33.180.01 光纤系统综合 标准查询与下载

OVE EN IEC 61757-5-1:2021 光纤传感器 第 5-1 部分：倾斜测量 基于光纤布拉格光栅的倾斜传感器（IEC 86C/1699/CDV）（英文版）

Fibre optic sensors - Part 5-1: Tilt measurement - Tilt sensors based on fibre Bragg gratings (IEC 86C/1699/CDV) (english version)

OVE EN IEC 61757-2-1:2021 光纤传感器 第 2-1 部分：温度测量 基于光纤布拉格光栅的温度传感器（IEC 86C/1702/CDV）

Fibre Optic Sensors - Part 2-1: Temperature measurement - Temperature sensors based on fibre Bragg gratings (IEC 86C/1702/CDV)

OVE EN IEC 62496-4-1:2021 光电路板 第 4-1 部分：接口标准 使用单排十二通道 PMT 连接器的端接波导 OCB 组件（德文版）

Optical circuit boards - Part 4-1: Interface standards - Terminated waveguide OCB assembly using single-row twelve-channel PMT connectors (german version)

T/SIAA 000006-2020 住宅入户光缆端接及户内布线技术指南

本文件确立了对住宅户内入户光缆的端接及家庭网关的安装位置选择的原则，提供了入户光缆敷设方案和布放方法、线缆敷设要求、家庭原有弱电线缆的改造方式以及配套设备选型的指导。

Technical guide for drop fibre cable termination and indoor cables wiring

DIN EN IEC 62496-4-1:2020 光电路板. 第4-1部分: 接口标准. 使用单排十二通道PMT连接器的端接波导OCB组件(IEC 62496-4-1-2019); 德文版 EN IEC 62496-4-1-2019

This part of IEC 62496-4 defines the standard interface dimensions for a terminated single row waveguide optical circuit board (OCB) assembly (assembly) using a connector for polymer waveguides connected with MT (PMT) connector. The assembly is intermateable with a type MT connec

Optical circuit boards - Part 4-1: Interface standards - Terminated waveguide OCB assembly using single-row twelve-channel PMT connectors (IEC 62496-4-1:2019); German version EN IEC 62496-4-1:2019

LST EN IEC 61280-4-5:2020 光纤通信子系统测试程序 第 4-5 部分：已安装的布线设备 使用带有 MPO 接口的测试设备对 MPO 端接光纤布线设备进行衰减测量（IEC 61280-4-5:2020）

Fibre-optic communication subsystem test procedures - Part 4-5: Installed cabling plant - Attenuation measurement of MPO terminated fibre optic cabling plant using test equipment with MPO interfaces (IEC 61280-4-5:2020)

KS C 6918-2020 光纤光谱分析仪测试方法

Test methods of fiber-optic spectrum analyzer

KS C IEC 62148-2-2020 光纤有源器件和器件 封装和接口标准 第2部分：SFF MT-RJ 10针收发器

Fibre optic active components and devices－Package and interface standards－Part 2：SFF MT-RJ 10-pin transceivers

KS C IEC 62148-5-2020 光纤有源器件和器件 封装和接口标准 第5部分：SC 1×9光纤模块

Fibre optic active components and devices－Package and interface standards－Part 5：SC 1×9 fibre optic modules

KS C 6928-2020 光纤光功率计测试方法

Test methods of optical power meters for optical fiber

KS C 6929-2020 光纤测试源的测试方法

Test methods for fiber optic test sources

EN IEC 61280-4-5:2020 光纤通信子系统测试程序 第 4-5 部分：已安装的布线设备 使用带有 MPO 接口的测试设备对 MPO 端接光纤布线设备进行衰减测量

IEC 61280-4-5: 2020 is applicable to the measurement of attenuation and determination of polarity and length of installed multimode and single-mode optical fibre cabling plant, terminated with MPO connectors, using test equipment having an MPO interface. This cabling plant can include multimode or single-mode optical fibres, connectors, adapters, splices, and other passive devices. The cabling can be installed in a variety of environments including residential, commercial, industrial, and data centre premises, as well as outside plant environments. In this document, the optical fibres that are addressed include sub-categories A1-OMx, where x = 2, 3, 4 and 5 (50/125 μm) multimode optical fibres, as specified in IEC 60793-2-10, and category B-652 and B-657 (9/125 μm) single-mode optical fibres, as specified in IEC 60793-2-50. The attenuation measurements of the other multimode and single-mode categories can also be made using a light source and power meter (LSPM) or optical time domain reflectometer (OTDR) utilising an internal or external optical switch having one MPO interface. Multimode measurements are made with an 850 nm source because transceivers used for parallel optics applications having an MPO interface only operate at 850 nm; 1 300 nm measurements are optional. Single-mode measurements are made with a 1 310 nm and/or 1 550 nm source because transceivers used for parallel optics applications having an MPO interface operate at these wavelengths. This document does not include descriptions of cabling that is not exclusively MPO to MPO.

Fibre-optic communication subsystem test procedures - Part 4-5: Installed cabling plant - Attenuation measurement of MPO terminated fibre optic cabling plant using test equipment with MPO interfaces

IEC TR 62572-4:2020 RLV 纤维光学有源元件和器件可靠性标准第4部分:插座式光收发器光学连接器端面清洁方法指南

Fibre optic active components and devices - Reliability standards - Part 4: Guidelines for optical connector end-face cleaning methods for receptacle style optical transceivers

IEC TR 62572-4:2020 纤维光学有源元件和器件可靠性标准第4部分:插座式光收发器光学连接器端面清洁方法指南

Fibre optic active components and devices - Reliability standards - Part 4: Guidelines for optical connector end-face cleaning methods for receptacle style optical transceivers

BS EN IEC 62614-1:2020 光纤 多模发射条件 测量多模衰减的发射条件要求

What is BS EN IEC 62614 ‑ 1 about?    BS EN IEC 62614 is a series on fibre optics. BS EN IEC 62614 ‑ 1 describes the launch condition requirements used for measuring multimode attenuation in passive components and in installed cable plants.   In BS EN IEC 62614 ‑ 1 , the fibre types that are addressed include category A1-OMx, where x = 2, 3, 4 and 5 (50 μm/125 μm), and A1-OM1 (62,5 μm/125 μm) multimode fibres. BS EN IEC 62614 ‑ 1 can be suitable for multimode attenuation measurements for other multimode categories and/or other wavelengths. BS EN IEC 62614 ‑ 1 describes launch condition requirements for optical attenuation using sources with a controlled encircled flux (EF).  

Fibre optics. Multimode launch conditions - Launch condition requirements for measuring multimode attenuation

YD/T 3356.2-2020 100Gb/s及以上速率光收发组件 第2部分：4×25Gb/s LR4

Optical transceiver components at 100Gb/s and above Part 2: 4×25Gb/s LR4

YD/T 3692.2-2020 智能光分配网络 智能门禁技术要求 第2部分：接口要求

Intelligent optical distribution network intelligent access control technical requirements Part 2: Interface requirements

YD/T 2798.2-2020 用于光通信的光收发合一模块测试方法 第2部分：多波长型

Test methods for optical transceiver modules used in optical communications Part 2: Multi-wavelength type

YD/T 2759.2-2020 单纤双向光收发合一模块 第2部分：25Gb/s

Single fiber bidirectional optical transceiver module Part 2: 25Gb/s

EN IEC 62614-1:2020 光纤 多模发射条件 第1部分：测量多模衰减的发射条件要求

IEC 62614-1: 2020 describes the launch condition requirements used for measuring multimode attenuation in passive components and in installed cable plants. In this document, the fibre types that are addressed include category A1-OMx, where x = 2, 3, 4 and 5 (50 µm/125 µm), and A1-OM1 (62,5 µm/125 µm) multimode fibres, as specified in IEC 60793-2-10. The nominal test wavelengths detailed are 850 nm and 1 300 nm. This document can be suitable for multimode attenuation measurements for other multimode categories and/or other wavelengths, but the source condition for other categories and wavelengths are not defined here. The purpose of these requirements is as follows: to ensure consistency of field measurements when different types of test equipment are used; to ensure consistency of factory measurements when different types of test equipment are used; to ensure consistency of field measurements when compared with factory measurements. This document describes launch condition requirements for optical attenuation using sources with a controlled encircled flux (EF).

Fibre optics - Multimode launch conditions - Part 1: Launch condition requirements for measuring multimode attenuation