47.020.40 起重设备和货物搬运设备 标准查询与下载
共找到 452 条与 起重设备和货物搬运设备 相关的标准，共 31 页
Cast steel pawl type chain cable stoppers for grade 2 chain cable
- ICS
- 47.020.40
- CCS
- 发布
- 20131202
- 实施
- 20131202
Cast iron deck end rollers(small size)
- ICS
- 47.020.40
- CCS
- 发布
- 20131202
- 实施
- 20131202
Cast iron dog type chain cable compressors
- ICS
- 47.020.40
- CCS
- 发布
- 2013-12-02
- 实施
Steel plate deck end rollers(small size)
- ICS
- 47.020.40
- CCS
- 发布
- 2013-12-02
- 实施
本标准规定了船用液压臂架起重机(以下简称起重机)工厂试验的一般规定、水平台架试验、倾斜台架试验、温升试验和水密防水试验。本标准适用于普通船用起重机的工厂试验。有特殊要求或特殊结构的起重机,可按订货协议所规定的要求进行。
Works trial method for marine hydraulic jib-crane
- ICS
- 47.020.40
- CCS
- U22
- 发布
- 2013-07-22
- 实施
- 2013-12-01
本标准规定了船用克令吊(以下简称克令吊)的术语和定义、产品种类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于由电动或电-液驱动的安装在船上用于在港口条件下装卸货物的起重机的设计、生产和验收。本标准不适用于电磁起重机、海洋平台起重机、浮式起重机以及其他起重机。
Deck crane
- ICS
- 47.020.40
- CCS
- U22
- 发布
- 2013-07-22
- 实施
- 2013-12-01
本标准规定了船用臂架起重机的涂装技术要求。本标准适用于船用臂架起重机涂装设计、制造和验收,对其他船用甲板机械涂装,亦可参照采用。
Painting technical requirement on deck crane
- ICS
- 47.020.40
- CCS
- U24
- 发布
- 2013-07-22
- 实施
- 2013-12-01
本标准规定了往复柱塞式液压舵机部件及整机的装配要求。本标准适用于海洋船舶和内河船舶往复柱塞式液压舵机的装配。
Specification for assemble of reciprocal ram type hydraulic steering gear
- ICS
- 47.020.40
- CCS
- U22
- 发布
- 2013-07-22
- 实施
- 2013-12-01
本标准规定了起锚绞车的分类与标记、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于安装于船艉的液压、电动起锚绞车的设计、制造和验收。工程船用起锚绞车也可参照使用。
Anchor winches
- ICS
- 47.020.40
- CCS
- U21
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了锚链轮的齿形基本尺寸及要求。本标准适用于起锚机及起锚绞盘使用的锚链轮。本标准规定的锚链轮适用于GB/T 549 “电焊锚链”中的有档锚链。
Cable lifter
- ICS
- 47.020.40
- CCS
- U22
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了船用起重机回转支承(以下简称回转支承)的符号、分类和标记、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于环境温度不低于-40 ℃的船用起重机和近海起重机用回转支承的设计、制造和验收。
Slewing bearing for crane of ship
- ICS
- 47.020.40
- CCS
- U22
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了转叶式舵机(以下简称舵机)部件、整机及配套泵站的制造单位装配要求。本标准适用于海洋船舶和内河船舶舵机及配套液压泵站的制造。
Specification for assembly of rotary vane steering gear
- ICS
- 47.020.40
- CCS
- U22
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了索具螺旋扣(简称螺旋扣)的分类和标记、要求、试验方法、检验规则、标志、包装、贮存和运输。本标准适用于船上起重部件、救生艇架、绑扎紧固用的螺旋扣的设计、制造和验收。
Turnbuckle for rigging
- ICS
- 47.020.40
- CCS
- U24
- 发布
- 2013-04-25
- 实施
- 2013-09-01
Abstract Lays down requirements for design, installation and inspection. It is necessary to ensure compliance with such statutory requirements, rules and regulations as may be applicable to any individual ship as well as with lift safety codes.
Lifts on ships -- Specific requirements
- ICS
- 47.020.40
- CCS
- 发布
- 2013-04-01
- 实施
1.1 This guide covers the selection of containment boom that may be used to control spills of oil and other substances that float on a body of water. 1.2 This guide does not address the compatibility of spill control equipment with spill products. It is the user’s responsibility to ensure than any equipment selected is compatible with anticipated products. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Guide for Selection of Booms in Accordance With Water Body Classifications
- ICS
- 47.020.40
- CCS
- 发布
- 2013-04-01
- 实施
Ships and marine technology.Marine general purpose chains.Specification
- ICS
- 47.020.40
- CCS
- U22
- 发布
- 2013-02-08
- 实施
