33.180.01 光纤系统综合 标准查询与下载

IEC TR 63100:2017 无线电通信用传输设备.频谱测量用光纤无线电技术.100GHz频谱测量设备

Transmitting equipment for radiocommunication - Radio-over-fibre technologies for spectrum measurement - 100-GHz spectrum measurement equipment

IEC 61745:2017 光学纤维几何参数测量装置校准端面影像分析程序

This document describes the calibration of test sets that perform end-face image analysis, also known as "near-field" or "grey-scale" analysis. The principles, however, can be applied to test sets of a different type. The procedures outlined are performed by calibration laboratories and by the manufacturers or users of geometry test sets, for the purpose of calibrating geometry test sets and for evaluating the uncertainties in measurements made on calibrated test sets. The calibration of fibre coating or cable measurement test sets is not covered by this document.

End-face image analysis procedure for the calibration of optical fibre geometry test sets

ITU-T G SUPP 51-2017 无源光网络保护注意事项

Passive optical network protection considerations

IEC TR 61282-15:2017 光纤通信系统设计指南. 第15部分: 电缆设施和连接. 终端有MPO连接器的多光缆设施试验

This part of IEC 61282 provides guidance for the testing of multi-fibre cable, multimode or single-mode, terminated with plugs described in IEC 61754-7 (all parts) (multiple-fibre push on - MPO). Guidance is provided on the measurement of attenuation, polarity, length and optical return loss. The cabling can be installed in a variety of environments, including residential, commercial, industrial, and data centre premises, and possibly in outside plant environments.

Fibre optic communication system design guides - Part 15: Cable plant and link - Testing multi-fibre optic cable plant terminated with MPO connectors

IEC 62496-2:2017 光学电路板. 基本试验和测量程序. 第2部分: 光学电路板光学特性测量条件定义通用指南

This part of IEC 62496 specifies a method of defining the conditions for measurements of optical characteristics of optical circuit boards. The method comprises the use of code reference look-up tables to identify different critical aspects of the measurement environment. The values extracted from the tables are used to construct a measurement identification code, which, in itself, captures sufficient information about the measurement conditions, so as to ensure consistency of independently measured results within an acceptable margin. Recommended measurement conditions are specified to minimise further variation in independently measured results.

Optical circuit boards - Basic test and measurement procedures - Part 2: General guidance for definition of measurement conditions for optical characteristics of optical circuit boards

YD/T 1688.3-2017 xPON光收发合一模块技术条件 第3部分:用于GPON光线路终端/光网络单元(OLT/ONU)的光收发合一模块

本部分规定了用于GPON光线路终端/光网络单元(OLT/ONU)光收发合一模块(以下简称“GPON光模块”)的缩略语、术语和定义、技术要求、测试方法、可靠性试验、电磁兼容试验、检验规则、标志、包装、运输和贮存。 本部分适用于GPON光模块。

Technical specification of optical transceiver module for xPON.Part 3: Optical transceiver module for GPON OLT/ONU

YD/T 3250-2017 智能光分配网络 光纤活动连接器

本标准规定了智能光分配网络光纤活动连接器(以下简称为智能光纤连接器)的术语和定义、技术要求、测试方法、质量评定程序、检验规则、标志、包装、运输和贮存等要求。 本标准适用于智能光分配网络用光纤活动连接器，其他智能光纤连接设施中的智能光纤活动连接器也可参考使用。

Intelligent optical distribution network.Optical fiber connector

YD/T 2005-2017 用于光纤通道的光收发模块技术条件

本标准规定了用于光纤通道的光收发模块的技术要求、测试方法、可靠性试验、电磁兼容试验要求、检验规则、标志、包装、运输和贮存等要求。 本标准适用于数据传输速率为100Mbytes/s、200Mbytes/s、400Mbytes/s、1200Mbytes/s、1600Mbytes/s、3200Mbytes/s的光纤通道用的光收发模块(以下简称“模块”)。

The technical specifications of optical transceivers for fiber channel

YD/T 1688.7-2017 xPON光收发合一模块技术条件 第7部分:内置MAC功能的光网络单元(ONU)光收发合一模块

本部分规定了内置MAC功能的PON ONU用光收发合一模块(以下简称为ONU光模块)的缩略语、术语和定义、技术要求、测试方法、可靠性试验、电磁兼容试验、检验规则、标志、包装、运输和贮存要求。 本部分适用于xPON网络中内置MAC功能的ONU用光收发合一模块。

Technical specification of optical transceiver module for xPON.Part 7: Optical transceiver module embedded with MAC for ONU

JIS C 61280-2-2:2017 纤维光学通信子系统试验程序.第2-2部分:光眼图、波形和消光比的测量

Fiber optic communication subsystem test procedures -- Part 2-2: Optical eye pattern, waveform and extinction ratio measurement

JIS C 61280-1-3:2017 纤维光学通信子系统试验程序.第1-3部分:中心波长和谱宽测量

Fiber optic communication subsystem test procedures -- Part 1-3: Central wavelength and spectral width measurement

GY/T 306.1-2017 有线电视网络光纤到户系统技术规范 第1部分：总体技术要求

Technical specifications for cable television network fiber-to-the-home systems Part 1: General technical requirements

IEC 61280-4-4:2017 纤维光学通信子系统基本试验程序.第4-4部分:已安装链路的偏振模式色散测量

This part of IEC 61280 provides uniform methods of measuring polarization mode dispersion (PMD) of single-mode installed links. An installed link is the optical path between transmitter and receiver, or a portion of that optical path. These measurements can be used to assess the suitability of a given link for high bit rate applications, or to provide insight on the relationships of various related transmission attributes. This document focuses on the measurement methods and requirements for measuring long lengths of installed cabling that can also include other optical elements, such as splices, connectors, amplifiers, chromatic dispersion compensating modules, dense wavelength division multiplexing or multiplexer (DWDM) components, multiplexers, wavelength selective switches, re-configurable optical add drop multiplexer (ROADMS). This document focuses on the apparatus, procedures, and calculations needed to complete measurements. IEC TR 61282-9 explains the theory behind the test methods.

Fibre optic communication subsystem test procedures - Part 4-4: Cable plants and links - Polarization mode dispersion measurement for installed links

IEC 60050-731:1991/AMD1:2016 修改件1.国际电工词汇.第731部分:光纤通信

Amendment 1 - International electrotechnical vocabulary - Part 731: Optical fibre communication

ITU-T G.971-2016 光纤海底电缆的一般特性(第15研究组)

General features of optical fibre submarine cable systems (Study Group 15)

NF C93-804-2*NF EN 61746-2:2016 光时域反射计(OTDR)的校准. 第2部分: 多模光纤用OTDR

Calibration of optical time-domain reflectometers (OTDR) - Part 2 : OTDR for multimode fibres

EN 62343-3-2:2016 动态模块 第 3-2 部分：性能规范模板 光通道监视器

IEC 62343-3-2:2016(E) provides a performance specification template for optical channel monitors. The objective of this performance specification template is to provide a framework for the performance specification of the optical channel monitor. Additional specification parameters may be included for detailed product specifications or performance specifications. However, specification parameters specified in this document should not be removed from the detail product specifications or performance specifications. This document outlines the parameters that are used to specify the performance of the optical channel monitor. Keywords: optical channel monitor (OCM)

Dynamic modules - Part 3-2: Performance specification templates - Optical channel monitor

YD/T 3130-2016 通信用智能小型化热插拔（Smart SFP）光收发合一模块

Smart miniaturized hot-pluggable (Smart SFP) optical transceiver module for communications

YD/T 3125.1-2016 通信用增强型SFP光收发合一模块（SFP+） 第1部分：8.5Gb/s和10Gb/s

Enhanced SFP optical transceiver module for communications (SFP+) Part 1: 8.5Gb/s and 10Gb/s

YD/T 3126.1-2016 集成可调谐光源模块 第1部分：接口

Integrated Tunable Light Source Module Part 1: Interface