45.060.20 车辆 标准查询与下载

T/ZZB 3075-2023 铁道重载货车用干摩擦式缓冲器箱体

本文件规定了铁道重载货车用干摩擦式缓冲器箱体的术语与定义、基本要求、技术要求、试验方法、 检验规则、产品标志、包装、运输和贮存及质量承诺。  本文件适用于铁道重载货车用干摩擦式缓冲器箱体。

Dry friction draft gear housing for heavy haul freight of railway rolling stock

TB/T 3582-2023 动车组应急通风系统

EMU emergency ventilation system

TB/T 3338.2-2023 铁路客车及动车组卫生间 第2部分：集便装置

Railway passenger cars and EMU toilets Part 2: toilet collection devices

23/30462745 DC BS EN 15839 铁路应用 铁路车辆运行特性验收测试与仿真 纵向压力下的运行安全

BS EN 15839. Railway applications. Testing and simulation for the acceptance of running characteristics of railway vehicles. Running safety under longitudinal compressive forces

T/CCTAS 49-2023 城市轨道交通车辆安全评估规范

本文件规定了城市轨道交通车辆投入运营前开展安全评估的通用要求、评估机构的要求、相关方职责、各阶段评估内容和评估交付物。

Specification of safety assessment for urban rail vehicles

T/CAMET 07009-2023 储能式有轨电车地面充电装置通用技术规范

本文件规定了储能式有轨电车地面充电装置（以下简称“充电装置”）的术语和定义、充电装置分类及组成、环境条件、供电条件、技术要求、试验方法、检验规则，标志、包装、运输与贮存等内容。 本文件适用于为采用车载储能电源作为动力源的有轨电车充电用的储能式有轨电车地面充电装置的设计、产品生产（制造）、供需双方贸易、检验检测活动等。

General technical specifications for ground charging devices for energy storage trams

CAN/CGSB-43.147-2023 铁路危险货物运输集装箱

1 Scope 1.1 Organization and content This standard applies to the design, manufacture, maintenance, qualification, inspection and marking of tank cars and the selection and use of large means of containment or transport units used in the handling, offering for transport or transporting of dangerous goods by rail of classes 2, 3, 4, 5, 8, 9 and division 6.1. This standard does not apply to large means of containment that are used exclusively for non-dangerous goods. This standard consists of eight main sets of requirements and five annexes. Sections 1 through 3 specify the general scope, normative references and terms and definitions. Section 4 sets out general requirements and defines the applicability of the standard and the precedence of each section. Section 5 sets out the quality management system requirements and its applicability. Section 6 outlines the registration requirements applicable to facilities performing manufacture, inspection, maintenance or qualification of tank cars. Sections 7 and 8 set out tank car marking requirements and tank car manufacturer and modification requirements. Section 9 sets out the requirements for the periodic qualification and maintenance of tank cars. Section 10 covers the selection and use requirements for containers. Section 11 provides some allowances for one time low risk movement of non-conforming containers. Annexes A and B (normative) specify procedures and set out acceptance criteria for the side and head impact test for TC 117P tank cars. Annex C (normative) specifies a procedure to test tank car head puncture resistance systems. Annex D (normative) specifies test procedures and sets out acceptance criteria for simulated pool-fire and torch-fire. Annex E (normative) sets out, in schedule 1, the requirements applicable to special provisions 1 to 81, and in schedule 2, lists dangerous goods and specifies the special provisions that are applicable to each of the listed dangerous goods. 1.2 Minimum requirements This standard sets out certain minimum requirements regarding the design, manufacture, qualification, selection and use, or testing of containers. It is essential to exercise competent technical, engineering and safety judgment in conjunction with this standard. 1.3 Additional requirements 1.3.1 Conflict The Transportation of Dangerous Goods Act, 1992 (TDG Act) and the Transportation of Dangerous Goods Regulations (TDG Regulations) may set out additional requirements regarding the design, construction, qualification, selection, and use, or testing of containers. Where there is an inconsistency between the requirements of this standard and those of the TDG Act or TDG Regulations, the TDG Act or TDG Regulations prevail to the extent of the inconsistency. It is recommended to read the standard in conjunction with the TDG Regulations. 1.3.2 Safety The testing and evaluation of a product against this standard may require the use of materials and/or equipment that could be hazardous. This standard does not purport to address all the safety aspects associated with its use. Anyone using this standard has the responsibility to consult the appropriate authorities and to establish appropriate health and safety practices in conjunction with any applicable regulatory requirements prior to its use. 1.3.3 Units of measurement Quantities and dimensions used in this standard are provided in units from the International System of Units (SI units). Imperial equivalents may be shown in brackets, as applicable.

Containers for transport of dangerous goods by rail

23/30447482 DC BS EN 16286-1 铁路应用 车辆之间的通道系统 第 1 部分：主要应用

BS EN 16286-1. Railway applications. Gangway systems between vehicles - Part 1. Main applications

T/CCTAS 42-2022 储能式自动导向胶轮电车车辆技术条件

本文件规定了储能式自动导向胶轮电车车辆的使用条件、车辆主要技术规格、一般规定、车体及内装设备、车载储能系统、电气系统、制动系统、安全设施、通信与乘客信息系统。

Technical specification for automated guided rubber-tyre tram with energy storage system

22/30393016 DC BS EN 12299 铁路应用 为乘客带来乘坐舒适感 测量与评估

BS EN 12299. Railway applications. Ride comfort for passengers. Measurement and evaluation

T/TRVA 00003-2022 制动管路用薄壁不锈钢管通用技术规范

本文件规定了制动管路用薄壁不锈钢管的技术要求、检验方法、检验规则等。 本文件适用于轨道车辆制动管路系统，其它系统用不锈钢管可参照执行。

General technical specification for thin-walled stainless steel pipes for brake lines

T/TRVA 00002-2022 塑木型材木骨技术规范

本文件规定了塑木型材木骨的开发、生产和供货的总体技术要求。 本文件适用于动车组，其他轨道车辆可参考使用。

Technical specification for wood frame of plastic wood profile

T/TRVA 00001-2022 动车组用管接件设计技术规范

本文件规定了动车组用管接件的型式与尺寸、技术要求、试验方法、检验规则、包装、运输及储存等。 本文件适用于动车组用管接件的设计、制造和检验。对于特殊用途和使用条件的管接件供需双方另行商定。

Technical specifications for design of pipe fittings for EMUs

T/TRVA 00004-2022 时速160公里动力集中电动车组电控塞拉门技术条件

本文件规定了时速160公里动力集中电动车组电控塞拉门的术语和定义、使用条件、产品分类、组成及标识、技术要求、检验方法、检验规则、包装、标志、运输、储存。 本文件适用于时速160公里动力集中电动车组，其他动车组或机车车辆可参照执行。

Technical conditions for electronically controlled sliding doors of 160km/h centralized power EMUs

T/TRVA 00009-2022 中低速客车用制动盘技术规范

本文件规定了铁路客车用制动盘的技术要求、检验方法、检验规则、标志、包装、运输与存储、合格证。 本文件适用于运用速度不大于160Km/h、轴重不大于18t的客车用轴装制动盘的设计与制造，其他车型可参考采用。

Technical specifications for brake discs for medium and low speed passenger cars

T/CAMET 08012-2022 中低速磁浮交通车辆悬浮供电系统技术规范

本文件规定了中低速磁浮交通车辆悬浮供电系统的使用条件、系统技术要求、部件技术要求、试验方法、检验规则。 本文件适用于中低速磁浮交通车辆悬浮供电系统的设计、制造和检验。

Technical specifications of power supply system for levitating of medium-low speed maglev vehicle

22/30448015 DC BS EN 15877-1 铁路应用 铁路车辆的标记 第 1 部分：货车

BS EN 15877-1. Railway applications. Markings of railway vehicles. - Part 1. Freight wagons

BS EN 16116-1:2022 铁路应用程序 台阶、扶手和员工相关通道的设计要求 客车、货车和机车

1   Scope This document specifies the minimum ergonomic and structural integrity requirements for steps and handrails used by staff to access the following heavy rail vehicles: — passenger vehicles; — vans; — locomotives; — power units of rolling stock; — passenger-rated car carriers. This document defines the required spaces necessary for shunter handrails and shunter ’s stand and gives references for the required spaces necessary for handling of screw couplings with side buffers. For staff access, it defines footsteps, handrails and their dimensions and free spaces. To fulfil the requirements for loads which are applied by the staff, it defines dimensions and requirements for materials or design loads. This document also defines the general requirements of steps and handrail for access to external equipment, for example windscreens, wipers or external lights.

Railway applications. Design requirements for steps, handrails and associated access for staff. Passenger vehicles, vans and locomotives

22/30447479 DC BS EN 16286-2 铁路应用 车辆之间的通道系统 第 2 部分：声学测量

BS EN 16286-2. Railway applications. Gangway systems between vehicles - Part 2. Acoustic measurements

22/30448012 DC BS EN 16116-2 铁路应用 台阶、扶手和相关员工通道的设计要求 第 2 部分：货车

BS EN 16116-2. Railway applications. Design requirements for steps, handrails and associated access for staff - Part 2. Freight wagons