33.180.30 光纤放大器 标准查询与下载

DS/EN IEC 61290-1-1:2020 光放大器 测试方法'第1-1部分：功率和增益参数 光谱分析仪方法

Optical amplifiers – Test methods – Part 1-1: Power and gain parameters – Optical spectrum analyzer method

EN IEC 61290-1-1:2020 光放大器 测试方法 第 1-1 部分：功率和增益参数 光谱分析仪方法

IEC 61290-1-1:2020 is available as IEC 61290-1-1:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61290-1-1:2020 applies to all commercially available optical amplifiers (OAs) and optically amplified modules. It applies to OAs using optical fibre amplifiers (OFAs) based on either rare-earth doped fibres or on the Raman effect, semiconductor OAs (SOAs) and planar optical waveguide amplifiers (POWAs). The object of this document is to establish uniform requirements for accurate and reliable measurements, by means of the optical spectrum analyzer (OSA) test method, of the following OA parameters, as defined in IEC 61291-1: - nominal output signal power; - gain; - polarization-dependent gain (PDG); - maximum output signal power; - maximum total output power. In addition, this document provides the test method of: - gain ripple (for SOAs). NOTE All numerical values followed by (‡) are suggested values for which the measurement is assured. The object of this document is specifically directed to single-channel amplifiers. Test methods for multichannel amplifiers are standardized in IEC 61290-10 (all parts). This fourth edition cancels and replaces the third edition published in 2015 and constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: addition of techniques to test gain ripple of SOAs.

Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method

NF C93-805-1-1:2020 光学放大器. 试验方法. 第1-1部分: 功率和增益参数. 光谱分析仪法

La présente partie de l'IEC 61290 s'applique à tous les amplificateurs optiques (OA: optical amplifier) et modules à amplification optique. Elle s'applique aux amplificateurs optiques utilisant des amplificateurs à fibres optiques (OFA: optical fibre amplifier) composés de fibres

Optical amplifiers - Test methods - Part 1-1 : Power and gain parameters - Optical spectrum analyzer method

IEC 61290-1-1:2020 RLV 光放大器.试验方法.第1-1部分:功率和增益参数.光谱分析仪法

Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method

IEC 61290-1-1:2020 光放大器 - 测试方法 - 第1-1部分:功率和增益参数 - 光谱分析仪方法

Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method

BS EN IEC 61290-4-4:2018 光放大器 测试方法 增益瞬态参数 带增益控制的单通道光放大器

What is BS EN IEC 61290 ‑ 4 ‑ 4 - Optical amplifiers about?    BS EN IEC 61290 is a series on optical amplifiers. An optical amplifier is a device that amplifies an  optical signal  directly, without the need to first convert it to an electrical signal. BS EN IEC 61290 ‑ 4 ‑ 4 applies to optical amplifiers (OAs) and optically amplified elementary sub-systems. More specifically, BS EN IEC 61290 ‑ 4 ‑ 4 applies to OAs using active fibres (optical fibre amplifiers, OFAs) containing rare-earth dopants, such as erbium-doped fibre amplifiers (EDFAs), presently commercially available, as indicated in IEC 61291-1 .   BS EN IEC 61290 ‑ 4

Optical amplifiers. Test methods - Gain transient parameters. Single channel optical amplifiers with gain control

JIS C 6123-1:2018 光放大器. 性能规格模板. 第1部分: 单通道光放大器

Optical amplifiers -- Performance specification template -- Part 1: Single channel optical amplifiers

BS EN IEC 61290-4-3:2018 光放大器 测试方法 功率瞬态参数 输出功率控制中的单通道光放大器

What is BS EN IEC 61290 ‑ 4 ‑ 3 - Optical amplifiers about?    BS EN IEC 61290 is a series on optical amplifiers. An optical amplifier is a device that amplifies an  optical signal  directly, without the need to first convert it to an electrical signal. An optical amplifier may be thought of as a  laser  without an  optical cavity , or one in which  feedback  from the cavity is suppressed. BS EN IEC 61290 ‑ 4 ‑ 3

Optical amplifiers. Test methods - Power transient parameters. Single channel optical amplifiers in output power control

EN IEC 61290-4-3:2018 光放大器 测试方法 第 4-3 部分：功率瞬态参数 输出功率控制中的单通道光放大器

Optical amplifiers - Test methods - Part 4-3: Power transient parameters - Single channel optical amplifiers in output power control

DIN EN 62343:2018 动态模块.总则和指引(IEC 62343-2017); 德文版本EN 62343-2017

This Standard applies to all commercially available optical dynamic modules and devices. It describes the products covered by the IEC 62343 series, defines terminology, fundamental considerations and basic approaches. This standard covers performance templates, performance standards, reliability qualification requirements, hardware and software interfaces and related testing methods.

Dynamic modules - General and guidance (IEC 62343:2017); German version EN 62343:2017

IEC 61290-4-4:2018 光学放大器 试验方法 第4-4部分:增益瞬态参数 带增益控制的单通道光放大器

This part of IEC 61290-4 applies to optical amplifiers (OAs) and optically amplified elementary sub-systems. More specifically@ it applies to OAs using active fibres (optical fibre amplifiers@ OFAs) containing rare-earth dopants@ such as erbium doped fibre amplifiers (EDFAs)@ presently commercially available@ as indicated in IEC 61291-1. This document provides the general background for optical amplifier gain transients and their measurements and indicates those IEC standard test methods for accurate and reliable measurements of the following transient parameters: a) optical input power increase/decrease transient gain overshoot and transient net gain overshoot; b) optical input power increase/decrease transient gain undershoot and transient net gain undershoot; c) optical input power increase/decrease gain offset; d) optical input power increase/decrease transient gain response constant (settling time). These parameters have been included to provide a complete description of the transient behaviour of gain controlled OA. The parameters defined here are applicable if the amplifier is an OFA or an alternative type of OA.

Optical amplifiers - Test methods - Part 4-4: Gain transient parameters - Single channel optical amplifiers with gain control

IEC 61290-4-3:2018 光学放大器 试验方法 第4-3部分:功率瞬态参数 输出功率控制中的单通道光放大器

Optical amplifiers - Test methods - Part 4-3: Power transient parameters - Single channel optical amplifiers in output power control

JIS C 6122-4-3:2018 光放大器. 试验方法. 第4-3部分:功率瞬态参数输出功率控制中的单通道光放大器

Optical amplifiers -- Test methods -- Part 4-3: Power transient parameters -- Single channel optical amplifiers in output power control

IEC 61291-1:2018 光学放大器.第1部分:总规范

This part of IEC 61291 applies to all commercially available optical amplifiers (OAs) and optically amplified assemblies. It applies to OAs using optically pumped fibres (OFAs based either on rare-earth doped fibres or on the Raman effect), semiconductors (SOAs), and waveguides (POWAs). The object of this document is to establish uniform requirements for transmission, operation, reliability and environmental properties of OAs, and; to provide assistance to the purchaser in the selection of consistently high-quality OA products for his particular applications. Parameters specified for OAs are those characterizing the transmission, operation, reliability and environmental properties of the OA seen as a "black box" from a general point of view. In the sectional and detail specifications a subset of these parameters will be specified according to the type and application of the particular OA device or assembly.

Optical amplifiers - Part 1: Generic specification

DIN EN 61291-5-2:2017 光纤放大器.第5-2部分:合格鉴定规范.光纤放大器可靠性合格鉴定(IEC 61291-5-2-2017);德文版本EN 61291-5-2-2017

This part of IEC 61291 applies to optical amplifiers (OAs) and optically amplified, elementary sub-systems for terrestrial applications, using active fibres (optical fibre amplifiers (OFAs)) containing rare-earth dopants, which are commercially available. The black box approach is used in this document. The black box approach is adopted in order to give product specifications which are independent of OA implementation details. For reliability qualification purposes, some information about the internal components is needed; these internal parts are themselves treated as black boxes. This standard gives requirements for the evaluation of OA reliability by combining the reliability of such internal black boxes. The object of this document is to specify the minimum list of reliability qualification tests, requirements on failure criteria during testing and on reliability predictions, and give the relevant normative references to establish a standard method for the assessment of the reliability of OFA devices and sub-systems in order to minimize risks and to promote product development and reliability qualification.

Optical amplifiers - Part 5-2: Qualification specifications - Reliability qualification for optical fibre amplifiers (IEC 61291-5-2:2017); German version EN 61291-5-2:2017

BS EN 61291-5-2:2017 光放大器.合格评定规范.光纤放大器可靠性合格评定

Optical amplifiers. Qualification specifications. Reliability qualification for optical fibre amplifiers

EN 61291-5-2:2017 光学放大器.第5-2部分:合格鉴定规范.光纤放大器的可靠性合格鉴定

IEC 61291-5-2:2017(E) applies to optical amplifiers (OAs) and optically amplified, elementary sub-systems for terrestrial applications, using active fibres (optical fibre amplifiers (OFAs)) containing rare-earth dopants, which are commercially available. The black box approach is used in this document. The black box approach is adopted in order to give product specifications which are independent of OA implementation details. For reliability qualification purposes, some information about the internal components is needed; these internal parts are themselves treated as black boxes. This document gives requirements for the evaluation of OA reliability by combining the reliability of such internal black boxes. The object of this document is to specify the minimum list of reliability qualification tests, requirements on failure criteria during testing and on reliability predictions, and give the relevant normative references to establish a standard method for the assessment of the reliability of OFA devices and sub-systems in order to minimize risks and to promote product development and reliability qualification. This second edition cancels and replaces the first edition published in 2002. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) removal of the contents on the relating quality management system from scope, terms and definitions, and the reliability requirements; b) moving fit-rate calculation to Annex B (informative); c) change of requirements for shock test; d) amendment of abbreviations related to changes a) and b). Keywords: optical amplifiers (OAs), optical fibre amplifiers (OFAs)

Optical amplifiers - Part 5-2: Qualification specifications - Reliability qualification for optical fibre amplifiers

DIN EN 61290-4-1:2017 光学放大器.试验方法.第4-1部分:瞬态增益参数.双波长法(IEC 61290-4-1-2016);德文版本EN 61290-4-1-2016

Optical amplifiers - Test methods - Part 4-1: Gain transient parameters - Two-wavelength method (IEC 61290-4-1:2016); German version EN 61290-4-1:2016

DIN EN 62343-3-2:2017 动态模块.第3-2部分:性能规格模板.光通道监测仪(IEC 62343-3-2-2016);德文版本EN 62343-3-2-2016

Dynamic modules - Part 3-2: Performance specification templates - Optical channel monitor (IEC 62343-3-2:2016); German version EN 62343-3-2:2016

DIN EN 62343-1:2017 动态模块.第1部分:性能标准.一般条件(IEC 62343-1-2016);德文版本EN 62343-1-2016

Dynamic modules - Part 1: Performance standards - General conditions (IEC 62343-1:2016); German version EN 62343-1:2016