47.020.99 有关造船和海上构筑物的其他标准 标准查询与下载

T/CANSI 18-2020 双燃料船舶双壁管设计、制作及安装要求

本标准规定了双燃料船舶的双壁管设计、制作和安装要求。

Design, fabrication and installation requirements of double wall pipe for dual fuel ship

ASTM F1323-14(2020) 船用焚烧炉标准规范

1.1 This specification covers the design, manufacture, performance, operation, functioning, and testing of incinerators intended to incinerate garbage and other shipboard wastes generated during the ship’s normal service (that is, maintenance, operational, domestic, and cargo-associated wastes). 1.2 This specification is a companion document to Guide F1322. 1.3 This specification applies to those incinerator plants with capacities up to 4000 kW per unit. 1.4 Additional information is given in Appendix X1 – Appendix X8. 1.5 This specification does not apply to systems on special incinerator ships, for example, for burning industrial wastes such as chemicals, manufacturing residues, and so forth. 1.6 This specification does not address the electrical supply to the unit nor the foundation connections and stack connections. 1.7 It is possible that this standard will involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. If an incinerator is to be operated in coastal regions, the strictest governing regulations for those countries in which the incinerator would potentially operate would form the requirement basis. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Shipboard Incinerators

KS V ISO 11711-1-2019 船舶和航海技术 管道和机械 压载水取样和分析 第1部分：排放取样口

Ships and marine technology — Piping and machinery — Ballast water sampling and analysis — Part 1: Discharge sampling port

KS V ISO 16145-1-2019 船舶和航海技术 防护涂层和检验方法 第1部分：专用海水压载舱

Ships and marine technology — Protective coatings and inspection method — Part 1: Dedicated sea water ballast tanks

BS EN ISO 21593:2019 船舶和海洋技术 用于液化天然气加注的干式断开/连接联轴器的技术要求

What is ISO 21593 - Dry-disconnect/connect couplings for bunkering liquefied natural gas about?    ISO 21593 specifies the design, minimum safety, functional, and marking requirements, as well as the interface types and dimensions and testing procedures for dry-disconnect/connect couplings for LNG hose bunkering systems intended for use on LNG bunkering ships, tank trucks and shore-based facilities, and other bunkering infrastructures.   Note1: ISO 21593 is not applicable to hydraulically operated quick connect/disconnect couplers (QCDC) used for hard loading arms, which is covered in ISO 16904 .   Note2: Based on the technology used in industrial manufacturing at the time of development of ISO 21593 , it is applicable to sizes of couplings ranging from DN 25 to DN 200.  Who is ISO 21593 - Dry-disconnect/connect couplings for bunkering liquefied natural gas for?   ISO 21593 on dry-disconnect/connect couplings is useful for:  

Ship and marine technology, Technical requirements for dry-disconnect/connect couplings for bunkering liquefied natural gas

EN ISO 21593:2019 船舶和航海技术.液化天然气加料用干式断开/连接管接头的技术要求

This document specifies the design, minimum safety, functional and marking requirements, as well as the interface types and dimensions and testing procedures for dry-disconnect/connect couplings for LNG hose bunkering systems intended for use on LNG bunkering ships, tank trucks and shore-based facilities and other bunkering infrastructures. It is not applicable to hydraulically operated quick connect/disconnect couplers (QCDC) used for hard loading arms, which is covered in ISO 16904. Based on the technology used in industrial manufacturing at the time of development of this document, it is applicable to sizes of couplings ranging from DN 25 to DN 200.

Ship and marine technology - Technical requirements for dry-disconnect/connect couplings for bunkering liquefied natural gas (ISO 21593:2019)

ISO 21593:2019 船舶和航海技术.液化天然气加料用干式断开/连接管接头的技术要求

This document specifies the design, minimum safety, functional and marking requirements, as well as the interface types and dimensions and testing procedures for dry-disconnect/connect couplings for LNG hose bunkering systems intended for use on LNG bunkering ships, tank trucks and shore-based facilities and other bunkering infrastructures. It is not applicable to hydraulically operated quick connect/disconnect couplers (QCDC) used for hard loading arms, which is covered in ISO 16904. Based on the technology used in industrial manufacturing at the time of development of this document, it is applicable to sizes of couplings ranging from DN 25 to DN 200.

Ships and marine technology — Technical requirements for dry-disconnect/connect couplings for bunkering liquefied natural gas

ISO 15738:2019 船舶和海洋技术 - 充气救生设备的气体充气系统

This document specifies performance and testing requirements for gas inflation systems for inflatable life-saving appliances. NOTE It is suitable for inflatable life-saving appliances complying with the requirements of the 1974 Safety of Life at Sea Convention ISOLAS 74), as amended, and the IMO International Life-Saving Appliance Code (LSA Code) as amended, adopted by IMO Resolution MSC.48(66). This document applies to gas inflation systems which consist of an inflation gas, a gas cylinder valve, a gas cylinder operating head, high-pressure hoses, and pressure-relief/transfer, inflate/deflate and non- return valves. This document addresses only systems in which compressed inflation gas in cylinders is used as the inflation medium. National requirements for qualification, use, and testing of gas cylinders vary widely. Such requirements for gas cylinders are not addressed in this document, but it is presupposed that gas cylinders meet the requirements of the applicable regulatory bodies. The systems addressed in this document are of the type generally used in life-saving appliances, such as survival craft, marine evacuation systems, and means of rescue. Systems used in personal life-saving appliances, such as inflatable lifejackets, are addressed in ISO 12402-7.

Ships and marine technology — Maritime safety — Gas inflation systems for inflatable life-saving appliances

JT/T 1281-2019 近海潜水支持船选择技术要求

Technical requirements for offshore diving support vessel selection

BS ISO 11711-1:2019 船舶和海洋技术 水生公害物种 压载水排放采样口

What is ISO 11711-1 - Ballast water discharge sample port about?    ISO 11711-1 is the first part of the ISO 11711 series of standards that specifies requirements for the design and the fitting arrangements of ballast water discharge sample ports. In coordination with the vessel, a suitable sample collection probe is installed into the shipboard sample port as needed to collect ballast samples, and the port is sealed with a blind flange at other times.    ISO 11711-1 addresses the location of sample ports to accommodate representative sampling, and it standardizes the presentation of the port to accommodate various probe configurations. ISO 11711-1 provides specifications for a ret...

Ships and marine technology. Aquatic nuisance species. Ballast water discharge sample port

ISO 11711-1:2019 船舶和海洋技术.水生有害物种.第1部分:压载水排放取样港

This document specifies requirements for the design and the fitting arrangements of ballast water discharge sample ports. In coordination with the vessel, a suitable sample collection probe is installed into the shipboard sample port as needed to collect ballast samples, and the port is sealed with a blind flange at other times. This document addresses the location of sample ports to accommodate representative sampling, and it standardizes the presentation of the port to accommodate various probe configurations. It provides specifications for a return port to the ballast line downstream of the sample collection port, allowing processed sample water to be returned to the ballast pipe. The appropriate sample probe and other sample collection apparatus is determined by the sample collection team according to the requirements NOTE The distinction between the sample port discussed in this document and the sample probe discussed ballast piping to accept multiple sample probe configurations. The sample probe is a temporarily installed water collection pipe designed by the sampling party to mate with the sample port and to meet the measurement objectives of the sample. This document is applicable to ships with a ballast discharge pipe size of DN 100 or greater, with turbulent flows. Guidance for smaller ballast pipe diameters is given in Annex A. This document primarily addresses the collection of ballast water discharge samples. Optional requirements for installation of sample ports intended to collect uptake samples are provided in Annex B.

Ships and marine technology — Aquatic nuisance species — Part 1: Ballast water discharge sample port

CB/T 4491-2019 自升式钻井平台钻井设备的布置原则和方法

Principles and methods of layout of drilling equipment for jack-up drilling platform

JT/T 164.6-2019 绞吸挖泥船专用设备修理技术要求 第6部分：绞刀传动装置

JT/T164的本部分规定了绞吸挖泥船绞刀传动装置的勘验、修理、检验和交付文件的技术要求。 本部分适用于绞吸挖泥船绞刀传动装置的修理。

Technical requirements for repair of special equipment for cutter suction dredgers Part 6: Cutter drive

KS V ISO 19030-3-2019 船舶和船舶技术 - 船体和螺旋桨性能变化的测量 - 第3部分:替代方法

Ships and marine technology — Measurement of changes in hull and propeller performance — Part 3: Alternative methods

KS V ISO 19030-3:2019 船舶和船舶技术 - 船体和螺旋桨性能变化的测量 - 第3部分:替代方法

Ships and marine technology — Measurement of changes in hull and propeller performance — Part 3: Alternative methods

KS V ISO 19030-3-2019(2023) 船舶和海洋技术船体和螺旋桨性能变化的测量第3部分:替代方法

Ships and marine technology — Measurement of changes in hull and propeller performance — Part 3: Alternative methods

DIN 87374:2018 带传输管的遥控装置 焊入式甲板操作装置

This document specifies the design, sizes and materials for operating devices, welding-in type of Remonte control gears. Furthermore, statements are given on the terms of delivery and labeling.

Remote control gear with transmission tubing - Deck operating devices, welding-in type

DIN 87375:2018 带传输管的遥控装置 带可回转冠状齿轮装置的甲板操作装置，焊入式

This document specifies the design, sizes and materials of deck operating devices with slewable crown gear unit, welding-in type for remote control gears. Furthermore, statements are given on the terms of delivery and labeling.

Remote control gear with transmission tubing - Deck operating devices with slewable crown gear unit, welding-in type

DIN 87371:2018 带传输管的遥控装置 传输管支架

This document specifies the design, sizes and materials for holder for transmission tubing. Furthermore, statements are given on the terms of delivery and labeling.

Remote control gear with transmission tubing - Holder for transmission tubing

ISO 17325-3:2018 船舶和海洋技术.海洋环境保护.油栅.第3部分:端部连接器

This document specifies the requirements for the design of end connectors of oil booms used for the prevention of spreading of oil spills on water. These criteria are intended to define minimum mating characteristics and are not intended to be restricted to a specific configuration. It should be considered that different types of connectors are preferably used in different areas. This document does not define any priority. It remains the responsibility of manufacturers and users to select the right connector for the intended application. Stability features of boom connectors are the result of interaction between bodies of booms and connectors. This document does not purport to address all safety concerns, if any, associated with its use. However, it is the responsibility of the user of this document to establish the appropriate safety and health procedures, and to determine the applicability of regulatory limitations.

Ships and marine technology — Marine environment protection — Oil booms — Part 3: End connectors