49.025.40 橡胶和塑料 标准查询与下载
共找到 1016 条与 橡胶和塑料 相关的标准，共 68 页
This SAE Aerospace Recommended Practice (ARP) provides methods and guidelines for isolating dissimilar repair patch materials from carbon composite structure during a repair operation. These procedures are applicable to any repair procedure for carbon fiber reinforced plastic parts in which the repair patch is a metallic alloy that can form a galvanic cell with carbon in the presence of moisture or other electrolytes. The principal patch materials addressed are aluminum, titanium, and stainless steel. The procedures are primarily concerned with bolted repairs that introduce the most severe, potential corrosion problem but bonded repairs are also considered.
Isolation and Corrosion Protection of Dissimilar Materials, Carbon Composite Structure Repair
- ICS
- 49.025.40
- CCS
- Q50
- 发布
- 2013-08-15
- 实施
This specification covers a high temperature, compression set and fluid resistant fluorocarbon (FKM) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes for aeronautical and aerospace applications.
Rubber, Fluorocarbon Elastomer (FKM), 70 to 80 Hardness, Low Temperature Sealing Tg -22°F (-30°C), For Elastomeric Shapes or Parts in Gas Turbine Engine Oil, Fuel and Hydraulic Systems
- ICS
- 49.025.40
- CCS
- 发布
- 2013-08-05
- 实施
This standard specifies the requirements for glass fabric/phenolic resin preimpregnates. It shall be used together with EN 2833-1.
Aerospace series - Glass fibre thermosetting preimpregnates - Technical specification - Part 005: Glass fabric/phenolic resin preimpregnate
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-08-01
- 实施
- 2013-08-01
This European Standard describes the preparation of panels with any desired fibre orientation of unidirectional orientated carbon fibre or fabric with thermosetting resins. The purpose of this standard is to describe recommended processes for the preparation of the panels from which test specimens subsequently are machined. Standard specimens prepared in this manner may be used either for evaluating the components i.e. the carbon reinforcement, finishes, resins, catalysts, curing agents, etc. or for verifying the overall quality of the finished products.
Aerospace series - Preparation of carbon fibre reinforced resin panels for test purposes
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-08-01
- 实施
- 2013-08-01
This standard describes the procedure for normalisation of fibre dominated mechanical properties. The procedure is valid for carbon, glass and aramid reinforced laminates.
Aerospace series - Fibre composite materials - Normalisation of fibre dominated mechanical properties
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-08-01
- 实施
- 2013-08-01
This specification covers a silicone rubber material that can be used to manufacture product in the form of sheet, strip, tubing, molded shapes, and extrusions. This specification should not be used to address products such as O-rings, compression seals, O-ring cord, and molded-in-place gaskets.
Silicone Rubber, 1000 psi (6.89 MPa) Minimum Tensile Strength, 55-65 Durometer
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-07-19
- 实施
This specification covers a standard fluorosilicone (FVMQ) rubber stock in the form of molded test slabs.
Test Slabs, Fluorosilicone (FVMQ), 55-65
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-07-19
- 实施
This specification covers a fluorocarbon (FKM) rubber in the form of O-rings, O-ring cord, compression seals and molded-in-place gaskets for aeronautical and aerospace applications. These products have been used typically as sealing rings, compression seals, O-ring cord, and molded-in-place gaskets in contact with air and a wide variety of fuels, lubricants, and specific hydraulic fluids from but usage is not limited to such application. Each application should be considered individually. This class of fluoroelastomers is not recommended for use in high temperature stabilized, ""HTS"", engine oils. Each ""HTS"" oil should be evaluated separately. This fluor
Rubber: Fluorocarbon (FKM) High-Temperature/Fluid Resistant Low Compression Set /85 to 95 Hardness for Seals in Fuel Systems and Specific Engine Oil Systems
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05-20
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Fuel and synthetic oil resistant - Hardness 60 IRHD; German and English version EN 2846:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Fuel and synthetic oil resistant - Hardness 50 IRHD; German and English version EN 2845:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Chloroprene rubber (CR) - Heat resistance - Hardness 70 IRHD; German and English version EN 2838:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Chloroprene rubber (CR) - Heat resistance - Hardness 80 IRHD; German and English version EN 2839:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Mineral oil resistant - Hardness 80 IRHD; German and English version EN 2843:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Mineral oil resistant - Hardness 60 IRHD; German and English version EN 2841:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Mineral oil resistant - Hardness 70 IRHD; German and English version EN 2842:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Low temperature resistant - Hardness 70 IRHD; German and English version EN 3698:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Fuel and synthetic oil resistant - Hardness 80 IRHD; German and English version EN 2848:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Fuel and synthetic oil resistant - Hardness 70 IRHD; German and English version EN 2847:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Mineral oil resistant - Hardness 50 IRHD; German and English version EN 2840:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
Aerospace series - Acrylonitrile-butadiene rubber (NBR) - Mineral oil resistant - Hardness 90 IRHD; German and English version EN 2844:2013
- ICS
- 49.025.40
- CCS
- V13
- 发布
- 2013-05
- 实施
