53.020.99 其他起重设备 标准查询与下载

T/ZZB 1795-2020 电力电容器塔检修用桅柱式升降工作平台

本标准规定了电力电容器塔检修用桅柱式升降工作平台（以下简称升降工作平台）的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于平台最大高度30 m及以下、辅助起重装置额定载荷200 kg及以下的升降工作平台。

Power capacitor tower maintenance and repair mast column lifting work platform

T/AASE 001-2020 《智能垂直升降类机械停车设备》

本标准规定了智能垂直升降类机械停车设备的分类、技术要求、试验方法、检验规则和标志、包装、运输和贮存

Intelligent vertical lifting mechanical parking equipment

20/30400968 DC BS EN 1570-1 升降台的安全要求 第 1 部分：最多可服务两个固定平台的升降台

BS EN 1570-1. Safety requirements for lifting tables - Part 1. Lifting tables serving up to two fixed landings

JB/T 4207-2020 手动起重设备用吊钩及闭锁装置

Hooks and locking devices for manual lifting equipment

JB/T 10215-2020 垂直循环类机械式停车设备

Vertical circulation mechanical parking equipment

DB50/T 1020-2020 非接电式停车位监测控制终端技术条件

本标准适用于非接电式停车位监控终端。

Technical specifications for non-connected parking space monitoring and control terminals

BS ISO 21455:2020 移动式升降工作平台 操作员的控制 驱动、位移、位置和操作方法

1   Scope This document specifies the performance requirements, location, marking and method of operation related to operator's controls on mobile elevating work platforms (hereafter referred to as MEWPs) and takes into account operator safety and ergonomics. It applies to all controls used by an operator and includes provisions for finger, thumb, hand, and foot operated controls .

Mobile elevating work platforms. Operator's controls. Actuation, displacement, location and method of operation

JT/T 1334-2020 港口客运斜坡缆车

Harbor passenger ramp cable car

T/ZZB 1645-2020 曳引式垂直升降类机械式停车设备

本标准规定了曳引式垂直升降类机械式停车设备的基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于曳引方式驱动的垂直升降类机械式停车设备（以下简称停车设备）。 本标准不适用于易燃、易爆、腐蚀性环境中使用的垂直升降类机械式停车设备。

Traction drived vertical lifting mechanical parking system

T/ZZB 1623-2020 升降横移式非机动车停车设备

本标准规定了升降横移式非机动车停车设备的术语和定义、型式与参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本标准适用于停放符合 GB 3565 标准的两轮自行车和符合 GB 17761 标准的电动自行车的升降横移式停车设备（以下简称停车设备）。

Non-motor vehicle lift-sliding parking equipment

ASTM F3443-20 使用外骨骼时负载处理的标准实施规程

1.1 This practice provides a structure for documenting test methods used to evaluate exoskeleton success criteria during a requested load handling task. The practice does not describe all loads, load types, nor load handling methods. Instead, this practice provides manufacturers and users with example load handling test procedures of common load handling tasks and a method to record load and test parameters so that load handling tasks can be replicated. The practice includes designs for defined artifact loads and the appendix provides design details, to further allow replication of load handling tests and test results, and examples of load handling tests. 1.2 Evaluation and evaluation method would be included in another standard with inputs (for example, precision, statistical validity, etc.) provided by the test requestor. 1.3 Output of the evaluation, that is, success criteria, are provided by the requestor. 1.4 Loads encompass forces applied to physical objects, for example: lifting boxes, pushing a force plate or cart, carrying flexible firehose or luggage. 1.5 If possible, tests using real or artifact loads should be replicable and performed in environments representative of a real-world load handling implementation. 1.6 This standard includes only the use of inanimate objects. 1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are not precise mathematical conversions to imperial units. They are close approximate equivalents for the purpose of specifying material dimensions or quantities that are readily available to avoid excessive fabrication costs of test apparatuses while maintaining repeatability and reproducibility of the test method results. These values given in parentheses are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Load Handling When Using an Exoskeleton

BS 6037-2:2020 规划、设计、安装和使用永久安装的通道设备 移动梯子和龙门架 实践守则

1   Scope This part of BS 6037 gives recommendations for the planning, design, installation, use, examination, maintenance and testing of permanently installed travelling ladders and gantries (TLGs) including equipment installed on a building to facilitate routine maintenance of the building fabric and its services. It is intended for use by those involved in specifying, designing, managing the use of, maintaining and examining such equipment. NOTE 1 For further information on underbridge gantries , see The operation and maintenance of bridge access gantries and runways [4]. NOTE 2 Where TLGs are intended to be used in conjunction with suspended access equipment (SAE), this part of BS 6037 is supplemented by BS EN 1808 and BS 6037‑1.

Planning, design, installation and use of permanently installed access equipment - Travelling ladders and gantries. Code of practice

JB/T 13916-2020 钢丝绳卷扬提升式垂直升船机验收规范

Specifications for acceptance of wire rope hoisting vertical ship lifts

ISO 21455:2020 移动升降工作平台 操作员控制 驱动、位移、位置和操作方法

This document specifies the performance requirements, location, marking and method of operation related to operator's controls on mobile elevating work platforms (hereafter referred to as MEWPs) and takes into account operator safety and ergonomics. It applies to all controls used by an operator and includes provisions for finger, thumb, hand, and foot operated controls.

Mobile elevating work platforms — Operator's controls — Actuation, displacement, location and method of operation

DB43/T 1735-2020 机械式停车设备安装规范

Specifications for the installation of mechanical parking equipment

JB/T 13754-2019 桁架式液压顶升工作平台

Truss type hydraulic lifting working platform

T/ZZB 1432-2019 滚筒式巷道堆垛类机械式停车设备

本标准规定了滚筒式巷道堆垛类机械式停车设备（以下简称“停车设备”）的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于以采用滚筒交换的巷道堆垛类机械式停车设备。

Roller type aisle-stacking mechanical parking system

T/ZZB 1431-2019 滚筒式平面移动类机械式停车设备

本标准规定了滚筒式平面移动类机械式停车设备（以下简称“停车设备”）的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于于以采用滚筒交换的平面移动类机械式停车设备。

Roller type horizontal shifting mechanical parking system

DB13/T 5076-2019 C 型钩吊具安全使用技术规范

Technical specification for safe use of C-type hook spreader

T/ZZB 1368-2019 环链电动葫芦

本标准规定了环链电动葫芦的术语和定义、 型式与基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本标准适用于一般工作环境中使用的环链电动葫芦，其他环境中使用的环链电动葫芦可以参照使用。 本标准不适用于吊运熔融金属，及有爆炸性气体、可燃性粉尘、腐蚀性气体、核辐射以及有毒气体环境的环链电动葫芦。

Electric chain hoists