共找到 800 条与 光纤系统综合 相关的标准,共 54 页
Fibre optic interconnecting devices and passive components - Interface standard for fibre management systems - Part 1: General and guidance
Dynamic Modules - Part 6-11: Design guidelines - Software and hardware interface for optical multicast switches
100Gbit/s dual polarization quadrature phase shift keying (DP-QPSK) optical transceiver module Part 4: CFP2-DCO optical module
Enhanced SFP optical transceiver module for communications (SFP+) Part 2: 25Gbit/s
40Gbit/s/100Gbit/s intensity modulated pluggable optical transceiver module Part 5: 4×25Gbit/s CFP2
400Gbit/s phase modulated optical transceiver module Part 1: 2×200Gbit/s
Technical requirements for optical fiber preforms for communications Part 3: Non-dispersion shifted single-mode optical fiber assembly preforms with extended wavelength range
400Gbit/s intensity modulated pluggable optical transceiver module Part 2: 8×50Gbit/s
Integrated Optical Power Detector (IPM)
Intelligent optical distribution network management system testing method
400Gbit/s intensity modulated pluggable optical transceiver module Part 1: 16×25Gbit/s
Integrated Tunable Laser Components Part 3: Dual Channel Components
Optical fiber movable connectors Part 5: MPO type
Amendment 4 - International Electrotechnical Vocabulary (IEV) - Part 731: Optical fibre communication
Dynamic modules - Part 2-1: Reliability qualification - Test template
IEC 61280-4-1: 2019 is applicable to the measurement of attenuation of installed optical fibre cabling plant using multimode optical fibre. This cabling plant can include multimode optical fibres, connectors, adapters, splices, and other passive devices. The cabling can be installed in a variety of environments including residential, commercial, industrial, and data centre premises, as well as outside plant environments. The test equipment used in this document has one single fibre connector interface or two single fibre connector interfaces. In this document, the optical fibres that are addressed include sub-categories A1-OMx, where x = 2, 3, 4 and 5 (50/125 μm) and A1-OM1 (62,5/125 μm) multimode optical fibres, as specified in IEC 60793-2-10. The attenuation measurements of the other multimode categories can be made using the approaches of this document, but the source conditions for the other categories have not been defined. This third edition cancels and replaces the second edition, published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) changes to Annex F on encircled flux to harmonise with IEC TR 62614-2, but keeping the encircled flux limits defined in Tables F.2 to F.5 unchanged; b) addition of an equipment cord method in Annex D; c) inclusion of testing bend insensitive multimode optical fibre; d) updates to measurement uncertainty; e) definition of additional cabling configurations; f) changes to Table 5 on spectral requirements. Keywords: measurement of attenuation
Fibre-optic communication subsystem test procedures - Part 4-1: Installed cabling plant - Multimode attenuation measurement
Fibre optic communication system design guides - Part 14: Determination of the uncertainties of attenuation measurements in fibre plants
Fibre optic communication system design guides - Part 14: Determination of the uncertainties of attenuation measurements in fibre plants
Fibre optic communication system design guidelines - Part 5: Accommodation and compensation of chromatic dispersion
IEC 62129-3:2019 describes the calibration of optical frequency meters using an optical frequency comb as an internal reference. It is applicable to instruments measuring the optical frequency emitted from sources that are typical for the fibre-optic communications industry. It is assumed that the optical radiation will be coupled to the optical frequency meter by a single-mode optical fibre. This document is part of the IEC 62129 series on the calibration of wavelength/optical frequency measurement instruments. Refer to IEC 621291 [3] for the calibration of optical spectrum analyzers, and refer to IEC 62129-2 [4] for calibration of Michelson interferometer single wavelength meters. This first edition cancels and replaces IEC TS 62129-3, published in 2014. This edition includes the following significant technical changes with respect to the previous edition: a) text has been added to 5.2.3 about calibration at a second optical frequency; b) Annex D is now normative; c) Subclause 4.2 has been improved; d) measurement method of frequency has been moved to Annex B; e) example of optical frequency comb has been moved to Annex C; f) frequency-dependence uncertainty has been moved to Annex D. Keywords: calibration of optical frequency meters
Calibration of wavelength/optical frequency measurement instruments - Part 3:Optical frequency meters internally referenced to a frequency comb
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号