标准-分析测试百科网

ISO 6623:2013 内燃机.活塞环.铸铁制刮环

This International Standard specifies the essential dimensional features of scraper rings made of cast iron, types N, NM, E, and EM, having diameters from 30 mm up to and including 200 mm, used in reciprocating internal combustion engines for road vehicles and other applications.

Internal combustion engines.Piston rings.Scraper rings made of cast iron

ICS: 43.060.10
CCS: J92
发布: 2013-07
实施

SAE J1240-2013 飞轮旋转试验规程

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of spark ignition and diesel type. Engine sizes are those capable of using SAE No. 6 through SAE No. 00 size flywheel housings. This document is intended to provide a uniform test procedure for flywheel assemblies to determine the rotative speeds at which they will either burst or withstand a s

Flywheel Spin Test Procedure

ICS: 43.060.10
CCS: T12
发布: 2013-05-03
实施: 2013-09-13

SAE J1456-2012 内燃机飞轮的最大允许转速

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of the spark ignition and diesel type equipped with a governor or speed limiting device. Engine sizes are those capable of using sAE No. 6 through SAE No. 00 flywheel housings. This document applies to methods used to determine the rotational speed capability of flywheels for stresses imposed by

Maximum Allowable Rotational Speed for Internal Combustion engine flywheels

ICS: 43.060.10
CCS
发布: 2012-10-24
实施: 2013-09-13

SAE J1172-2012 带密封法兰的发动机飞轮轴承箱

Engine Flywheel Housings with Sealed Flanges

ICS: 43.060.10
CCS: T12
发布: 2012-10-24
实施: 2013-09-13

SAE J620-2012 与装配驱动环型偏心自锁离合器的工业动力输出装置和装在发动机上的船用齿轮以及单轴承安装在发动机上的发电机一起使用的工业发动机飞轮

Flywheels for Industrial Engines Used with Industrial Power take-Offs Equipped with Driving-Ring Type Overcenter Clutches and engine-Mounted Marine Gears and Single Bearing Engine-Mounted power Generators

ICS: 43.060.10
CCS: T12
发布: 2012-10-24
实施: 2013-09-13

SAE J1240-2012 飞轮旋转试验规程

This SAE Recommended Practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of spark ignition and diesel type. Engine sizes are those capable of using SAE No. 6 through SAE No. 00 size flywheel housings. Purpose This document is intended to provide a uniform test procedure for flywheel assemblies to determine the rotative speeds at which they will either burst or withstand a specified limiting speed.

Flywheel Spin Test Procedure

ICS: 43.060.10
CCS: T12
发布: 2012-10-08
实施: 2012-10-09

SAE J927-2012 发动机装用变矩器飞轮

Flywheels for Engine-Mounted Torque Converters (Stabilized Type)

ICS: 43.060.10
CCS: T12
发布: 2012-06-11
实施: 2013-09-13

SAE J1033-2012 飞轮,飞轮外壳和飞轮外壳连接物的钻孔和端面跳动测量规程

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice applies to any internal combustion engine which can utilize SAE No. 6 thru SAE No. 00 size flywheel housing. It provides instructions for correcting flywheel housing bore runout readings which are influenced by crankshaft bearing clearance. Limits for bore and face runout are specified in the various SAE standards and recommended Practices covering flywheels and flywheel housings.

Procedure for Measuring Bore and Face Runout of Flywheels, flywheel housings and Flywheel Housing Adapters

ICS: 43.060.10
CCS: T12
发布: 2012-06-01
实施: 2013-09-13

SAE J617-2012 发动机飞轮壳和配套变速箱壳法兰

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face of the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded.

Engine Flywheel Housing and Mating Transmission Housing flanges