43.160 特种车辆 标准查询与下载

BS EN 17106-3-1:2021 道路作业机械 安全冬季服务机器 带旋转工具的清雪机和雪犁的要求

Road operation machinery. Safety. Winter service machines. Requirements for snow clearing machines with rotating tools and snow ploughs

T/SZZL 004-2021 活体畜禽厢式运输车

4.1　总则 4.1.1　畜禽车应符合本文件的规定，并按规定程序批准的产品图样和技术文件制造。 4.1.2　所用的外购件、外协件应符合相关标准的规定，并有制造厂的合格证明，经整车厂检验合格后方能使用。所有自制零部件、总成件经检验合格后方可装配使用。 4.2　整车 4.2.1　畜禽车的外廓尺寸、轴荷及质量限值应符合GB 1589的规定。 4.2.2　畜禽车安全要求应符合GB 7258的规定。 4.2.3　畜禽车制动性能应符合GB 12676和GB 7258的规定。 4.2.4　畜禽车侧倾稳定角应符合GB 7258的规定。 4.2.5　畜禽车的外部照明及光信号装置的安装要求应符合GB 4785的规定。车身反光标识和车辆尾部标志板应符合GB 7258的规定。 4.2.6　畜禽车应设置符合GB 11567规定的侧面和后下部防护装置。 4.2.7　畜禽半挂车应符合GB/T 23336的规定。 4.2.8　畜禽车的焊接应符合JB/T 5943的规定。 4.2.9　畜禽车所有外露黑色金属表面均应进行防腐蚀处理。涂镀层和化学处理层应符合QC/T 625的规定。油漆涂层应符合QC/T 484的规定。 4.2.10　畜禽车各连接件连接应牢固、可靠，不得松脱。螺纹紧固件的螺纹紧固扭矩应符合QC/T 518的规定。 4.2.11　畜禽车各运动机构应动作平稳、灵活、可靠，不应有相互干涉、卡滞和冲撞现象。 4.2.12　畜禽车的电气线路、气路、水路、液压管路布置应合理、整齐、美观，夹持牢固，不应与运动部件发生摩擦和干涉。油、气、水管路不得有渗漏现象。 4.2.13　畜禽车应配置净水箱和污物废液收集箱，污物废液收集箱收集的污物废液不得外溢；污物废液收集箱的排污管道应能排净污物废液收集箱的污物废液并能接入市政排污管网；净水箱和污物废液收集箱应密封良好，不得有渗漏现象。 4.2.14　畜禽车应配备饮水设施、设置补水接口。 4.2.15　畜禽车车厢应设置通风装置和温控装置，以满足GB/T 20014.11的要求。 4.2.16　畜禽车应设有安全装置，以防止装卸时导致畜禽掉落。 4.3　车厢 4.3.1　畜禽车车厢结构应为封闭式。 4.3.2　畜禽车车厢宜采用铝合金材料或不锈钢材料制造。 4.3.3　畜禽车车厢外表面应光滑平整，无明显的凹凸和锤痕。 4.3.4　畜禽车车厢内可根据装运畜禽的品种分成多层，车厢底板、上层地板应防滑，上层地板应密封良好，畜禽排泄物不得渗漏。 4.3.5　畜禽车上层地板可根据畜禽大小设定不同高度，上层地板应坚固，应有足够的强度。 4.3.6　畜禽车车厢内隔层净高度应满足GB/T 20014.11的要求。 4.3.7　畜禽车车厢应设置围栏和隔离设施，围栏长度和隔离设施高度应满足GB/T 20014.11的要求。 4.3.8　畜禽车车厢应设置检查口和观察口。 4.3.9　畜禽车车厢应装备安全系挂装置。 4.3.10　畜禽车车厢厢顶应防水、坚固、隔热保温。 4.3.11　畜禽车车厢厢体应隔热，厢内宜配备照明设备。 4.3.12　畜禽车车厢底部应密封良好。 4.3.13　畜禽车车厢门应开关灵活，锁止可靠，在行驶过程中不得自动开启。 4.3.14　畜禽车车厢与底盘连接应牢固可靠，在行驶过程中车厢与底盘之间不得发生相对运动。 4.3.15　畜禽车车厢应方便人员上下车及畜禽装卸。 4.3.16　畜禽车车厢后部用于装卸用的尾板应符合QC/T 699的规定。 4.3.17　尾板的选型、设计、安装应符合GB/T 37706的规定，并可靠保证安全使用。 4.4　液压系统 4.4.1　液压系统应符合GB/T 3766的规定，在1.25倍额定工作压力下保持5min系统零部件不得损坏变形和渗漏。 4.4.2　液压元件应符合GB/T 7935的规定。 4.4.3　平衡阀和液压锁与执行机构的连接应是刚性连接。 4.4.4　液压系统应设置安全阀，其调整压力应不大于系统额定工作压力的110%。 4.4.5　液压油固体污染度应符合QC/T 29104的规定，其固体污染颗粒数代码为21/18。 4.4.6　液压系统应保证散热的要求，工作时油箱内液压油温度应不超过80℃。 4.5　运送生猪的车辆要求 4.5.1　车厢内应装备喷淋系统，喷水应呈雾状，喷水覆盖率应大于等于80%（包括上层地板）。 4.5.2　车厢内每层应设置观察厢内动态的视频监控装置。 4.5.3　车辆应装备符合GB/T 19056要求的汽车行驶记录仪。

Live stock van

BS EN 17106-3-2:2021 道路作业机械 安全冬季服务机器 摊铺机的具体要求

Road operation machinery. Safety. Winter service machines. Specific requirements for spreading machines

BS EN 17106-4:2021 道路作业机械 安全道路服务区维护机器 割草机和割草机的要求

Road operation machinery. Safety. Road service area maintenance machines. Requirements for grass and brush cutting machines

BS EN 17106-2:2021 道路作业机械 安全路面清洁机的具体要求

Road operation machinery. Safety. Specific requirements for road surface cleaning machines

ASTM D6336-11(2021) 用真空改良Sigma叶片混合器评价颜料润湿冲洗剂的标准实施规程

1.1 This practice covers guidelines for the evaluations of flushing vehicles for pigment dispersion using a vacuum modified sigma blade mixer, or vacuum flusher. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Evaluation of Flushing Vehicles for Pigment Wetting Using a Vacuum Modified Sigma Blade Mixer

DS/EN 17106-1:2021 道路作业机械《安全》第1部分：一般要求

Road operation machinery – Safety – Part 1: General requirements

DS/EN 17106-2:2021 道路作业机械《安全》第2部分：路面清扫机的具体要求

Road operation machinery – Safety – Part 2: Specific requirements for road surface cleaning machines

DS/EN 17106-3-2:2021 道路作业机械《安全》第 3-2 部分：冬季作业机械《撒布机的特殊要求》

Road operation machinery – Safety – Part 3-2: Winter service machines – Specific requirements for spreading machines

DS/EN 17106-3-1:2021 道路作业机械《安全》第 3-1 部分：冬季作业机械《带旋转工具和扫雪机的清雪机械要求》

Road operation machinery – Safety – Part 3-1: Winter service machines – Requirements for snow clearing machines with rotating tools and snow ploughs

DS/EN 17106-4:2021 道路作业机械《安全》第4部分：道路服务区维护机械《割草机和灌木切割机的要求》

Road operation machinery – Safety – Part 4: Road service area maintenance machines – Requirements for grass and brush cutting machines

EN 17106-2:2021 道路作业机械 安全 第2部分：路面清洁机的特殊要求

This document together with EN 17106 1:2021 deals with all significant hazards, hazardous situations and events relevant to road surface cleaning machines (as defined in EN 15429 1:2007 and EN 17106 1:2021, 3.7) when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex B) associated with the whole lifetime of the machine as described in EN ISO 12100:2010, 5.4. The requirements of this document are complementary to the common requirements formulated in EN 17106 1:2021. This document does not repeat the requirements from EN 17106 1:2021 but supplements or modifies the requirements for road surface cleaning machines. This document is not applicable to road surface cleaning machines manufactured before the date of its publication.

Road operation machinery - Safety - Part 2: Specific requirements for road surface cleaning machines

EN 17106-4:2021 道路作业机械 安全 第4部分：道路服务区维护机械 割草机和灌木切割机的要求

This European Standard applies to machines used for road service area maintenance which are attached to or mounted on carrier vehicles (e.g. tractor, truck), or which are self-propelled machinery and which are defined in Clause 3. Directives and standards for the vehicular truck or tractor chassis aspect, termed 'carrier vehicle' in this standard, would be those relevant to that equipment. For machinery which are a combination of a grass/brush-cutting attachment and a carrier-vehicle, this part of the standard applies to the grass or brush cutting attachment itself and with all health and safety requirements of the interaction and effects between attachment and the carrier vehicle when used together (e.g. stability, visibility). For self-propelled machinery, this part only deals with health and safety requirements of the attachment itself and does not deal with the self-propelled machinery itself which are dealt with in EN 17106 1. NOTE 1 Road regulations or Directive apply to vehicular truck and tractor. NOTE 2 The use in public road traffic is governed by the national regulations. This European Standard deals with all significant hazards identified through a risk assessment pertinent to road service area maintenance machines, when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). This European Standard does not deal with significant hazards associated with EMC. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards associated with machine operation, setting and adjustments, load discharge and routine maintenance. This European Standard does not include requirements for the carrier vehicles (e.g. trucks, tractors, construction machines, industrial trucks). These are covered in directives related to the construction of vehicles. This European Standard does not deal with: — walker-operated and hand-held machines; — machines for the maintenance of sports grounds; — machines for agriculture, horticulture and forestry; — pit and sewer cleaning vehicles/-machines; — grass and brush cutting machines with multiple cutting heads (see Annex A, Clause C.2, Figure C.20) — vertical axis grass and brush cutting machines except inter-post machinery (see Annex A, Clause C.2, Figure C.22) — horizontal axis grass and brush cutting machines with two rotors (see Annex A, Clause C.2, Figure C.23) — self-propelled remote controlled machinery for road service area maintenance, except the mowing head — self-propelled remote controlled machinery used for forestry application (see Annex A, Clause C.2, Figure C.21) — cleansing and ditch maintenance machines (see Annex A, Clause C.2, Figure C.24 and C.25) A machine which is a combination of several parts with different uses should conform to all the standards referring to the corresponding parts of the machine. This document, together with part 1, deals with all significant hazards for road service area maintenance machines – grass and brush cutting machines when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer associated with the whole life time of the machine (see Clause 4). The requirements of this part are complementary to the common requirements formulated in prEN 17106 1:2017. This document does not repeat the requirements from prEN 17106 1:2017, but adds or replaces the requirements for application for grass and brush cutting machines. This European Standard does not deal with the risks associated with the operation of machines in potentially explosive atmospheres. This standard applies to machines manufactured after the date of approval of this standard through CEN.

Road operation machinery - Safety - Part 4: Road service area maintenance machines - Requirements for grass and brush cutting machines

EN 17106-3-1:2021 道路作业机械 安全 第 3-1 部分：冬季服务机械 带旋转工具和扫雪机的清雪机的要求

This document together with EN 17106 1:2021 deals with all significant hazards, hazardous situations and events relevant to winter service machines – snow clearing machines with rotating tools and snow ploughs when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A) associated with the whole lifetime of the machine as described in EN ISO 12100:2010, 5.4. The requirements of this document are complementary to the common requirements formulated in EN 17106 1:2021. This document does not repeat the requirements from EN 17106 1:2021 but supplements or modifies the requirements for winter service machines – snow clearing machines with rotating tools and snow ploughs. This document is not applicable to snow clearing machines with rotating tools and snow ploughs manufactured before the date of its publication.

Road operation machinery - Safety - Part 3-1: Winter service machines - Requirements for snow clearing machines with rotating tools and snow ploughs

EN 17106-3-2:2021 道路作业机械 安全 第 3-2 部分：冬季服务机械 摊铺机的特殊要求

This document together with EN 17106 1:2021 deals with all significant hazards, hazardous situations and events relevant to winter service machines – spreading machines when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A) associated with the whole lifetime of the machine as described in EN ISO 12100:2010, 5.4. The requirements of this document are complementary to the common requirements formulated in EN 17106 1:2021. This document does not repeat the requirements from EN 17106 1:2021 but supplements or modifies the requirements for winter service machines – spreading machines. This document is not applicable to spreading machines manufactured before the date of its publication.

Road operation machinery - Safety - Part 3-2: Winter service machines - Specific requirements for spreading machines

T/STACAES 020-2021 环卫垃圾收运车辆 吸粪车

1.规定了吸粪车的技术要求。包括：一般要求、安全要求、专项要求和纯电动吸粪车电安全要求。 2.规定了吸粪车的试验方法。包括：作业噪声测量、系统最大真空度测量、罐体有效容积测量、抽吸时间测量、防溢流装置试验、除臭性能试验、清水箱容积测量、可靠性试验和纯电动吸粪车电安全试验。 3.规定了吸粪车的检验规则。包括出厂检验和型式检验。 4.规定了标志、使用说明书、随车文件、运输和贮存的要求。

Waste collection and transport vehicles for sanitation Suction-type excrement tanker

T/STACAES 014-2021 环卫垃圾收运车辆 车厢可卸式垃圾车

1.规定了车厢可卸式垃圾车的技术要求（包括：一般要求、安全要求、专项要求和纯电动车厢可卸式垃圾车电安全要求）。 2.规定了车厢可卸式垃圾车的试验方法（包括：作业噪声测量、装箱、卸料和卸箱作业时间测量、可靠性试验和纯电动车厢可卸式垃圾车电安全试验）。 3.规定了车厢可卸式垃圾车的检验规则。 4.规定了标志和使用说明书和随车文件、运输和贮存的要求。

Waste collection and transport vehicles for sanitation Detachable cotainer garbage collector

T/STACAES 017-2021 环卫垃圾收运车辆 自卸式垃圾车

1.规定了自卸式垃圾车的技术要求。包括：一般要求、安全要求、专项要求和纯电动自卸式垃圾车电安全要求。 2.规定了自卸式垃圾车的试验方法。包括：作业噪声测量、车厢举升下降时间和厢盖启闭时间测量、结合面间隙测量、可靠性试验和纯电动自卸式垃圾车电安全试验。 3.规定了自卸式垃圾车的检验规则。包括出厂检验和型式检验。 4.规定了标志、使用说明书、随车文件、运输和贮存的要求。

Waste collection and transport vehicles for sanitation Garbage dump truck

T/STACAES 013-2021 环卫垃圾收运车辆 压缩式垃圾车

1.规定了压缩式垃圾车的技术要求包括一般要求、安全要求、专项要求和纯电动压缩式垃圾车电安全要求。 2.规定了试验方法（常规试验、专业性试验）要求和相关指标值。 3.规定了检验规则。 4.标志、使用说明书和随车文件、运输和贮存相关要求。

Waste collection and transport vehicles for sanitation Compression refuse collector

T/STACAES 015-2021 环卫垃圾收运车辆 自装卸式垃圾车

1.规定了自卸式垃圾车的技术要求。包括：一般要求、安全要求、专项要求和纯电动自卸式垃圾车电安全要求。 2.规定了自卸式垃圾车的试验方法。包括：作业噪声测量、车厢举升下降时间和厢盖启闭时间测量、结合面间隙测量、可靠性试验和纯电动自卸式垃圾车电安全试验。 3.规定了自卸式垃圾车的检验规则。包括出厂检验和型式检验。 4.规定了标志、使用说明书、随车文件、运输和贮存的要求。

Waste collection and transport vehicles for sanitation Self-loading Garbage truck