33.180.20 纤维光学和光学互连器件 标准查询与下载

EN IEC 62148-22:2023 光纤有源元件和设备 封装和接口标准 第22部分：带温度控制单元的 25 Gbit/s 直接调制激光器封装

IEC 62148-22: 2023 defines the physical dimensions and interface specifications for directly modulated laser (DML) devices used in optical telecommunication and optical data transmission applications. The intent of this document is to adequately specify the physical requirements for DML devices so as to enable mechanical interchangeability of laser devices or transmitters complying with this document both at the printed circuit board and for any panel-mounting requirements.

Fibre optic active components and devices - Package and interface standards - Part 22: 25 Gbit/s directly modulated laser packages with temperature control unit

EN IEC 62149-12:2023 光纤有源元件和设备 性能标准 第12部分：用于光纤系统模拟无线电的分布式反馈激光二极管设备

IEC 62149-12:2023 This part of IEC 62149 defines performance specifications for distributed feedback laser diode (DFB-LD) devices used in analogue radio over fibre (RoF) systems. It defines product performance requirements together with a series of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a “once-off” basis to prove a product’s ability to satisfy the performance requirements.

Fibre optic active components and devices - Performance standards - Part 12: Distributed feedback laser diode device for analogue radio over fibre systems

BS EN IEC 62149-4:2023 光纤有源元件和装置 性能标准 1300nm 光纤收发器 用于千兆位以太网应用

1   Scope This part of IEC 62149 defines performance specifications for 1 300 nm fibre optic transceiver modules used for the ISO/IEC/IEEE 8802‑3 Gigabit Ethernet application. This document contains definitions for product performance requirements as well as a series of tests and measurements, for which clearly defined conditions, severities and pass/fail criteria are provided. The tests are intended to be run on a "once-off" basis to prove any product’s ability to satisfy the performance standard’s requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard but will then be controlled by a quality assurance/quality conformance program.

Fibre optic active components and devices. Performance standards. 1 300 nm fibre optic transceivers for Gigabit Ethernet application

IEC 62148-22:2023 光纤有源元件和器件.封装和接口标准.第22部分:带温度控制单元的25Gbit/s直接调制激光封装

Fibre optic active components and devices - Package and interface standards - Part 22: 25 Gbit/s directly modulated laser packages with temperature control unit

IEC 62149-12:2023 光纤有源元件和器件.性能标准.第12部分:光纤模拟无线电系统用分布式反馈激光二极管器件

Fibre optic active components and devices - Performance standards - Part 12: Distributed feedback laser diode device for analogue radio over fibre systems

23/30469447 DC BS EN IEC 61300-3-46 光纤互连装置和无源元件 基本测试和测量程序 第 3-46 部分 检查和测量 矩形套圈的孔径

BS EN IEC 61300-3-46. Fibre optic interconnecting devices and passive components. Basic test and measurement procedures - Part 3-46. Examinations and Measurements. Bore diameter in rectangular ferrules

EN IEC 62149-4:2023 光纤有源元件和设备 性能标准 第4部分：用于千兆以太网应用的 1 300 nm 光纤收发器

IEC 62149-4:2022 is available as IEC 62149-4:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62149-4:2022 defines performance specifications for 1 300 nm fibre optic transceiver modules used for the ISO/IEC/IEEE 8802-3 Gigabit Ethernet application. This document contains definitions for product performance requirements as well as a series of tests and measurements, for which clearly defined conditions, severities and pass/fail criteria are provided. The tests are intended to be run on a "once-off" basis to prove any product’s ability to satisfy the performance standard’s requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard but will then be controlled by a quality assurance/quality conformance program. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the normative references are updated; - the condition "for short periods" in 4.1 is removed; - the absolute limiting rating for soldering temperature in Table 1 is modified; - the maximal optical output power (multimode fibre) in Table 4 is increased from −3,5 dBm to −3 dBm, to align value with the referenced document; - a note is added to Table 7 to clarify that out-of-specification products are not allowed to pass the performance tests.

Fibre optic active components and devices - Performance standards - Part 4: 1 300 nm fibre optic transceivers for Gigabit Ethernet application

23/30469024 DC BS EN IEC 61300-2-19 光纤互连装置和无源元件 基本测试和测量程序 第 2-19 部分 测试 湿热（稳态）

BS EN IEC 61300-2-19. Fibre optic interconnecting devices and passive components. Basic test and measurement procedures - Part 2-19. Tests. Damp heat (steady state)

IEC TR 62627-01:2023 光纤互连器件和无源元件.第01部分:光纤连接器清洁方法

Fibre optic interconnecting devices and passive components - Part 01: Fibre optic connector cleaning methods

IEC TR 62627-01:2023 RLV 光纤互连器件和无源元件.第01部分:光纤连接器清洁方法

Fibre optic interconnecting devices and passive components - Part 01: Fibre optic connector cleaning methods

IEC 61300-2-1:2023 RLV 光纤互连器件和无源元件.基本试验和测量程序.第2-1部分:试验.振动（正弦）

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-1: Tests - Vibration (sinusoidal)

IEC 61300-2-1:2023 光纤互连器件和无源元件.基本试验和测量程序.第2-1部分:试验.振动（正弦）

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-1: Tests - Vibration (sinusoidal)

23/30468244 DC BS EN IEC 61300-3-50 光纤互连装置和无源元件 基本测试和测量程序 第 3-50 部分 检查和测量 光空间开关的串扰

BS EN IEC 61300-3-50. Fibre optic interconnecting devices and passive components. Basic test and measurement procedures - Part 3-50. Examinations and measurements. Crosstalk for optical spatial switches

IEC 61300-2-18:2023 RLV 光纤互连器件和无源元件.基本试验和测量程序.第2-18部分:试验.干热

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-18: Tests - Dry heat

IEC 61300-2-18:2023 光纤互连器件和无源元件.基本试验和测量程序.第2-18部分:试验.干热

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-18: Tests - Dry heat

23/30468217 DC BS IEC 60875-1 光纤互连装置和无源元件 非波长选择光纤分支装置 第 1 部分：通用规范

BS IEC 60875-1. Fibre optic interconnecting devices and passive components. Non-wavelength-selective fibre optic branching devices - Part 1. Generic specification

IEC 62149-4:2022 光纤有源元件和设备 性能标准 第4部分：用于千兆以太网应用的 1 300 nm 光纤收发器

Fibre optic active components and devices - Performance standards - Part 4: 1 300 nm fibre optic transceivers for Gigabit Ethernet application

BS EN IEC 61300-3-35:2022 光纤互连装置和无源元件 基本测试和测量程序 检查和测量 光纤连接器和光纤插芯收发器的目视检查

1   Scope This part of IEC 61300 is concerned with the observation and classification of debris , scratches and defects . The inspection requirements are based on IEC TR 62627‑05. Advice for cleaning of contamination from fibres/ferrule is found in IEC TR 62627‑01 and a recommendation is given in Annex D. IEC TR 62572‑4 provides the cleaning method for a stub for optical transceivers. Visual inspection is in addition to, and does not replace measurement of performance parameters such as attenuation and return loss, or end face parameters. The dimensions specified are chosen such that they can be easily estimated. Not only the zones A and B on the fibre are inspected for defects and scratches but the whole contact area (where the two fibres/ferrules meet when mated) needs to be inspected for contamination (this is up to 250 µm diameter for cylindrical ferrules and the whole ferrule surface for rectangular ferrules). The objectives of this document are the following: • specify the minimum criteria for a microscope to be compliant to this document; • specify the procedure and criteria for inspecting fibre-optic end faces for cleanliness to determine if the end faces are fit for use. All connector optical interfaces (IEC 61755 series and IEC 63267 series) are based on physical contact between fibre cores; • provide quantitative criteria for the analysis of end face images. ...

Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Examinations and measurements. Visual inspection of fibre optic connectors and fibre-stub transceivers

BS EN IEC 62148-12:2004+A1:2022 光纤有源元件和装置 封装和接口标准 带同轴射频连接器的激光发射器

This part of IEC 62148 covers physical interface specifications of laser diode devices for optical fibre communication. The intent of this part of IEC 62148 is to adequately specify the physical requirements of an optical transmitter that will enable mechanical interchangeability of transmitters to this standard both at the printed circuit board and for any panel-mounting requirement.

Fibre optic active components and devices. Package and interface standards - Laser transmitters with a coaxial RF connector

KS C IEC 61300-3-3-2022 光纤互连器件和无源元件.基本试验和测量程序.第3-3部分:检查和测量.衰减和回波损耗变化的主动监测

Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 3-3: Examinations and measurements — Active monitoring of changes in attenuation and return lo