测试 25d 传播延迟

This part of IEC 60512 applies to electrical connectors, sockets, cable assemblies or interconnection systems. This standard describes a method for measuring the time it takes for a digital signal to propagate from one specified point to a second specified point.

Connectors for electronic equipment - Tests and measurements - Part 25-4: Test 25d - Propagation delay

GSO IEC 60512-16-4:2015 电子设备连接器 测试和测量 第16-4部分：触点和端子的机械测试 测试 16d：拉伸强度（压接连接）

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to determine the tensile strength of a crimped connection.

Connectors for electronic equipment - Tests and measurements - Part 16-4: Mechanical tests on contacts and terminations - Test 16d: Tensile strength (crimped connections)

GSO IEC 60603-7-7:2015 电子设备连接器 第7-7部分：用于频率高达 600 MHz 的数据传输的 8 路、屏蔽、自由和固定连接器的详细规范

This part of IEC 60603 covers 8-way, shielded, free and fixed connectors, references dimensional, mechanical, electrical and environmental characteristics and tests in IEC 60603-7 and IEC 60603-7-1, and specifies electrical transmission requirements for frequencies up to 600 MHz. These connectors are typically used as category 7 connectors in class F cabling systems specified in ISO/IEC 11801. These connectors are intermateable and interoperable with other IEC 60603-7 series connectors as defined in Clause 2 of IEC 60603-7-1,

Connectors for electronic equipment - Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors for data transmission with frequencies up to 600 MHz

GSO IEC 60512-11-7:2015 电子设备连接 测试和测量 第 11 7 部分：气候测试 测试 11(g)：流动混合气体腐蚀测试

This part of IEC 60512 defines a standard test method, Test 11g, to assess the effects of a controlled atmosphere polluted by gases at very low concentration on electrical contacts or connections.

Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test

GSO IEC 61076-3-116:2015 电子设备连接器 产品要求 第3-116部分：矩形连接器 用于与八路屏蔽和无护套连接器一起使用的保护外壳的详细规范 频率高达 600 MHz 适用于包含电源链接口的工业环境

This part of IEC 61076 covers protective housings for upgrading existing 8-way shielded and unshielded connectors utilizing the interface described in IEC 60603-7-2, IEC 60603-7-3, IEC 60603-7-4, IEC 60603-7-5, and IEC 60603-7-7 to IP65 and IP67 ratings, according to IEC 60529, for use in industrial environments. The housings cover a variety of different locking mechanisms according to this International Standard and a variety of different mounting configurations and termination types which are detailed in IEC 60603-7. Common mating configuration for all variants are defined in IEC 60603-7. The mating dimensions for the housings under Clause 3 allow the mating conditions under IEC 60603-7 to be fulfilled. The fully assembled variants (connectors) described in this standard incorporate fixed and free connectors which are fully compliant with IEC 60603-7.

Connectors for electronic equipment - Product requirements - Part 3-116: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for frequencies up to 600 MHz for industrial environments

GSO IEC 60512-25-1:2015 电子设备连接器 测试和测量 第25-1部分：测试 25a 串扰比

This part of IEC 60512 applies to interconnect assemblies, such as electrical connectors, sockets and cable assemblies. This standard describes test procedures for measuring the magnitude of the electric and magnetic coupling between driven and quiet lines of an interconnect assembly. Both time domain (method A) and frequency domain methods (method B) for single-ended and differential transmission are described. Insertion and reference fixture techniques are also described.

Connectors for electronic equipment - Tests and measurements - Part 25-1: Test 25a - Crosstalk ratio

GSO IEC 60512-12-4:2015 电子设备连接器 测试和测量 第12-4部分：焊接测试 测试 12d：耐焊接热、焊浴法

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to assess the ability of a connector to withstand the heating stresses produced by a mass soldering operation.

Connectors for electronic equipment - Tests and measurements - Part 12-4: Soldering tests - Test 12d: Resistance to soldering heat, solder bath method

GSO IEC 60512-11-4:2015 电子设备连接器 测试和测量 第11-4部分：气候测试 测试 11d：温度快速变化

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to withstand rapid change of temperature in air such as might occur during storage, transportation and use.

Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature