33.180.20 纤维光学和光学互连器件 标准查询与下载

IEC 61300-3-45:2023 RLV 光纤互连装置和无源元件 - 基本测试和测量程序 - 第 3-45 部分：检查和测量 - 随机配合多光纤连接器的衰减

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-45: Examinations and measurements - Attenuation of random mated multi-fibre connectors

IEC 61300-3-45:2023 光纤互连装置和无源元件 - 基本测试和测量程序 - 第 3-45 部分：检查和测量 - 随机配合多光纤连接器的衰减

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-45: Examinations and measurements - Attenuation of random mated multi-fibre connectors

23/30474618 DC BS EN IEC 61755-3-2 光纤互连装置和无源元件 连接器光学接口 第 3-2 部分 色散未偏移单模物理接触光纤的连接器参数 直径为 2.5 毫米和 1.25 毫米的角度…

BS EN IEC 61755-3-2. Fibre optic interconnecting devices and passive components. Connector optical interfaces - Part 3-2. Connector parameters of dispersion unshifted single-mode physically contacting fibres. angled 2,5 mm and 1,25 mm diameter…

YD/T 4305.1-2023 通信用光电混合活动连接器 第1部分：SC型

本文件规定了通信用SC型光电混合活动连接器（以下简称“光电连接器”）的分类、接口的图形和配合尺寸、端面、光学性能、电气性能、材料和环保符合性等要求，描述了相应的试验方法及质量评定程序、标志、包装、运输及贮存。 本文件适用于园区/室内无线、办公、监控等应用场景下通信用SC型光电混合活动连接器的设计、开发、生产和检验。应用于其它场景的SC型光电混合活动连接器也可参照使用。

Hybrid optoelectronic connectors for communication - Part 1: Type SC

IEC 61300-3-4:2023 光纤互连设备和无源元件 基本测试和测量程序 第 3-4 部分：检查和测量 衰减

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-4: Examinations and measurements - Attenuation

IEC 61300-3-4:2023 RLV 光纤互连器件和无源元件.基本试验和测量程序.第3-4部分:检查和测量.衰减

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-4: Examinations and measurements - Attenuation

BS EN IEC 62148-22:2023 光纤有源元件和装置 封装和接口标准 带温度控制单元的 25 Gbit/s 直接调制激光封装

1   Scope This part of IEC 62148 defines the physical dimensions and interface specifications for directly modulated laser ( DML ) devices used in optical telecommunication and optical data transmission applications. The intent of this document is to adequately specify the physical requirements for DML devices so as to enable mechanical interchangeability of laser devices or transmitters complying with this document both at the printed circuit board and for any panel-mounting requirements.

Fibre optic active components and devices. Package and interface standards - 25 Gbit/s directly modulated laser packages with temperature control unit

BS EN IEC 62149-12:2023 光纤有源元件和装置 性能标准 用于光纤模拟无线电系统的分布式反馈激光二极管器件

1   Scope This part of IEC 62149 defines performance specifications for distributed feedback laser diode ( DFB-LD ) devices used in analogue radio over fibre ( RoF ) systems. It defines product performance requirements together with a series of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a "once-off" basis to prove a product’s ability to satisfy the performance requirements.

Fibre optic active components and devices. Performance standards - Distributed feedback laser diode device for analogue radio over fibre systems

23/30472828 DC BS EN IEC 61300-2-37 光纤互连装置和无源元件 基本测试和测量程序 第 2-37 部分 测试 用于光纤保护外壳和硬化连接器的电缆弯曲

BS EN IEC 61300-2-37. Fibre optic interconnecting devices and passive components. Basic test and measurement procedures - Part 2-37. Tests. Cable bending for fibre optic protective housings and hardened connectors

BS EN IEC 61300-2-1:2023 光纤互连装置和无源元件 基本测试和测量程序 测试 振动（正弦）

1   Scope This part of IEC 61300 evaluates the effects of vibration on fibre optic devices at the predominant frequency ranges and magnitudes that are encountered during field service on attenuation. NOTE Most vibrations encountered in service are not of a simple harmonic nature. However, it has been shown that tests based on vibrations of this type are satisfactory to simulating actual service.

Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Tests. Vibration (sinusoidal)

T/QGCML 717-2023 WDM波分复用器

本文件规定了WDM波分复用器的术语和定义、缩略语、产品分类、技术要求、试验方法、检验规则、标志、包装、运输及存储的要求。 本文件适用于WDM波分复用器产品。

WDM wavelength division multiplexer

EN IEC 62148-22:2023 光纤有源元件和设备 封装和接口标准 第22部分：带温度控制单元的 25 Gbit/s 直接调制激光器封装

IEC 62148-22: 2023 defines the physical dimensions and interface specifications for directly modulated laser (DML) devices used in optical telecommunication and optical data transmission applications. The intent of this document is to adequately specify the physical requirements for DML devices so as to enable mechanical interchangeability of laser devices or transmitters complying with this document both at the printed circuit board and for any panel-mounting requirements.

Fibre optic active components and devices - Package and interface standards - Part 22: 25 Gbit/s directly modulated laser packages with temperature control unit

EN IEC 62149-12:2023 光纤有源元件和设备 性能标准 第12部分：用于光纤系统模拟无线电的分布式反馈激光二极管设备

IEC 62149-12:2023 This part of IEC 62149 defines performance specifications for distributed feedback laser diode (DFB-LD) devices used in analogue radio over fibre (RoF) systems. It defines product performance requirements together with a series of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a “once-off” basis to prove a product’s ability to satisfy the performance requirements.

Fibre optic active components and devices - Performance standards - Part 12: Distributed feedback laser diode device for analogue radio over fibre systems

BS EN IEC 62149-4:2023 光纤有源元件和装置 性能标准 1300nm 光纤收发器 用于千兆位以太网应用

1   Scope This part of IEC 62149 defines performance specifications for 1 300 nm fibre optic transceiver modules used for the ISO/IEC/IEEE 8802‑3 Gigabit Ethernet application. This document contains definitions for product performance requirements as well as a series of tests and measurements, for which clearly defined conditions, severities and pass/fail criteria are provided. The tests are intended to be run on a "once-off" basis to prove any product’s ability to satisfy the performance standard’s requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard but will then be controlled by a quality assurance/quality conformance program.

Fibre optic active components and devices. Performance standards. 1 300 nm fibre optic transceivers for Gigabit Ethernet application

IEC 62148-22:2023 光纤有源元件和器件.封装和接口标准.第22部分:带温度控制单元的25Gbit/s直接调制激光封装

Fibre optic active components and devices - Package and interface standards - Part 22: 25 Gbit/s directly modulated laser packages with temperature control unit

IEC 62149-12:2023 光纤有源元件和器件.性能标准.第12部分:光纤模拟无线电系统用分布式反馈激光二极管器件

Fibre optic active components and devices - Performance standards - Part 12: Distributed feedback laser diode device for analogue radio over fibre systems

23/30469447 DC BS EN IEC 61300-3-46 光纤互连装置和无源元件 基本测试和测量程序 第 3-46 部分 检查和测量 矩形套圈的孔径

BS EN IEC 61300-3-46. Fibre optic interconnecting devices and passive components. Basic test and measurement procedures - Part 3-46. Examinations and Measurements. Bore diameter in rectangular ferrules

EN IEC 62149-4:2023 光纤有源元件和设备 性能标准 第4部分：用于千兆以太网应用的 1 300 nm 光纤收发器

IEC 62149-4:2022 is available as IEC 62149-4:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62149-4:2022 defines performance specifications for 1 300 nm fibre optic transceiver modules used for the ISO/IEC/IEEE 8802-3 Gigabit Ethernet application. This document contains definitions for product performance requirements as well as a series of tests and measurements, for which clearly defined conditions, severities and pass/fail criteria are provided. The tests are intended to be run on a "once-off" basis to prove any product’s ability to satisfy the performance standard’s requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard but will then be controlled by a quality assurance/quality conformance program. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the normative references are updated; - the condition "for short periods" in 4.1 is removed; - the absolute limiting rating for soldering temperature in Table 1 is modified; - the maximal optical output power (multimode fibre) in Table 4 is increased from −3,5 dBm to −3 dBm, to align value with the referenced document; - a note is added to Table 7 to clarify that out-of-specification products are not allowed to pass the performance tests.

Fibre optic active components and devices - Performance standards - Part 4: 1 300 nm fibre optic transceivers for Gigabit Ethernet application

23/30469024 DC BS EN IEC 61300-2-19 光纤互连装置和无源元件 基本测试和测量程序 第 2-19 部分 测试 湿热（稳态）

BS EN IEC 61300-2-19. Fibre optic interconnecting devices and passive components. Basic test and measurement procedures - Part 2-19. Tests. Damp heat (steady state)

IEC TR 62627-01:2023 光纤互连器件和无源元件.第01部分:光纤连接器清洁方法

Fibre optic interconnecting devices and passive components - Part 01: Fibre optic connector cleaning methods